Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Speaker Circuit (Built-in Amplifier)

for Preparation Click here


DESCRIPTION

The radio receiver assembly sends sound signals to the speaker.

WIRING DIAGRAM


E303440E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2.CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the I1 radio receiver assembly connector.

  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    I1-2 (FL+) - I13-3 (TWL+)
    Always
    Below 1 Ω
    I1-6 (FL-) - I13-4 (TWL-)
    Always
    Below 1 Ω
    I1-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I1-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    I1-1 (FR+) - I11-3 (TWR+)
    Always
    Below 1 Ω
    I1-5 (FR-) - I11-4 (TWR-)
    Always
    Below 1 Ω
    I1-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I1-5 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    I13-1 (+) - M10-1
    Always
    Below 1 Ω
    I13-2 (-) - M10-2
    Always
    Below 1 Ω
    I13-1 (+) - Body ground
    Always
    10 kΩ or higher
    I13-2 (-) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    I11-1 (+) - L8-1
    Always
    Below 1 Ω
    I11-2 (-) - L8-2
    Always
    Below 1 Ω
    I11-1 (+) - Body ground
    Always
    10 kΩ or higher
    I11-2 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)  

7.CHECK REAR SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Quarter side speaker assembly
    A
    Rear No. 1 speaker assembly
    B



B
Go to step 10
A


8.INSPECT QUARTER SIDE SPEAKER ASSEMBLY
  1. Remove the quarter side speaker assembly (Click here).

  1. Inspect the quarter side speaker assembly (Click here).



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - QUARTER SIDE SPEAKER ASSEMBLY)
  1. Disconnect the I2 radio receiver assembly connector.

  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    I2-2 (RL+) - O31-1 (+)
    Always
    Below 1 Ω
    I2-6 (RL-) - O31-2 (-)
    Always
    Below 1 Ω
    I2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I2-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    I2-1 (RR+) - O37-1 (+)
    Always
    Below 1 Ω
    I2-3 (RR-) - O37-2 (-)
    Always
    Below 1 Ω
    I2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I2-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

10.INSPECT REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly (Click here).

  1. Inspect the rear No. 1 speaker assembly (Click here).



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (QUARTER SIDE SPEAKER ASSEMBLY - REAR NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Condition
    Specified Condition
    O31-3 (+) - N7-1
    Always
    Below 1 Ω
    O31-4 (-) - N7-2
    Always
    Below 1 Ω
    O31-3 (+) - Body ground
    Always
    10 kΩ or higher
    O31-4 (-) - Body ground
    Always
    10 kΩ or higher
    for RH 
    Tester Connection
    Condition
    Specified Condition
    O37-3 (+) - N1-1
    Always
    Below 1 Ω
    O37-4 (-) - N1-2
    Always
    Below 1 Ω
    O37-3 (+) - Body ground
    Always
    10 kΩ or higher
    O37-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)