Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short in CAN Bus Lines

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. Combination meter ECU
  3. Main body ECU
  4. Skid control ECU
  5. Steering angle sensor
  6. Center airbag sensor
  7. Bus buffer ECU*1
  8. Air conditioning amplifier
  9. ECM
  10. Power steering ECU
  11. 4WD control ECU*2
  12. Suspension control ECU*3
  13. No. 1 junction connector
  14. No. 2 junction connector
  15. No. 4 junction connector*3
*1: w/ Bus Buffer ECU
*2: w/ 4WD
*3: w/ Air Suspension

WIRING DIAGRAM


C202972E04


C202973E02


C221930E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK CONNECTOR
  1. Check the type of No. 2 junction connector.
    Result 
    Result
    Proceed to
    for 2-pin Connector
    A
    for 22-pin Connector
    B



B
Go to step 33
A


3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)


    H102629E01
  1. Disconnect the H93 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the H93 No. 1 junction connector.


NEXT


5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)


    H102629E01
  1. Disconnect the H100 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 13
OK


6.CONNECT CONNECTOR
  1. Reconnect the H100 No. 2 junction connector.


NEXT


7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    C159609E15
  1. Disconnect the H92 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H92-1 (CANH) - H92-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 10
OK


8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without bus buffer ECU, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - ECM)".



    C159609E16
  1. Disconnect the H105 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H105-1 (CANH) - H105-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 11
OK


9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - ECM)


    C159609E18
  1. Disconnect the H99 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H99-1 (CANH) - H99-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 12
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

10.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER)


    C159609E15
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H92-1 (CANH) - H92-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

11.CHECK FOR SHORT IN CAN BUS WIRES (BUS BUFFER ECU)


    C159609E16
  1. Disconnect the H66 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H105-1 (CANH) - H105-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

12.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    C159609E18
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H99-1 (CANH) - H99-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)  

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C159609E12
  1. Disconnect the H101 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H101-1 (CANH) - H101-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


14.CONNECT CONNECTOR
  1. Reconnect the H101 No. 1 junction connector.

  1. Reconnect the H100 No. 2 junction connector.


NEXT


15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR SIDE)

NOTICE:
For vehicles without an air suspension, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Combination Meter ECU)".



    H102629E01
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 19
OK


16.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)


    E158732E04
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-6 (CANH) - O42-12 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 26
OK


18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)


    E158732E06
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - O41-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 27
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C137766E80
  1. Disconnect the H91 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H91-1 (CANH) - H91-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)

NOTICE:
For vehicles with an air suspension, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Power Steering ECU)".



    C137766E80
  1. Disconnect the H91 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H91-1 (CANH) - H91-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 27
OK


21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU)


    C159609E11
  1. Disconnect the H106 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H106-1 (CANH) - H106-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 28
OK


22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C159609E19
  1. Disconnect the H103 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H103-1 (CANH) - H103-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 29
OK


23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C137766E81
  1. Disconnect the A59 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-1 (CANH) - A59-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 30
OK


24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C159609E20
  1. Disconnect the H94 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H94-1 (CANH) - H94-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 31
OK


25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)


    C137766E82
  1. Disconnect the H90 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H90-1 (CANH) - H90-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 32
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

26.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)


    E158732E04
  1. w/ AVS:

    1. Disconnect the O18 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O42-6 (CANH) - O42-12 (CANL)
      Ignition switch off
      1 MΩ or higher

  1. w/o AVS:

    1. Disconnect the O19 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O42-6 (CANH) - O42-12 (CANL)
      Ignition switch off
      1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

27.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C159487E22
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

28.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU)


    C159609E11
  1. Disconnect the H38 power steering ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H106-1 (CANH) - H106-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU (Click here)  

29.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159609E19
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H103-1 (CANH) - H103-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU 

30.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)


    C137766E81
  1. Disconnect the A19 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-1 (CANH) - A59-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY (Click here)  

31.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    C159609E20
  1. Disconnect the H6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H94-1 (CANH) - H94-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

32.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR)


    C137766E82
  1. Disconnect the H56 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H90-1 (CANH) - H90-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR (Click here)  

33.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)


    H102629E01
  1. Disconnect the H93 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


34.CONNECT CONNECTOR
  1. Reconnect the H93 No. 1 junction connector.


NEXT


35.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)


    H102629E01
  1. Disconnect the H110 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 44
OK


36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    C198236E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-1 (CANH) - H110-12 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 40
OK


37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without a bus buffer ECU, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - 4WD Control ECU)".



    C198236E74
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-5 (CANH) - H110-16 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 41
OK


38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without 4WD, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - ECM)".



    C198236E90
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-2 (CANH) - H110-13 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 42
OK


39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - ECM)


    C198236E75
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-3 (CANH) - H110-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 43
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR 

40.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER)


    C198236E73
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-1 (CANH) - H110-12 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

41.CHECK FOR SHORT IN CAN BUS WIRES (BUS BUFFER ECU)


    C198236E74
  1. Disconnect the H66 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-5 (CANH) - H110-16 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

42.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)


    C198236E90
  1. Disconnect the A28 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-2 (CANH) - H110-13 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU (Click here)  

43.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    C198236E75
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-3 (CANH) - H110-14 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)  

44.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C159609E12
  1. Disconnect the H101 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H101-1 (CANH) - H101-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


45.CONNECT CONNECTOR
  1. Reconnect the H101 No. 1 junction connector.

  1. Reconnect the H110 No. 2 junction connector.


NEXT


46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR SIDE)

NOTICE:
For vehicles without an air suspension, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Combination Meter ECU)".



    H102629E01
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 50
OK


47.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


48.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)


    E158732E04
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-6 (CANH) - O42-12 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 57
OK


49.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)


    E158732E06
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - O41-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 58
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

50.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C137766E80
  1. Disconnect the H91 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H91-1 (CANH) - H91-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


51.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)

NOTICE:
For vehicles with an air suspension, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Power Steering ECU)".



    C137766E80
  1. Disconnect the H91 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H91-1 (CANH) - H91-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 58
OK


52.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU)


    C159609E11
  1. Disconnect the H106 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H106-1 (CANH) - H106-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 59
OK


53.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C159609E19
  1. Disconnect the H103 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H103-1 (CANH) - H103-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 60
OK


54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C137766E81
  1. Disconnect the A59 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-1 (CANH) - A59-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 61
OK


55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C159609E20
  1. Disconnect the H94 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H94-1 (CANH) - H94-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 62
OK


56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)


    C137766E82
  1. Disconnect the H90 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H90-1 (CANH) - H90-2 (CANL)
    Ignition switch off
    200 Ω or higher



NG
Go to step 63
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR 

57.CHECK FOR SHORT IN CAN BUS WIRES (SUSPENSION CONTROL ECU)


    E158732E04
  1. w/ AVS:

    1. Disconnect the O18 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O42-6 (CANH) - O42-12 (CANL)
      Ignition switch off
      1 MΩ or higher

  1. w/o AVS:

    1. Disconnect the O19 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O42-6 (CANH) - O42-12 (CANL)
      Ignition switch off
      1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

58.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C159487E22
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

59.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU)


    C159609E11
  1. Disconnect the H38 power steering ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H106-1 (CANH) - H106-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU (Click here)  

60.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159609E19
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H103-1 (CANH) - H103-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU 

61.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)


    C137766E81
  1. Disconnect the A19 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A59-1 (CANH) - A59-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY (Click here)  

62.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    C159609E20
  1. Disconnect the H6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H94-1 (CANH) - H94-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

63.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR)


    C137766E82
  1. Disconnect the H56 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H90-1 (CANH) - H90-2 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR (Click here)