Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line

for Preparation Click here


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen, one side of the CAN branch wire may be open. (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open.)

Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on intelligent tester "CAN Bus Check" screen.
  1. One side of CAN branch wire is open
  2. Main body ECU
  3. Skid control ECU
  4. Steering angle sensor
  5. Center airbag sensor
  6. Bus buffer ECU*1
  7. Air conditioning amplifier
  8. 4WD control ECU*2
  9. Suspension control ECU*3
  10. Power steering ECU
*1: w/ Bus Buffer ECU
*2: w/ 4WD
*3: w/ Air Suspension

WIRING DIAGRAM


C202972E04


C202973E02


C221930E01


INSPECTION PROCEDURE

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  2. Do not remove the combination meter and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  3. The open circuit confirmation of the combination meter, ECM and main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
  1. Disconnect the H2 main body ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    Main Body not displayed on intelligent tester.
    A
    Several ECUs and sensors other than Main Body not displayed on intelligent tester.
    B



B
Go to step 3
A


2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C159597E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H2-6 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
  1. Disconnect the A19 skid control ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    ABS/VSC/TRC not displayed on intelligent tester.
    A
    Several ECUs and sensors other than ABS/VSC/TRC not displayed on intelligent tester.
    B



B
Go to step 5
A


4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C240487E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A19-12 (CANH) - A19-13 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)
OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY (Click here)  

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
  1. Disconnect the H6 steering angle sensor connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    Steering Angle Sensor not displayed on intelligent tester.
    A
    Several ECUs and sensors other than Steering Angle Sensor not displayed on intelligent tester.
    B



B
Go to step 7
A


6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C159495E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H6-9 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU)

NOTICE:
For vehicles without a bus buffer ECU, go to "Check for Open in One Side of CAN Branch Wire (Center Airbag Sensor)".

  1. Disconnect the H66 bus buffer ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    Accessory Gateway not displayed on intelligent tester.
    A
    Several ECUs and sensors other than Accessory Gateway not displayed on intelligent tester.
    B



B
Go to step 9
A


8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C159599E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H66-2 (CAN-)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (BUS BUFFER ECU)
OK

REPLACE BUS BUFFER ECU 

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR)
  1. Disconnect the H56 center airbag sensor connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    SRS Airbag not displayed on intelligent tester.
    A
    Several ECUs and sensors other than SRS Airbag not displayed on intelligent tester.
    B



B
Go to step 11
A


10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C159494E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H56-22 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR)
OK

REPLACE CENTER AIRBAG SENSOR (Click here)  

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU)
  1. Disconnect the H38 power steering ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here ).
    Result 
    Result
    Proceed to
    EPS not displayed on intelligent tester.
    A
    Several ECUs and sensors other than EPS not displayed on intelligent tester.
    B



B
Go to step 13
A


12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    E158738E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H38-8 (CANH) - H38-3 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU)
OK

REPLACE POWER STEERING ECU (Click here)  

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU)

NOTICE:
For vehicles without an air suspension, go to "Check for Open in One Side of CAN Branch Wire (4WD Control ECU)".

  1. Disconnect the O18 suspension control ECU connector (w/ AVS) or O19 suspension control ECU connector (w/o AVS).

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    Air Suspension not displayed on intelligent tester.
    A
    Several ECUs and sensors other than Air Suspension not displayed on intelligent tester.
    B



B
Go to step 15
A


14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    E158740E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O18-30 (CANH) - O18-29 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O19-29 (CANH) - O19-28 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SUSPENSION CONTROL ECU)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU)

NOTICE:
For vehicles without 4WD, go to "Check for Open in One Side of CAN Branch Wire (Air Conditioning Amplifier)".

  1. Disconnect the A28 4WD control ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    Four Wheel Drive Control not displayed on intelligent tester.
    A
    Several ECUs and sensors other than Four Wheel Drive Control not displayed on intelligent tester.
    B



B
Go to step 17
A


16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C159487E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (4WD CONTROL ECU)
OK

REPLACE 4WD CONTROL ECU (Click here)  

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C159487E18
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H24-12 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)