Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line

for Preparation Click here


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
  1. Air conditioning amplifier assembly
  2. 4 wheel drive control ECU (4WD control ECU)*1
  3. Bus buffer ECU*2
  4. Network gateway ECU*3
  5. Center airbag sensor assembly
  6. Steering angle sensor
  7. Main body ECU (cowl side junction block LH)
  8. Power steering ECU assembly
  9. Suspension control ECU*4
  10. Brake actuator assembly (skid control ECU)
  11. CAN branch wire or connector
  1. *1: for 4WD
  2. *2: w/ Bus Buffer ECU
  3. *3: w/ Blind Spot Monitor System
  4. *4: w/ Air Suspension System

WIRING DIAGRAM


C242851E03


C245666E01


C242853E02


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  2. Do not remove the combination meter assembly and ECM as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  3. The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of a CAN branch wire.

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the H24 air conditioning amplifier assembly connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Air Conditioning Amplifier" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the intelligent tester
    B



B
Go to step 3
A


2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)


    C227940E03
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H24-12 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU)

NOTICE:
For vehicles without an 4WD, go to "Check for Open in One Side of CAN Branch Wire (Bus Buffer ECU)".

  1. Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Four Wheel Drive Control" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the intelligent tester
    B



B
Go to step 5
A


4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU CAN BRANCH WIRE)


    C242857E01
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to 4 Wheel Drive Control ECU [4WD Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (4WD CONTROL ECU)
OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (Click here)  

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU)

NOTICE:
For vehicles without an bus buffer ECU, go to "Check for Open in One Side of CAN Branch Wire (Network Gateway ECU)".

  1. Disconnect the H66 bus buffer ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Accessory Gateway" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Accessory Gateway" are displayed on the intelligent tester
    B



B
Go to step 7
A


6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU CAN BRANCH WIRE)


    C242858E01
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H66-2 (CAN-)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Bus Buffer ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (BUS BUFFER ECU)
OK

REPLACE BUS BUFFER ECU 

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)

NOTICE:
For vehicles without an blind spot monitor system, go to "Check for Open in One Side of CAN Branch Wire (Center Airbag Sensor Assembly)".

  1. Disconnect the H120 network gateway ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "CAN Gateway1" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "CAN Gateway1" are displayed on the intelligent tester
    B



B
Go to step 9
A


8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)


    C242749E03
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-16 (CA1H) - H120- 15 (CA1L)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NETWORK GATEWAY ECU)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the H56 center airbag sensor assembly connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Airbag" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Airbag" are displayed on the intelligent tester
    B



B
Go to step 11
A


10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)


    C222818E13
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H56-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    Result 
    Result
    Proceed to
    OK (w/ Cool Box)
    A
    OK (w/o Cool Box)
    B
    NG
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
  1. Disconnect the H6 steering angle sensor connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here ).
    Result 
    Result
    Proceed to
    "Spiral cable (Steering Angle Sensor)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the intelligent tester
    B



B
Go to step 13
A


12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)


    C242861E01
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H6-9 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Main Body" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Main Body" are displayed on the intelligent tester
    B



B
Go to step 15
A


14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)


    C242862E01
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H2-6 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
  1. Disconnect the H112 power steering ECU assembly connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Power Steering (EPS)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Power Steering (EPS)" are displayed on the intelligent tester
    B



B
Go to step 17
A


16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)


    E211085E07
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H112-1 (CANH) - H112-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU)

NOTICE:
For vehicles without an air suspension control system, go to "Check for Open in One Side of CAN Branch Wire (Skid Control ECU)".

  1. Disconnect the O16*1 or O19*2 suspension control ECU connector.

    1. *1: w/ AVS
    2. *2: w/o AVS

  1. Select "CAN Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Suspension Control (Air Suspension)" is not displayed on the intelligent tester
    A
    Several ECUs and sensors in addition to "Suspension Control (Air Suspension)" are displayed on the intelligent tester
    B



B
Go to step 19
A


18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)


    C245665E01
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O16-7 (CANH) - O16-8 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O19-29 (CANH) - O19-28 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ AVS
    *B
    w/o AVS
    *a
    Front view of wire harness connector
    (to Suspension Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SUSPENSION CONTROL ECU)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)


    C243210E01
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the A19 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A19-12 (CANH) - A19-13 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)