POWER BACK DOOR SYSTEM > Power Back Door cannot be Operated Using Any Switch |

| 1.INITIALIZE POWER BACK DOOR ECU |
Check that the power back door drive unit (power back door ECU) can be initialized (Click here).
| NEXT | |
| 2.CHECK POWER BACK DOOR SYSTEM |
Check the power back door system operation.
|
| ||||
| OK | ||
| ||
| 3.CHECK BACK DOOR CLOSER SYSTEM |
Check the back door closer system operation (Click here).
|
| ||||
| OK | |
| 4.CHECK COMBINATION METER |
Check the A/T shift position indicator operation.
Check that the speedometer indicates 0 km/h (0 mph) when the vehicle is stopped and the engine idling.
|
| ||||
| OK | |
| 5.CHECK DTC OUTPUT |
Check for the DTCs (Click here).
| Result | Proceed to |
| DTC is not output | A |
| B2250 is output | B |
| B2251 is output | C |
|
| ||||
|
| ||||
| A | |
| 6.READ VALUE USING INTELLIGENT TESTER (BACK DOOR LOCK) |
Connect the intelligent tester to the DLC3
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Back Door Open | Back door lock / Permit or Prohibit | Permit: Back door is unlocked Prohibit: Back door is locked | - |
|
| ||||
| OK | |
| 7.READ VALUE USING INTELLIGENT TESTER (POWER BACK DOOR TOUCH SENSOR) |
Connect the intelligent tester to the DLC3
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Back Door / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| PBD Touch Sen L | Power back door touch sensor LH signal / ON or OFF | ON: Power back door touch sensor LH pressed OFF: Power back door touch sensor LH not pressed | - |
| PBD Touch Sen R | Power back door touch sensor RH signal / ON or OFF | ON: Power back door touch sensor RH pressed OFF: Power back door touch sensor RH not pressed | - |
|
| ||||
| OK | |
| 8.READ VALUE USING INTELLIGENT TESTER (POWER BACK DOOR MAIN SWITCH) |
Connect the intelligent tester to the DLC3
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Back Door / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| PBD Main SW | Power back door main switch / ON or OFF | ON: Power back door main switch is not pushed OFF: Power back door main switch is pushed | - |
|
| ||||
| OK | ||
| ||
| 9.INSPECT POWER BACK DOOR MAIN SWITCH |
![]() |
Remove the power back door main switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (MSE) - 9 (MSW) | Pushed (OFF) | 10 kΩ or higher |
| 6 (MSE) - 9 (MSW) | Not pushed (ON) | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (MAIN SWITCH - BACK DOOR ECU AND BODY GROUND) |
![]() |
Disconnect the H69 switch connector.
Disconnect the O30 ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H69-9 (MSW) - O30-17 (MSW) | Always | Below 1 Ω |
| H69-6 (MSE) - Body ground | Always | Below 1 Ω |
| H69-9 (MSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||