Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM J

3UR-FBE ENGINE CONTROL  SFI SYSTEM  Cranking Holding Function Circuit  


DESCRIPTION

The cranking holding control system provides current to the starter when the ECM detects the ignition switch's start signal (STSW). When the ECM performs a firing judgment, the system cuts current to the starter. When an ECM receives the STSW signal, it turns on the ACC Cut relay, which prevents flickering of the combination meter, clock, audio system, etc. Also, the ECM sends a signal to the ECM's STAR terminal. Then the STAR output signal travels through the Park/Neutral Position (PNP) switch to the STARTER relay, causing the starter to activate.

When the engine is cranking, the starter operation signal is sent to the ECM's STA terminal.

A103821E81
3.188,4.5 2.719,4.615 false 4.677,4.104 4.906,3.802 false 0.083,1.448 1.781,1.688 1.698,0.24 10 false Start Input Signal (STSW) 0.073,2.365 1.813,2.594 1.74,0.229 10 false Start Output Signal (STAR) 0.073,3.031 1.813,3.573 1.74,0.542 10 false ACC Cut Relay Input Signal (ACCR) (for Start Control) 0.094,4.354 1.792,4.615 1.698,0.26 10 false Engine Speed Signal (NE) 1.906,4.625 3.604,4.885 1.698,0.26 10 false Ignition Switch ST Position 2.021,1.042 2.323,1.24 0.302,0.198 10 false ON 1.979,1.49 2.385,1.708 0.406,0.219 10 false OFF 2.021,1.948 2.323,2.146 0.302,0.198 10 false ON 1.979,2.396 2.385,2.615 0.406,0.219 10 false OFF 2.021,2.969 2.323,3.167 0.302,0.198 10 false ON 1.979,3.417 2.385,3.635 0.406,0.219 10 false OFF 2.927,5.073 4.135,5.302 1.208,0.229 10 false Elapsed Time 4.948,0.469 6.813,0.865 1.865,0.396 10 false Keeps cranking until the firing of the engine is judged 4.958,1.74 6.635,2.094 1.677,0.354 10 false When no cranking holding control is performed 4.948,2.781 6.74,3.135 1.792,0.354 10 false Prevents meters, clock, etc. from flickering 4.969,3.667 6.531,3.885 1.563,0.219 10 false Firing Judgment Line 4.635,4.271 6.573,4.958 1.938,0.688 10 false When the NE signal reaches a predetermined value, the ECM determines that the engine has started successfully

WIRING DIAGRAM

A243747E01
5.953,1.235 6.322,1.400 0.369,0.165 10 NSW 5.953,0.849 6.358,1.015 0.405,0.165 10 STAR 5.953,0.373 6.419,0.538 0.466,0.165 10 STSW 5.953,1.718 6.322,1.883 0.369,0.165 10 STA 5.612,1.633 5.886,1.793 0.274,0.160 10 A27 5.612,1.234 5.886,1.394 0.274,0.160 10 D56 5.612,0.842 5.886,1.002 0.274,0.160 10 D56 5.612,0.377 5.886,0.537 0.274,0.160 10 A27 5.616,1.077 5.883,1.226 0.267,0.149 10 120 5.651,1.472 5.835,1.622 0.184,0.151 10 46 5.651,0.205 5.835,0.355 0.184,0.151 10 14 5.651,0.667 5.835,0.818 0.184,0.151 10 16 4.912,1.55 5.020,1.699 0.107,0.149 10 5 4.163,1.55 4.270,1.699 0.107,0.149 10 4 4.18,1.919 4.475,2.075 0.295,0.156 10 D21 4.18,2.041 5.160,2.386 0.980,0.345 10 Park/Neutral Position Switch 2.42,1.861 2.707,2.017 0.288,0.156 10 A41 2.42,1.994 2.808,2.146 0.389,0.152 10 Diode 1.858,1.546 1.972,1.695 0.114,0.149 10 7 0.604,1.546 0.718,1.695 0.114,0.149 10 5 1.528,1.721 1.813,1.874 0.284,0.152 10 ST2 1.213,3.585 1.446,3.737 0.232,0.152 10 ST 3.329,3.276 3.561,3.429 0.232,0.152 10 ST 0.744,1.721 1.066,1.874 0.323,0.152 10 AM2 0.46,2.846 0.783,2.998 0.323,0.152 10 AM2 3.742,2.501 3.849,2.650 0.107,0.149 10 3 3.009,2.501 3.116,2.650 0.107,0.149 10 5 3.002,2.889 3.109,3.038 0.107,0.149 10 2 3.74,2.889 3.847,3.038 0.107,0.149 10 1 4.183,5.287 4.298,5.443 0.114,0.156 10 1 3.651,5.315 3.765,5.471 0.114,0.156 10 1 3.913,5.287 4.125,5.436 0.211,0.149 10 E7 3.611,5.476 3.823,5.625 0.211,0.149 10 E8 3.707,5.924 4.169,6.080 0.461,0.156 10 Starter 6.31,4.681 6.653,4.837 0.343,0.156 10 ECM 1.388,6.044 1.871,6.213 0.482,0.170 10 Battery 0.799,2.339 1.733,2.495 0.934,0.156 10 Ignition Switch 0.799,2.2 1.083,2.370 0.284,0.170 10 H10 4.307,1.545 4.458,1.696 0.151,0.151 10 B 4.76,1.549 4.894,1.700 0.134,0.151 10 L

PROCEDURE

1.CHECK CRANKING
a.

Check the cranking of the engine.

Result
Test Result Proceed to
Cranking possible and holding control operates A
Does not crank B
Cranking possible but holding control does not operate C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)

C

11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Read values.


f.

Check the result when the ignition switch is turned to ON and when the engine is started.

Standard:
Ignition Switch Position Display (Starter Signal)
ON OFF
START ON




OK

3.INSPECT STARTER RELAY (ST)

NG

7.CHECK IGNITION SWITCH (POWER SOURCE)
3.INSPECT STARTER RELAY (ST)
a.
E145692E22
2.667,0.708 3.042,0.708 false 1.615,0.729 2,0.729 false 2.531,1.125 3.052,1.125 false 2.531,1.625 3.042,1.625 false 0.208,1.271 0.365,1.448 0.156,0.177 10 false 1 1.198,1.281 1.354,1.458 0.156,0.177 10 false 2 0.208,0.74 0.365,0.917 0.156,0.177 10 false 3 1.198,0.729 1.354,0.906 0.156,0.177 10 false 5 1.51,0.646 1.667,0.823 0.156,0.177 10 false 1 3.083,0.604 3.24,0.781 0.156,0.177 10 false 2 3.083,1.51 3.24,1.688 0.156,0.177 10 false 3 3.083,1.021 3.24,1.198 0.156,0.177 10 false 5

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When no battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (ST RELAY - PNP SWITCH)

NG

REPLACE STARTER RELAY (ST)

4.CHECK HARNESS AND CONNECTOR (ST RELAY - PNP SWITCH)
A379966E03
1.458,0.99 1.865,1.25 0.406,0.26 1.344,1.844 1.01,2.104 true 1.969,1.688 2.177,2.125 true 0.177,0.104 2.479,0.479 2.302,0.375 10 false Front view of wire harness connector: (to PNP Switch) 1.531,1.031 1.865,1.229 0.333,0.198 10 false D21 0.844,2.052 1,2.25 0.156,0.198 10 false L 5.042,0.542 5.313,0.729 0.271,0.188 10 false ST 3.188,0.115 4.979,0.313 1.792,0.198 10 false Engine Room Relay Block: 2.156,2.146 2.313,2.344 0.156,0.198 10 false B

a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the D21 PNP switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
ST relay (1) - D21-5 (L) Always Below 1 Ω
ST relay (1) or D21-5 (L) - Body ground Always 10 kΩ or higher




OK

5.CHECK STARTER RELAY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STARTER RELAY (POWER SOURCE)
A162331E01
0.08,0.139 1.745,0.323 1.665,0.184 10 Engine Room Relay Block 1.73,1.835 1.969,2.000 0.239,0.165 10 ST

a.

Remove the ST relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
ST relay (2) - ST relay (5) Always 11 to 14 V




OK

6.INSPECT STARTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BATTERY, BODY GROUND)

6.INSPECT STARTER

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - STARTER RELAY (ST), BATTERY)

NG

REPAIR OR REPLACE STARTER

7.CHECK IGNITION SWITCH (POWER SOURCE)
U153003E01
0.048,0.037 2.392,0.367 2.343,0.330 10 Front view of wire harness connector: (to Ignition Switch) 0.369,1.896 0.662,2.051 0.292,0.155 10 H10 1.961,2.794 2.290,2.942 0.330,0.149 10 AM2 1.382,2.163 1.915,2.867 false

a.

Disconnect the H10 ignition switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
H10-5 (AM2) - Body ground Always 11 to 14 V




OK

8.INSPECT IGNITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY POSITIVE TERMINAL)

8.INSPECT IGNITION SWITCH
a.


OK

9.INSPECT PARK/NEUTRAL POSITION SWITCH (POWER SOURCE)

NG

9.INSPECT PARK/NEUTRAL POSITION SWITCH (POWER SOURCE)
U153455E02
2.115,1.667 2.552,2.542 false 0.146,0.115 2.552,0.479 2.406,0.365 10 false Front view of wire harness connector: (to Park / Neutral Position Switch) 0.396,1.667 0.771,1.896 0.375,0.229 10 false D21 2.5,2.563 2.719,2.75 0.219,0.188 10 false B

a.

Disconnect the D21 PNP switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
D21-4 (B) - Body ground While cranking the engine 11 to 14 V




OK

10.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - IGNITION SWITCH)

10.INSPECT PARK/NEUTRAL POSITION SWITCH
C160109E23
0.056,0.001 2.638,0.368 2.582,0.367 10 Component without harness connected: (Park / Neutral Position Switch) 0.951,2.299 1.100,2.480 0.149,0.181 10 B 2.335,2.267 2.545,2.448 0.210,0.181 10 L 2.301,2.345 2.02,1.898 false 1.378,1.702 1.078,2.351 false

a.

Disconnect the D21 PNP switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
4 (B) - 5 (L) Shift lever position P Below 1 Ω
Shift lever position N Below 1 Ω


Result
Result Proceed to
OK A
NG B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - ECM)

B

11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
a.

Disconnect the H10 ignition switch connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
H10-7 (ST2) - A27-14 (STSW) Always Below 1 Ω
H10-7 (ST2) or A27-14 (STSW) - Body ground Always 10 kΩ or higher




OK

12.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM)
a.

Disconnect the D21 PNP switch connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D21-4 (B) - D56-16 (STAR) Always Below 1 Ω
D21-4 (B) or D56-16 (STAR) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR