Refer to DTC P0115 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0115).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0116 | When either of following conditions met (2 trip detection logic):
·
When cold engine started and engine warmed up, Engine Coolant Temperature (ECT) sensor value does not change. ·
After warmed up engine stopped and then next cold engine start performed, ECT sensor value does not change. |
·
Thermostat ·
ECT sensor |
When a cold engine start is performed and then the engine is warmed up, if the ECT sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
If the ECT sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
| Related DTCs | P0116: Engine coolant temperature (ECT) sensor cold start monitor
P0116: ECT sensor soak monitor |
| Required Sensors/Components (Main) | ECT sensor |
| Required Sensors/Components (Related) | None |
| Frequency of Operation | Once per driving cycle |
| Duration | -: Cold start monitor
10 seconds: Soak monitor |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 10.5 V or more |
| Time after engine start | 1 second or more |
| ECT at engine start | Less than 60°C (140°F) |
| Soak time | 0 seconds or more |
| Accumulated MAF | 8727 g or more |
| Fuel cut | OFF |
| Difference between ECT at engine start and IAT | Less than 40°C (72°F) |
| Intake air temperature sensor circuit failure (P0112, P0113) | Not detected |
| Engine coolant temperature circuit failure (P0115, P0117, P0118, P0125) | Not detected |
| Thermostat failure (P0128) | Not detected |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 10.5 V or more |
| Engine | Running |
| Soak time | 5 hours or more |
| Either (a) or (b) condition met | - |
| (a) ECT | 60°C (140°F) or more |
| (b) Accumulated MAF | 17454 g or more |
| Intake air temperature sensor circuit failure (P0112, P0113) | Not detected |
| Engine coolant temperature circuit failure (P0115, P0117, P0118, P0125) | Not detected |
| Thermostat failure (P0128) | Not detected |
| Soak timer circuit failure (P2610) | Not detected |
| ECT sensor value change | Less than 5°C (9°F) |
| Difference between current ECT sensor value and previous ECT sensor value when engine stopped | Less than 5°C (9°F) [varies with ECT of last trip engine stop] |
| ECT | ECT sensor value changes in accordance with actual ECT |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Check that the coolant temperature is 60°C (140°F) or less.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine and idle it for 5 minutes or more [B].
If the engine coolant temperature does not change by 5°C (9°F) or more, the ECT sensor is malfunctioning. It is not necessary to continue this procedure.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0116.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].
Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].
In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.
Check the DTC judgment result again [E].
If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
If DTC P0115, P0117, P0118 or P0125 is set simultaneously with DTC P0116, the ECT sensor may have an open or a short circuit. Troubleshoot those DTCs first.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTC.
| Result | Proceed to |
|---|---|
| P0116 is output | A |
| P0116 and other DTCs are output | B |
A
B
Remove the thermostat (See page Engine / Hybrid System>3UR-FBE COOLING>THERMOSTAT>REMOVAL).
Measure the valve opening temperature of the thermostat.
80 to 84°C (176 to 183°F)
In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.
Reinstall the thermostat (See page Engine / Hybrid System>3UR-FBE COOLING>THERMOSTAT>INSTALLATION).
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG