Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P0141  Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)  P0161  Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION


HINT:
·

When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) Sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.

A164717E06
0.039,0.007 2.909,0.307 2.869,0.300 10 Reference (System Diagram): 2.829,1.184 3.509,1.365 0.680,0.181 10 EFI NO. 2 2.12,2.629 2.742,2.785 0.621,0.156 10 EFI MAIN 1.231,1.217 1.885,1.398 0.653,0.181 10 EFI NO. 1 1.02,3.33 1.500,3.512 0.480,0.181 10 Ground 3.751,2.121 4.585,2.302 0.834,0.181 10 HO2 Sensor 3.557,0.937 3.782,1.118 0.226,0.181 10 +B 4.368,0.937 4.748,1.118 0.380,0.181 10 HT1B 3.564,1.5 3.821,1.681 0.258,0.181 10 E1 4.362,1.5 4.786,1.681 0.424,0.181 10 OX1B 5.376,1.48 5.800,1.661 0.424,0.181 10 OX1B 5.396,2.269 5.820,2.450 0.424,0.181 10 EX1B 3.958,1.184 4.394,1.365 0.436,0.181 10 Heater 3.916,1.792 4.375,1.973 0.459,0.181 10 Sensor 6.209,3.416 6.535,3.598 0.326,0.181 10 ECM 5.369,0.949 5.749,1.131 0.380,0.181 10 HT1B 5.389,2.852 5.792,3.033 0.403,0.181 10 MREL 0.485,1.002 0.977,1.363 0.492,0.360 10 from Battery



DTC No. DTC Detection Condition Trouble Area
P0037
P0057
The heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
·

Open in HO2 sensor heater circuit

·

HO2 sensor heater (for Sensor 2)

·

Integration relay

·

ECM


P0038
P0058
The heater current is higher than the specified value while the heater is operating.
(1 trip detection logic)
·

Short in HO2 sensor heater circuit

·

HO2 sensor heater (for Sensor 2)

·

Integration relay

·

ECM


P0141
P0161
The cumulative heater resistance correction value exceeds the threshold.
(2 trip detection logic)
·

Open or short in HO2 sensor heater circuit

·

HO2 sensor heater (for Sensor 2)

·

Integration relay

·

ECM


P102D
P105D
The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The sensing portion of the Heated Oxygen (HO2) sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated oxygen sensor heater range check (P0037, P0038, P0057, P0058, P102D and P105D):

The ECM monitors the current applied to the O2 sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM determines that there is an open circuit in the heater. If the current is above the threshold value, the ECM determines that there is a short circuit in the heater.

The ECM constantly monitors the current applied to the heater. If the ECM detects an open or short circuit, the ECM turns the MIL on and sets a DTC.

If a malfunction is detected, the ECM cuts off the current applied to the heater.


Heated oxygen sensor heater performance (P0141 and P0161):

After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using the battery voltage and the current applied to the heater.

If the resistance is above the threshold value, the ECM determines that there is a malfunction in the HO2 sensor heater and sets DTC P0141 or P0161.


MONITOR STRATEGY

Related DTCs P0037: Heated oxygen sensor heater (for Bank 1) range check (Low electrical current)
P0038: Heated oxygen sensor heater (for Bank 1) range check (High electrical current)
P0057: Heated oxygen sensor heater (for Bank 2) range check (Low electrical current)
P0058: Heated oxygen sensor heater (for Bank 2) range check (High electrical current)
P0141: Heated oxygen sensor heater performance (for Bank 1)
P0161: Heated oxygen sensor heater performance (for Bank 2)
P102D: Heated oxygen sensor heater stuck ON (for Bank 1 Sensor 2)
P105D: Heated oxygen sensor heater stuck ON (for Bank 2 Sensor 2)
Required Sensors/Components (Main) Heated oxygen sensor heater
Required Sensors/Components (Related) -
Frequency of Operation Continuous: P0037, P0038, P0057, P0058 P102D and P105D
Once per driving cycle: P0141 and P0161
Duration 0.5 seconds: P0037, P0057, P102D and P105D
Within 3 seconds: P0038 and P0058
10 seconds: P0141 and P0161
MIL Operation Immediate: P0037, P0038, P0057, P0058, P102D and P105D
2 driving cycles: P0141 and P0161
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0037 and P0057 (Case 1)
Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or higher
Engine Running
Starter OFF
Catalyst active A/F control Not operating
Time after heater ON 10 seconds or more
Learned heater OFF current operation Complete
Learned heater OFF current operation Succeeded
Heated oxygen sensor heater high current failure (P0038, P0058) Not detected

P0037 and P0057 (Case 2)
Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or higher
Engine Running
Starter OFF
Catalyst active A/F control Not operating
Time after heater ON 10 seconds or more
Learned heater OFF current operation Complete
Heated oxygen sensor heater OFF current Higher than 3.5 A
Hybrid IC high current limiter monitor Fail
Heated oxygen sensor heater current failure (P0037, P0038, P0057, P0058) Not detected

P0038 and P0058
Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or higher
Engine Running
Starter OFF
Catalyst active A/F control Not operating
Time after heater ON 10 seconds or more
Learned heater OFF current operation Complete

P0141 and P0161
Monitor runs whenever following DTCs not stored P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058 (Rear oxygen sensor heater)
P101D, P102D, P103D, P105D (Air fuel ratio sensor heater)
Battery voltage 10.5 V or higher
Fuel cut OFF
Time after fuel cut ON to OFF 30 seconds or more
Accumulated heater ON time 100 seconds or more
Learned heater OFF current operation Complete
Duration that rear heated oxygen sensor impedance is less than 15 kΩ 2 seconds or more
Heated oxygen sensor heater circuit failure (P0037, P0038, P0057, P0058, P102D and P105D) Not detected

P102D and P105D
Monitor runs whenever following DTCs not stored P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058 (Rear oxygen sensor heater)
Battery voltage 10.5 V or higher
Engine Running
Starter OFF
Catalyst active A/F control Not operating
Time after heater ON 10 seconds or more
Learned heater OFF current operation Complete
Heated oxygen sensor heater circuit failure (P0037, P0038, P0057 and P0058) Not detected

TYPICAL MALFUNCTION THRESHOLDS

P0037 and P0057 (Case 1)
Heater current - Learned heater OFF current 0.3 A or less

P0037 and P0057 (Case 2)
Heated oxygen sensor heater ON current 1 A or less

P0038 and P0058
Hybrid IC high current limiter monitor Fail
Heated oxygen sensor heater output ON

P0141 and P0161
Accumulated heater resistance Varies with sensor element temperature (Example: Higher than 23 Ω)

P102D and P105D
Heated oxygen sensor heater ON current Higher than 1 A

COMPONENT OPERATING RANGE

Heated Oxygen (HO2) sensor heater current 0.4 to 1 A (when engine idles, HO2 sensor warmed up and battery voltage 11 to 14 V)

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

A198819E30
0.749,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 0.946,1.739 1.352,1.900 0.406,0.161 10 Idling 0.211,2.006 1.378,2.344 1.167,0.338 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.622 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.613,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0057, P0058, P0141, or P0161.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.



14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
U152973E01
0.048,0 2.419,0.350 2.371,0.350 10 Front view of wire harness connector: (to HO2 Sensor) 0.277,1.541 0.557,1.722 0.280,0.181 10 D17 0.706,1.507 0.971,1.688 0.264,0.181 10 *1 0.277,1.876 0.583,2.057 0.306,0.181 10 D18 0.706,1.842 0.971,2.023 0.264,0.181 10 *2 0.08,2.556 1.081,2.737 1.001,0.181 10 *1: for Bank 1 0.08,2.94 1.102,3.121 1.022,0.181 10 *2: for Bank 2 2.442,1.439 2.706,1.620 0.264,0.181 10 +B 1.996,1.794 2.365,1.509 false

a.

Disconnect the D17 or D18 HO2 sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D17-2 (+B) - Body ground Ignition switch ON 11 to 14 V
D18-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Result
Result Proceed to
NG A
OK B



A

3.INSPECT INTEGRATION RELAY (EFI MAIN)

B

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
3.INSPECT INTEGRATION RELAY (EFI MAIN)
a.

Remove the integration relay from the engine room relay block (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).


b.

Inspect the EFI NO. 1 fuse.

i.

Remove the EFI NO. 1 fuse from the integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
EFI NO. 1 fuse Always Below 1 Ω



iii.

Reinstall the EFI NO. 1 fuse.



U151425E02
0.104,0.115 2.615,0.479 2.51,0.365 10 false Component without harness connected: (Integration Relay) 0.49,2.417 0.75,2.594 0.26,0.177 10 false 1C 1.365,2.406 1.583,2.583 0.219,0.177 10 false 1B 2.438,2.406 2.688,2.604 0.25,0.198 10 false 1A

c.

Inspect the EFI MAIN relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 When no battery voltage applied to terminals 1B-2 and 1B-3 10 kΩ or higher
When battery voltage applied to terminals 1B-2 and 1B-3 Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY)

NG

REPLACE INTEGRATION RELAY (EFI MAIN)

4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY)
a.

Check the EFI NO. 2 fuse.

i.

Remove the EFI NO. 2 fuse from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
EFI NO. 2 fuse Always Below 1 Ω



iii.

Reinstall the EFI NO. 2 fuse.



b.

Disconnect the D17 or D18 HO2 sensor connector.


c.

Remove the integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D17-2 (+B) - 1B-4 Always Below 1 Ω
D18-2 (+B) - 1B-4 Always Below 1 Ω
D17-2 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
D18-2 (+B) or 1B-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
a.

Disconnect the D17 or D18 HO2 sensor connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D17-1 (HT1B) - D56-45 (HT1B) Always Below 1 Ω
D18-1 (HT2B) - D56-44 (HT2B) Always Below 1 Ω
D17-1 (HT1B) or D56-45 (HT1B) - Body ground Always 10 kΩ or higher
D18-1 (HT2B) or D56-44 (HT2B) - Body ground Always 10 kΩ or higher




OK

6.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the output pending DTCs.

Result
Result Proceed to
No DTC is output A
P0037, P0038, P0057, P0058, P0141, P0161, P102D and/or P105D are output B



A

B