Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A115899E83
0.427,1.031 1.323,1.563 0.896,0.531 10 false from Wheel Speed Sensor 1.802,1.948 3.021,2.156 1.219,0.208 10 false Skid Control ECU 3.729,1.958 5.083,2.188 1.354,0.229 10 false Combination Meter 2.865,0.604 3.896,0.792 1.031,0.188 10 false 4-pulse Signal 4.813,0.604 5.792,0.802 0.979,0.198 10 false 4-pulse Signal 6.031,1.333 6.458,1.542 0.427,0.208 10 false ECM

DTC Code DTC Detection Condition Trouble Area
P0500 While vehicle being driven, no vehicle speed sensor signal transmitted to ECM
(2 trip detection logic)
·

Open or short in speed signal circuit

·

Wheel speed sensor

·

Combination meter

·

ECM

·

Skid control ECU



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.


MONITOR STRATEGY

Related DTCs P0500: Vehicle speed sensor "A" pulse input error
Required Sensors/Components (Main) Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU
Required Sensors/Components (Related) Park / Neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor, Throttle Position (TP) sensor and Mass Air Flow (MAF) meter
Frequency of Operation Continuous
Duration 5 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Time after ignition switch off to ON 3 seconds or more
Vehicle speed 9 km/h (5.6 mph) or more
Battery voltage 8 V or more
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No signal

CONFIRMATION DRIVING PATTERN

A198825E01
0.657,0.826 1.855,1.052 1.198,0.225 10 24 km/h (15 mph) 1.421,1.996 1.820,2.166 0.399,0.170 10 Idling 0.629,2.346 1.827,2.523 1.198,0.177 10 Ignition Switch ON 2.387,2.221 2.620,2.390 0.232,0.169 10 [A] 4.706,0.42 4.911,0.590 0.205,0.170 10 [B] 6.249,3.234 6.447,3.432 0.198,0.198 10 [C] 3.72,2.965 5.636,3.110 1.916,0.145 10 Total of 30 seconds or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0500.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


14.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A244852E03
0.345,2.7 1.811,2.886 1.466,0.186 10 Skid Control ECU 2.469,1.636 2.662,1.801 0.193,0.165 10 36 1.484,1.692 1.607,1.857 0.123,0.165 10 3 4.309,1.552 4.502,1.717 0.193,0.165 10 35 5.291,1.552 5.484,1.717 0.193,0.165 10 13 6.316,1.29 6.604,1.455 0.288,0.165 10 5 V 5.575,1.639 5.916,1.805 0.341,0.165 10 SPD 1.097,1.795 1.438,1.960 0.341,0.165 10 SP1 6.052,2.544 6.405,2.710 0.353,0.165 10 ECM 2.768,1.72 2.961,1.885 0.193,0.165 10 SI 4.017,1.636 4.209,1.801 0.193,0.165 10 +S 2.874,2.623 4.086,2.788 1.213,0.165 10 Combination Meter 2.427,1.802 2.769,1.968 0.341,0.165 10 H37 4.266,1.718 4.608,1.883 0.341,0.165 10 H37 5.247,1.716 5.588,1.881 0.341,0.165 10 A27 5.525,2.887 6.738,3.053 1.213,0.165 10 to Other ECUs 0.34,2.869 1.387,3.055 1.047,0.186 10 (Brake Actuator) 0.358,2.532 0.699,2.698 0.341,0.165 10 A19

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING TECHSTREAM (VEHICLE SPD)

NG

2.READ VALUE USING TECHSTREAM (VEHICLE SPD)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the Techstream.

OK:

Vehicle speeds displayed on Techstream and speedometer display are equal.




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the H37 combination meter connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
H37-35 (+S) - A27-13 (SPD) Always Below 1 Ω
H37-35 (+S) or A27-13 (SPD) - Body ground Always 10 kΩ or higher




OK

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
a.

Disconnect the H37 combination meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
H37-35 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V




OK

5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.

Move the shift lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
H37-35 (+S) - Body ground
·

Ignition switch ON

·

Wheel is turned slowly


Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

REPLACE ECM

NG

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
a.

Move the shift lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
H37-36 (SI) - Body ground
·

Ignition switch ON

·

Wheel is turned slowly


Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR)
a.

Disconnect the combination meter connector.


b.

Disconnect the brake actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
H37-36 (SI) - A19-3 (SP1) Always Below 1 Ω
H37-36 (SI) - or A19-3 (SP1) - Body ground Always 10 kΩ or higher




OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

END