Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  EVAP System  


RELATED DTCS

DTC Monitoring Item See page
P043E Reference orifice clogged (built into canister pump module) (Click here)
P043F Reference orifice high-flow (built into canister pump module)
P0441
·

Purge VSV (Vacuum Switching Valve) stuck closed

·

Purge VSV stuck open

·

Purge flow


(Click here)
P0451
·

Canister pressure sensor (built into canister pump module) noise

·

Canister pressure sensor (built into canister pump module) signal becomes fixed/flat


(Click here)
P0452 Canister pressure sensor (built into canister pump module) voltage low
P0453 Canister pressure sensor (built into canister pump module) voltage high
P0455 EVAP gross leak (Click here)
P0456 EVAP small leak
P2401 Leak detection pump stuck OFF (built into canister pump module) (Click here)
P2402 Leak detection pump stuck ON (built into canister pump module)
P2419 Vent valve stuck closed (built into canister pump module) (Click here)
P2420 Vent valve stuck open (vent) (built into canister pump module) (Click here)
P2610 Soak timer (built into ECM) (Click here)

If any EVAP system DTCs are set, the malfunctioning area can be determined using the table below.

A235785E17
2.865,0.313 3.385,0.542 0.521,0.229 10 false P0441 2.365,0.208 2.885,0.438 0.521,0.229 10 false P043E 2.365,0.458 2.885,0.688 0.521,0.229 10 false P043F 1.74,0.271 2.271,0.583 0.531,0.313 10 false DTCs 3.365,0.323 3.885,0.552 0.521,0.229 10 false P0451 3.813,0.323 4.333,0.552 0.521,0.229 10 false P0452 4.302,0.333 4.823,0.563 0.521,0.229 10 false P0453 4.781,0.333 5.302,0.563 0.521,0.229 10 false P0455 5.26,0.333 5.781,0.563 0.521,0.229 10 false P0456 5.719,0.219 6.24,0.448 0.521,0.229 10 false P2401 5.719,0.469 6.24,0.698 0.521,0.229 10 false P2402 6.198,0.333 6.635,0.542 0.438,0.208 10 false P2419 6.677,0.344 7.135,0.531 0.458,0.188 10 false P2420 0.135,0.885 2.021,1.083 1.885,0.198 10 false Reference orifice clogged 0.125,1.219 2.01,1.417 1.885,0.198 10 false Reference orifice high-flow 0.115,1.51 2,1.708 1.885,0.198 10 false Purge VSV stuck open 0.115,1.833 2,2.031 1.885,0.198 10 false Purge VSV stuck closed 0.104,2.188 2.073,2.542 1.969,0.354 10 false Canister pressure sensor signal fixed 0.115,2.833 2.104,3.167 1.99,0.333 10 false Canister pressure sensor signal noise 0.125,3.49 1.938,3.854 1.813,0.365 10 false Canister pressure sensor low output 0.104,4.135 1.979,4.49 1.875,0.354 10 false Canister pressure sensor high output 0.115,4.792 2,4.99 1.885,0.198 10 false Gross leak 0.115,5.104 2,5.302 1.885,0.198 10 false Small leak 0.094,5.427 2.146,5.625 2.052,0.198 10 false Leak detection pump stuck OFF 0.115,5.729 2.094,5.927 1.979,0.198 10 false Leak detection pump stuck ON 0.125,6.052 2.01,6.25 1.885,0.198 10 false Vent valve stuck closed 0.125,6.365 2.063,6.563 1.938,0.198 10 false Vent valve stuck open (vent) 0.073,0.531 1.698,0.823 1.625,0.292 10 false Malfunctioning Areas

NOTICE:

If the reference pressure difference between the first and second checks is greater than the specification, all the DTCs relating to the reference pressure (P043E, P043F, P2401, P2402 and P2419) are stored.


DESCRIPTION

A312839E04
2.26,2.208 2.573,0.615 2.573,0.615 2.823,0.615 false 0.74,3.323 0.365,3.427 0.365,3.427 0.25,3.698 false 2.844,3.583 2.677,4.24 2.677,4.24 2.542,4.24 false 3.292,5.271 2.927,5.625 2.927,5.625 2.646,5.625 false 5.063,2.698 5.583,2.177 5.583,2.177 5.729,2.177 false 5.292,6.708 5.448,6.844 5.448,6.844 5.594,6.844 false 3.25,7.323 3.01,7.625 3.01,7.625 3.01,7.906 false 3.063,7.271 1.625,7.792 1.625,7.792 1.625,7.948 false 3.927,7.031 3.49,6.594 3.49,6.594 3.229,6.594 false 0.177,0.063 3.365,0.25 3.188,0.188 10 false Location of EVAP (Evaporative Emission) System 2.865,0.552 3.656,0.719 0.792,0.167 10 false Purge VSV 0.052,3.719 2.417,3.885 2.365,0.167 10 false Purge Line Hose (to Intake Manifold) 0.458,4.167 2.542,4.333 2.083,0.167 10 false Purge Line Hose (from Canister) 5.688,6.76 6.99,6.969 1.302,0.208 10 false Canister Assembly 2.927,7.938 4.219,8.469 1.292,0.531 10 false Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) 0.938,7.99 2.552,8.198 1.615,0.208 10 false Fuel Tank Cap Assembly 5.76,2.104 6.417,2.271 0.656,0.167 10 false Fuel Tank 1.875,5.552 2.646,5.719 0.771,0.167 10 false Purge Line 2.292,6.469 3.24,6.635 0.948,0.167 10 false Bleeding Pipe

A240244E07
1.938,0.313 1.802,0.313 1.802,0.313 1.833,0.969 false 1.323,1.594 1.896,1.333 false 3.51,2.771 3.833,2.833 false 2.948,0.677 3.615,0.344 false 4.344,2.99 5.49,2.917 false 4.99,0.917 5.354,0.708 false 3.313,1.542 4.198,1.188 4.198,1.188 5.563,1.188 false 0.042,0.042 1.771,0.313 1.729,0.271 12 false EVAP System Circuit: 0.125,0.74 1.177,0.948 1.052,0.208 10 false Intake Manifold 0.552,1.552 1.302,1.76 0.75,0.208 10 false Purge VSV 5.531,2.844 6.531,3.052 1,0.208 10 false Roll-Over Valve 3.167,3.188 4.021,3.406 0.854,0.219 10 false Fuel Tank 2.563,1.771 3.167,2.115 0.604,0.344 10 true Canister 1.979,0.229 2.885,0.438 0.906,0.208 10 false Throttle Valve 3.667,0.25 4.438,0.458 0.771,0.208 10 false Air Cleaner 5.406,0.615 6.688,0.823 1.281,0.208 10 false Soak Timer 5.635,1.094 7.125,1.302 1.49,0.208 10 false Canister Pump Module 6.177,1.719 6.802,1.917 0.625,0.198 10 false Fuel Cap 2.635,2.677 3.542,2.885 0.906,0.208 10 false Cut-off Valve 4.167,1.656 5.125,1.865 0.958,0.208 10 false Canister Filter 4.313,0.729 4.677,0.938 0.365,0.208 10 false ECM

NOTICE:

In this vehicle's EVAP system, turning ON the vent valve does not seal off the EVAP system. To check for leaks in the EVAP system, disconnect the air inlet vent hose and apply pressure from the atmospheric side of the canister.


While the engine is running, if a predetermined condition (closed-loop, etc.) is met, the purge VSV is opened by the ECM and stored fuel vapors in the canister are purged into the intake manifold. The ECM changes the duty cycle ratio of the purge VSV to control purge flow volume.

The purge flow volume is also determined by the intake manifold pressure. Atmospheric pressure is allowed into the canister through the vent valve to ensure that the purge flow is maintained when the negative pressure (vacuum) is applied to the canister.

The following two monitors run to confirm the appropriate EVAP system operation.

Key-off monitor


This monitor checks for EVAP (Evaporative Emission) system leaks and canister pump module malfunctions. The monitor starts 5 hours* after the ignition switch is turned off. At least 5 hours are required for the fuel to cool down to stabilize the EVAP pressure, thus making the EVAP system monitor more accurate.

The leak detection pump creates negative pressure (vacuum) in the EVAP system and the pressure is measured. Finally, the ECM monitors for leaks from the EVAP system, and malfunctions in both the canister pump module and purge VSV, based on the EVAP pressure.

HINT:

*: If the engine coolant temperature is not below 35°C (95°F) 5 hours after the ignition switch is turned off, the monitor check starts 2 hours later. If it is still not below 35°C (95°F) 7 hours after the ignition switch is turned off, the monitor check starts 2.5 hours later.



Purge flow monitor


The purge flow monitor consists of 2 monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.

·

The 1st monitor

While the engine is running and the purge VSV (Vacuum Switching Valve) is ON (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If negative pressure is not created, the ECM begins the 2nd monitor.

·

The 2nd monitor

The vent valve is turned ON (closed) and the EVAP pressure is measured. If the variation in the pressure is less than 0.4 kPa-g (3.0 mmHg-g), the ECM interprets this as the purge VSV being stuck closed, and illuminates the MIL and sets DTC P0441 (2 trip detection logic).



Atmospheric pressure check:

In order to ensure reliable malfunction detection, the variation between the atmospheric pressures, before and after conduction of the purge flow monitor, is measured by the ECM.

A240245E08
4.208,0.792 4.531,2.583 false 4.469,0.323 4.625,0.323 4.625,0.323 5,2.271 false 2.865,3.271 2.948,3.177 false 3.625,3.656 4.219,2.917 false 5.188,3.021 5.708,3.302 false 0.906,3.938 0.99,3.74 false 4.208,0.792 4.156,0.792 false 0.083,0.083 1.604,0.333 1.521,0.25 12 false EVAP Purge Flow: 1.729,0.625 2.354,0.833 0.625,0.208 10 false Fuel Cap 2.5,0.688 4.167,0.896 1.667,0.208 10 false Canister Pressure Sensor 2.656,0.229 4.49,0.438 1.833,0.208 10 false Reference Orifice (0.02 inch) 5.771,3.281 7.042,3.49 1.271,0.208 10 false Vent Valve (OFF) 5.01,3.823 6.542,4.031 1.531,0.208 10 false Canister Pump Module 1.938,3.219 2.854,3.427 0.917,0.208 10 false Canister Filter 3,1.75 3.667,1.958 0.667,0.208 10 false Fuel Tank 0.521,3.969 1.323,4.177 0.802,0.208 10 false Soak Timer 0.302,2.979 1.469,3.188 1.167,0.208 10 false to Intake Manifold 0.719,3.375 1.115,3.583 0.396,0.208 10 false ECM 1.833,3.583 3.646,3.802 1.813,0.219 10 false Leak Detection Pump (OFF) 1.177,1.563 1.896,1.917 0.719,0.354 10 false Purge VSV (ON) 5.719,1.917 6.333,2.115 0.615,0.198 10 false Canister

Component Operation
Canister Contains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank.
Cut-off valve Located in fuel tank. Valve floats and closes when fuel tank 100% full.
Purge VSV (Vacuum Switching Valve) Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake manifold controlled by purge VSV duty cycle ratio (current-carrying time) (Open: ON; Closed: OFF).
Roll-over valve Located in fuel tank. Valve closed by its own weight when vehicle overturns to prevent fuel from spilling out.
Soak timer Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+/-15 min) after ignition switch turned off. This allows fuel to cool down, stabilizing EVAP pressure. When approximately 5 hours elapsed, ECM activates (refer to fig. 3).
Canister pump module Consists of (a) to (d) below. Canister pump module cannot be disassembled.
(a) Vent valve Vents and closes EVAP system. When ECM turns valve ON, EVAP system closed. When ECM turns valve OFF, EVAP system vented. Negative pressure (vacuum) created in EVAP system to check for EVAP leaks by closing purge VSV, turning on vent valve (closed) and operating leak detection pump (refer to fig. 1).
(b) Canister pressure sensor Indicates pressure as voltages. ECM supplies regulated 5 V to canister pressure sensor, and uses feedback from sensor to monitor EVAP system pressure (refer to fig. 2).
(c) Leak detection pump Creates negative pressure (vacuum) in EVAP system for leak check.
(d) Reference orifice Has opening with 0.02 inch diameter. Vacuum produced through orifice by closing purge VSV, turning off vent valve and operating leak detection pump, to monitor reference pressure. Reference pressure indicates small leak of EVAP.

A115902E37
3.25,1.76 2.719,2.865 false 5.385,1.823 4.948,2.792 false 6.271,1.76 5.99,2.823 false 2.844,1.875 2.844,2.146 2.844,2.146 1.604,2.833 false 1.271,0.896 2.188,1.365 false 2.344,2.177 1.375,2.271 false 0.073,0.052 2.531,0.313 2.458,0.26 12 false Canister Pump Module (fig. 1): 1.021,1.448 1.771,1.615 0.75,0.167 10 false Canister 0.417,2.76 1.604,3.146 1.188,0.385 10 false Canister Pressure Sensor 0.24,2.188 1.354,2.552 1.115,0.365 10 false Reference Orifice (0.02 Inch) 4.063,0.094 4.698,0.26 0.635,0.167 10 false : Airflow 5.156,0.458 6.99,0.625 1.833,0.167 10 false Condition: Leak Check 3.135,2.49 4.104,2.833 0.969,0.344 10 false from Refueling Valve 2.073,2.875 3.073,3.229 1,0.354 10 false Leak Detection Pump: OFF 3.865,0.906 4.74,1.438 0.875,0.531 10 false to Canister Filter (Atmosphere) 5.615,2.854 6.625,3.208 1.01,0.354 10 false Leak Detection Pump: ON 2.01,0.458 3.833,0.625 1.823,0.167 10 false Condition: Purge Flow 4.323,2.813 5.333,3.188 1.01,0.375 10 false Vent Valve: ON (closed) 0.188,0.76 1.25,1.167 1.063,0.406 10 false Vent Valve: OFF (vent)

A311003E07
5.042,1.115 4.667,1.563 false 5.052,2.927 4.667,3.448 false 0.156,0.135 3.24,0.333 3.083,0.198 10 false Canister Pressure Sensor Specification (fig. 2): 1.813,1.594 2.375,1.792 0.563,0.198 10 false 4.900 V 1.813,2.083 2.375,2.281 0.563,0.198 10 false 4.423 V 1.813,2.781 2.375,2.979 0.563,0.198 10 false 1.425 V 1.813,3.26 2.375,3.458 0.563,0.198 10 false 0.450 V 1.375,1.052 2.375,1.25 1,0.198 10 false Output Voltage 5.031,3.427 5.677,3.625 0.646,0.198 10 false Pressure 5.094,1.021 6.188,1.219 1.094,0.198 10 false Malfunction Area 5.094,2.865 6.188,3.063 1.094,0.198 10 false Malfunction Area 3.031,3.656 3.313,3.833 0.281,0.177 10 false 60 3.719,3.646 4.052,3.854 0.333,0.208 10 false 115 4.406,3.646 4.906,3.823 0.5,0.177 10 false kPa-a 4.146,2.323 5.094,2.521 0.948,0.198 10 false Usable Range 1.219,4.313 5.115,4.51 3.896,0.198 10 false Standard atmospheric pressure is 101.3 kPa-a (760 mmHg-a) 1.219,4.094 1.646,4.292 0.427,0.198 10 false HINT: 2.979,3.813 3.396,4.01 0.417,0.198 10 false (450) 3.698,3.792 4.094,4 0.396,0.208 10 false (862) 4.375,3.792 5.073,4 0.698,0.208 10 false (mmHg-a)

U151545E01
5.59,4.253 5.936,4.409 0.346,0.156 10 ECM 4.992,1.164 5.731,1.481 0.739,0.317 10 Soak Timer IC 5.029,2.544 5.671,2.876 0.642,0.332 10 Power Source IC 5.002,3.347 5.732,3.670 0.730,0.323 10 Main Relay Control IC 4.324,0.9 4.724,1.056 0.400,0.156 10 IGSW 4.523,2.697 4.739,2.848 0.216,0.151 10 +B 4.303,3.492 4.736,3.649 0.434,0.157 10 MREL 3.175,3.893 3.433,4.049 0.258,0.156 10 EFI 1.895,3.314 2.542,3.470 0.647,0.156 10 EFI NO. 1 0.55,3.875 1.021,4.058 0.471,0.184 10 Battery 1.419,2.343 2.066,2.508 0.647,0.165 10 IG2 MAIN 0.373,2.33 0.705,2.485 0.332,0.156 10 AM2 3.908,1.105 4.194,1.270 0.286,0.165 10 IGN 2.837,1.698 3.095,1.864 0.258,0.165 10 IG2 1.428,1.67 2.371,1.845 0.943,0.174 10 Ignition Switch 0.065,0.087 2.045,0.308 1.980,0.221 12 Soak Timer Circuit (fig. 3):

WIRING DIAGRAM

A244835E02
5.884,7.066 6.221,7.222 0.336,0.156 10 ECM 5.443,0.596 5.891,0.752 0.448,0.156 10 MPMP 5.1,0.606 5.381,0.775 0.281,0.170 10 A27 5.1,3.282 5.381,3.451 0.281,0.170 10 A27 5.1,6.106 5.381,6.276 0.281,0.170 10 A27 5.156,0.442 5.340,0.598 0.184,0.156 10 49 5.436,1.591 5.856,1.750 0.420,0.159 10 VCV1 5.1,1.689 5.388,1.852 0.288,0.163 10 D56 5.149,1.514 5.346,1.684 0.198,0.170 10 67 5.436,2.067 5.870,2.223 0.434,0.156 10 PPMP 5.106,1.969 5.366,2.132 0.260,0.163 10 121 5.1,2.151 5.395,2.307 0.295,0.156 10 D56 5.1,2.608 5.395,2.764 0.295,0.156 10 D56 5.1,4.196 5.395,4.352 0.295,0.156 10 D56 5.436,2.53 5.870,2.686 0.434,0.156 10 ETHW 5.151,2.437 5.336,2.592 0.185,0.156 10 97 5.436,3.286 5.873,3.446 0.437,0.159 10 VPMP 5.15,3.118 5.347,3.274 0.198,0.156 10 30 5.442,4.203 5.803,4.362 0.361,0.159 10 PRG 5.148,4.035 5.359,4.191 0.211,0.156 10 63 5.436,6.013 5.870,6.169 0.434,0.156 10 MREL 5.152,5.932 5.343,6.081 0.191,0.149 10 34 1.457,0.504 1.919,0.660 0.461,0.156 10 MGND 1.279,0.52 1.393,0.690 0.114,0.170 10 4 2.9,0.504 3.334,0.660 0.434,0.156 10 MTRB 3.37,0.516 3.484,0.672 0.114,0.156 10 3 1.642,3.691 2.041,3.847 0.399,0.156 10 O24 1.642,3.843 3.090,4.027 1.448,0.184 10 Canister Pump Module 1.707,0.792 3.085,0.976 1.378,0.184 10 Leak Detection Pump 1.45,2.845 3.078,3.015 1.628,0.170 10 Canister Pressure Sensor 2.046,3.407 2.743,3.577 0.698,0.170 10 Vent Valve 2.998,1.598 3.328,1.754 0.330,0.156 10 VCC 3.37,1.591 3.498,1.759 0.128,0.167 10 6 2.9,2.041 3.334,2.196 0.434,0.156 10 VOUT 3.37,2.05 3.485,2.206 0.114,0.156 10 7 2.9,2.733 3.348,2.889 0.448,0.156 10 SGND 3.377,2.513 3.477,2.669 0.100,0.156 10 8 2.886,3.197 3.334,3.367 0.448,0.170 10 VGND 1.443,3.195 1.835,3.351 0.392,0.156 10 VLVB 1.283,3.195 1.397,3.365 0.114,0.170 10 5 3.377,3.195 3.484,3.351 0.107,0.156 10 1 3.943,4.467 4.252,4.623 0.309,0.156 10 D16 3.943,4.605 4.683,4.761 0.739,0.156 10 Purge VSV 3.813,4.034 3.928,4.204 0.114,0.170 10 1 4.6,4.038 4.714,4.208 0.114,0.170 10 2 3.678,6.856 4.778,7.040 1.100,0.184 10 Integration Relay 1.408,5.374 2.064,5.544 0.656,0.170 10 EFI NO. 2 2.557,5.893 3.213,6.062 0.656,0.170 10 EFI NO. 1 3.482,6.417 4.112,6.573 0.630,0.156 10 EFI MAIN 2.238,5.756 2.456,5.923 0.218,0.166 10 1C 2.296,5.584 2.411,5.740 0.114,0.156 10 1 1.464,6.611 1.953,6.795 0.489,0.184 10 Battery 2.249,5.262 2.464,5.414 0.215,0.152 10 1B 2.725,6.663 2.940,6.816 0.215,0.152 10 1B 4.525,6.108 4.740,6.260 0.215,0.152 10 1B 2.293,5.096 2.407,5.258 0.114,0.162 10 4 4.574,5.937 4.689,6.106 0.114,0.170 10 2 2.527,6.663 2.641,6.819 0.114,0.156 10 3

CONFIRMATION DRIVING PATTERN

HINT:

After a repair, check Monitor Status by performing the Key-Off Monitor Confirmation and Purge Flow Monitor Confirmation described below.


KEY-OFF MONITOR CONFIRMATION


a.

Preconditions

The monitor will not run unless:

·

The vehicle has been driven for 10 minutes or more (in a city area or on a freeway)

·

The fuel tank is less than 90% full

·

The altitude is less than 2438 m (8000 ft.)

·

The Engine Coolant Temperature (ECT) is between 4.4°C and 35°C (40°F and 95°F)

·

The Intake Air Temperature (IAT) is between 4.4°C and 35°C (40°F and 95°F)

·

The vehicle remains stationary (the vehicle speed is 0 km/h [0 mph])



b.

Monitor Conditions

1.

Allow the engine to idle for at least 5 minutes.

2.

Turn the ignition switch off and wait for 6 hours (8 or 10.5 hours).

HINT:

Do not start the engine until checking Monitor Status. If the engine is started, the steps described above must be repeated.




c.

Monitor Status

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Evaporative System.

4.

Check the Monitor Status displayed on the Techstream.

HINT:

If Incomplete is displayed, the monitor is not complete. Make sure that the preconditions have been met, and perform the Monitor Conditions again.





PURGE FLOW MONITOR CONFIRMATION (P0441)


HINT:

Perform this monitor confirmation after the Key-Off Monitor Confirmation shows Complete.


a.

Preconditions

The monitor will not run unless:

·

The vehicle has been driven for 10 minutes or more (in a city area or on a freeway)

·

The ECT is between 4.4 and 35°C (40 and 95°F)

·

The IAT is between 4.4 and 35°C (40 and 95°F)



b.

Monitor Conditions

1.

Release the pressure from the fuel tank by removing and reinstalling the fuel cap.

2.

Warm the engine up until the ECT reaches more than 75°C (167°F).

3.

Increase the engine speed to 3000 rpm once.

4.

Allow the engine to idle and turn A/C ON for 1 minute.



c.

Monitor Status

1.

Turn the ignition switch off (if ON or the engine is running).

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Monitor.

5.

Check the Monitor Status displayed on the Techstream.

HINT:

If Incomplete is displayed, the monitor is not complete. Make sure that the preconditions have been met, and perform the Monitor Conditions again.





MONITOR RESULT

CAUTION / NOTICE / HINT

NOTICE:

The Techstream is required to conduct the following diagnostic troubleshooting procedure.


HINT:
·

Using Techstream monitor results enables the EVAP (Evaporative Emission) system to be confirmed.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CONFIRM DTC
a.

Turn the ignition switch off and wait for 10 seconds.


b.

Turn the ignition switch to ON.


c.

Turn the ignition switch off and wait for 10 seconds.


d.

Connect the Techstream to the DLC3.


e.

Turn the ignition switch to ON and turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm DTCs and freeze frame data.

If any EVAP system DTCs are set, the malfunctioning area can be determined using the table below.


A235785E17
2.865,0.313 3.385,0.542 0.521,0.229 10 false P0441 2.365,0.208 2.885,0.438 0.521,0.229 10 false P043E 2.365,0.458 2.885,0.688 0.521,0.229 10 false P043F 1.74,0.271 2.271,0.583 0.531,0.313 10 false DTCs 3.365,0.323 3.885,0.552 0.521,0.229 10 false P0451 3.813,0.323 4.333,0.552 0.521,0.229 10 false P0452 4.302,0.333 4.823,0.563 0.521,0.229 10 false P0453 4.781,0.333 5.302,0.563 0.521,0.229 10 false P0455 5.26,0.333 5.781,0.563 0.521,0.229 10 false P0456 5.719,0.219 6.24,0.448 0.521,0.229 10 false P2401 5.719,0.469 6.24,0.698 0.521,0.229 10 false P2402 6.198,0.333 6.635,0.542 0.438,0.208 10 false P2419 6.677,0.344 7.135,0.531 0.458,0.188 10 false P2420 0.135,0.885 2.021,1.083 1.885,0.198 10 false Reference orifice clogged 0.125,1.219 2.01,1.417 1.885,0.198 10 false Reference orifice high-flow 0.115,1.51 2,1.708 1.885,0.198 10 false Purge VSV stuck open 0.115,1.833 2,2.031 1.885,0.198 10 false Purge VSV stuck closed 0.104,2.188 2.073,2.542 1.969,0.354 10 false Canister pressure sensor signal fixed 0.115,2.833 2.104,3.167 1.99,0.333 10 false Canister pressure sensor signal noise 0.125,3.49 1.938,3.854 1.813,0.365 10 false Canister pressure sensor low output 0.104,4.135 1.979,4.49 1.875,0.354 10 false Canister pressure sensor high output 0.115,4.792 2,4.99 1.885,0.198 10 false Gross leak 0.115,5.104 2,5.302 1.885,0.198 10 false Small leak 0.094,5.427 2.146,5.625 2.052,0.198 10 false Leak detection pump stuck OFF 0.115,5.729 2.094,5.927 1.979,0.198 10 false Leak detection pump stuck ON 0.125,6.052 2.01,6.25 1.885,0.198 10 false Vent valve stuck closed 0.125,6.365 2.063,6.563 1.938,0.198 10 false Vent valve stuck open (vent) 0.073,0.531 1.698,0.823 1.625,0.292 10 false Malfunctioning Areas

NOTICE:

If the reference pressure difference between the first and second checks is greater than the specification, all the DTCs relating to the reference pressure (P043E, P043F, P2401, P2402 and P2419) are stored.



NEXT

2.PERFORM EVAP SYSTEM CHECK (AUTO OPERATION)
2.PERFORM EVAP SYSTEM CHECK (AUTO OPERATION)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the temperature below 35°C (95°F).




b.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.


c.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


HINT:

If no pending DTCs are displayed, perform the MONITOR CONFIRMATION (see "Diagnostic Help" menu). After this confirmation, check for pending DTCs. If no DTCs are displayed, the EVAP system is normal.



NEXT

3.PERFORM EVAP SYSTEM CHECK (MANUAL OPERATION)
3.PERFORM EVAP SYSTEM CHECK (MANUAL OPERATION)
U153103E02
0.99,3.167 1.125,3.427 false 5.25,3.677 5.063,3.385 false 6.125,3.313 5.948,3.042 false 0.406,0.594 1.188,0.802 0.781,0.208 10 false Purge VSV 0.406,1.115 1.208,1.323 0.802,0.208 10 false Vent Valve 0.115,1.385 1.115,1.74 1,0.354 10 false Leak Detection Pump 0.063,1.958 1.177,2.167 1.115,0.208 10 false EVAP Pressure 0.229,2.219 0.938,2.427 0.708,0.208 10 false Positive 0.219,2.51 0.969,2.719 0.75,0.208 10 false Negative 0.031,2.865 1.052,3.229 1.021,0.365 10 false First Reference Pressure 0.448,3.969 0.781,4.135 0.333,0.167 10 false Step 0.125,4.26 1.146,4.469 1.021,0.208 10 false Time (Seconds) 0.25,4.5 1.063,4.708 0.813,0.208 10 false (Reference) 1.615,4.292 1.823,4.5 0.208,0.208 10 false 60 3.698,2.229 4.635,2.438 0.938,0.208 10 false Gross Leak 3.698,2.979 4.635,3.188 0.938,0.208 10 false Small Leak 4.104,3.542 4.833,3.75 0.729,0.208 10 false No Leak 3.323,4.313 4.75,4.479 1.427,0.167 10 false Within 15 minutes 2.469,4.302 2.76,4.5 0.292,0.198 10 false 360 5.104,4.292 5.313,4.5 0.208,0.208 10 false 10 5.667,4.292 5.885,4.5 0.219,0.208 10 false 60 5.135,3.677 6.448,3.885 1.313,0.208 10 true Normal Pressure 6.177,2.969 7.135,3.5 0.958,0.531 10 false [Second Reference Pressure] x 0.2 5.094,3.99 5.354,4.198 0.26,0.208 10 false 4/6 5.646,3.99 5.917,4.198 0.271,0.208 10 false 5/6 3.813,3.99 4.188,4.198 0.375,0.208 10 false 3/6 2.49,3.99 2.865,4.198 0.375,0.208 10 false 2/6 1.625,3.99 2,4.198 0.375,0.208 10 false 1/6 3.865,1.51 4.25,1.719 0.385,0.208 10 false ON 3.865,1 4.25,1.208 0.385,0.208 10 false ON 5.073,0.458 5.458,0.667 0.385,0.208 10 false ON 5.646,0.292 6.583,0.51 0.938,0.219 10 false ON: Open 6.24,0.729 7.125,0.948 0.885,0.219 10 false OFF: Closed 5.677,0.927 6.615,1.146 0.938,0.219 10 false ON: Closed 6.323,1.25 7.063,1.469 0.74,0.219 10 false OFF: Vent 0.052,0.031 1.521,0.417 1.469,0.385 10 true EVAP System Check: 6.552,3.99 6.813,4.198 0.26,0.208 10 false 6/6

NOTICE:
·

In the Evaporative System Check (Manual Mode), perform the series of 5 Evaporative System Check steps manually using the Techstream.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the temperature below 35°C (95°F).




b.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Manual Mode.



NEXT

4.PERFORM EVAP SYSTEM CHECK (STEP 1/6)
4.PERFORM EVAP SYSTEM CHECK (STEP 1/6)
U110367E03
0.979,3.156 1.115,3.417 false 1.76,3 1.656,2.604 false 1.969,1.938 1.771,2.292 false 0.354,0.625 1.167,0.833 0.813,0.208 10 false Purge VSV 0.438,1.135 1.219,1.354 0.781,0.219 10 false Vent Valve 0.156,1.458 1.167,1.802 1.01,0.344 10 false Leak Detection Pump 0.115,1.917 1.208,2.125 1.094,0.208 10 false EVAP Pressure 0.208,2.167 0.938,2.375 0.729,0.208 10 false Positive 0.219,2.552 0.958,2.76 0.74,0.208 10 false Negative 0.031,2.979 1.031,3.344 1,0.365 10 false First Reference Pressure 1.698,3.031 2.052,3.24 0.354,0.208 10 false OK 2,1.792 4.49,2.125 2.49,0.333 10 true Canister Pressure Sensor Signal Noise 1.625,4.333 1.833,4.521 0.208,0.188 10 false 60 3.896,1.542 4.292,1.75 0.396,0.208 10 false ON 3.896,1.042 4.292,1.25 0.396,0.208 10 false ON 5.073,0.479 5.469,0.688 0.396,0.208 10 false ON 1.604,4.063 1.938,4.271 0.333,0.208 10 false 1/6 0.292,3.958 0.74,4.167 0.448,0.208 10 false Steps 0.146,4.198 1.167,4.406 1.021,0.208 10 false Time (Seconds) 0.292,4.458 1.115,4.667 0.823,0.208 10 false (Reference) 5.479,0.385 6.542,0.604 1.063,0.219 10 false ON: Open 6.219,0.729 7.083,0.938 0.865,0.208 10 false OFF: Closed 5.458,0.938 6.458,1.146 1,0.208 10 false ON: Closed 6.229,1.292 6.958,1.5 0.729,0.208 10 false OFF: Vent

a.

Check the EVAP pressure in step 1/6.

Result
DTCs*1 Test Result Suspected Trouble Area Proceed to
- Virtually no variation in EVAP pressure Not yet determined A
P0451 EVAP pressure fluctuates by +/-0.3 kPa-g (+/-2.25 mmHg-g) or more Canister pressure sensor noise B
(P0452 or P0453)*2
·

EVAP pressure is below 42.11 kPa (abs) [315.85 mmHg (abs)] or 123.761 kPa (abs) [928.28 mmHg (abs)] or more

·

EVAP pressure deviates +/-10 kPa [+/-75 mmHg] from actual atmosphere pressure*3


Canister pressure sensor or its circuit has malfunction C

·

*1: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.

·

*2: If the canister pressure sensor circuit has an open or short, DTC P0452 or P0453 is stored 0.5 seconds after the ignition switch is turned to ON.


HINT:

*3: Canister pressure sensor standard output range is 70 to 110 kPa (abs) [525 to 825 mmHg (abs)]. This varies by weather.




A

5.PERFORM EVAP SYSTEM CHECK (STEP 1/6 TO 2/6)

B

38.REPLACE CANISTER PUMP MODULE

C

12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR CIRCUIT)
5.PERFORM EVAP SYSTEM CHECK (STEP 1/6 TO 2/6)
U152957E02
0.979,3.156 1.115,3.417 false 2.688,2.74 2.281,3.448 false 0.375,0.542 1.125,0.76 0.75,0.219 10 false Purge VSV 0.417,0.99 1.135,1.198 0.719,0.208 10 false Vent Valve 0.177,1.302 1.146,1.677 0.969,0.375 10 false Leak Detection Pump 0.125,1.865 1.219,2.073 1.094,0.208 10 false EVAP Pressure 0.25,2.156 0.896,2.365 0.646,0.208 10 false Positive 0.25,2.521 0.958,2.729 0.708,0.208 10 false Negative 0.052,2.917 1.052,3.333 1,0.417 10 false First Reference Pressure 0.448,3.958 0.781,4.135 0.333,0.177 10 false Step 0.115,4.24 1.125,4.448 1.01,0.208 10 false Time (Seconds) 0.281,4.469 1.115,4.677 0.833,0.208 10 false (Reference) 1.615,4.292 1.844,4.5 0.229,0.208 10 false 60 1.615,3.958 1.979,4.177 0.365,0.219 10 false 1/6 2.51,3.958 2.896,4.177 0.385,0.219 10 false 2/6 2.708,2.646 4.781,3.042 2.073,0.396 10 true Leak Detection Pump Stuck ON 3.833,1.49 4.198,1.698 0.365,0.208 10 false ON 3.833,1.021 4.198,1.229 0.365,0.208 10 false ON 5.083,0.448 5.448,0.656 0.365,0.208 10 false ON 6.219,0.354 6.906,0.563 0.688,0.208 10 false ON: Open 6.219,0.708 7.083,0.917 0.865,0.208 10 false OFF: Closed 6.219,0.938 7.094,1.146 0.875,0.208 10 false ON: Closed 6.219,1.25 6.906,1.458 0.688,0.208 10 false OFF: Vent 2.49,4.292 2.802,4.469 0.313,0.177 10 false 360

a.

Check the EVAP pressure in steps 1/6 and 2/6.

Result
DTCs* Test Result Suspected Trouble Area Proceed to
- Virtually no variation in EVAP pressure during step 1/6. Then decreases to reference pressure Not yet determined A
P2402 Small difference between EVAP pressures during steps 1/6 and 2/6 Leak detection pump stuck ON B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.

HINT:

The first reference pressure is the value determined in step 2/6.




A

6.PERFORM EVAP SYSTEM CHECK (STEP 2/6)

B

31.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE)
6.PERFORM EVAP SYSTEM CHECK (STEP 2/6)
U152959E02
1.094,3.156 1.229,3.417 false 3.729,3.167 3.229,3.344 false 3.333,2.635 2.823,2.708 false 3.104,1.823 2.646,2.448 false 2,2.083 2.292,1.792 false 3.51,3.844 2.969,3.875 false 0.302,0.563 1.052,0.792 0.75,0.229 10 false Purge VSV 0.417,1.021 1.156,1.229 0.74,0.208 10 false Vent Valve 0.177,1.302 1.198,1.688 1.021,0.385 10 false Leak Detection Pump 0.115,1.854 1.156,2.063 1.042,0.208 10 false EVAP Pressure 0.198,2.146 1.052,2.354 0.854,0.208 10 false Positive 0.198,2.521 1.052,2.729 0.854,0.208 10 false Negative 0.083,3.052 1.094,3.583 1.01,0.531 10 false First Reference Pressure 1.354,2.052 2.083,2.281 0.729,0.229 10 false 4 seconds 2.573,3.99 2.958,4.208 0.385,0.219 10 false 2/6 3.844,3.99 4.198,4.208 0.354,0.219 10 false 3/6 3.469,4.281 4.896,4.49 1.427,0.208 10 false Within 15 minutes 2.49,4.292 2.771,4.479 0.281,0.188 10 false 360 0.365,3.948 0.729,4.156 0.365,0.208 10 false Step 0.281,4.469 1.167,4.677 0.885,0.208 10 false (Reference) 0.115,4.198 1.135,4.406 1.021,0.208 10 false Time (Seconds) 3.813,3.063 4.208,3.271 0.396,0.208 10 false OK 3.375,2.521 4.979,2.74 1.604,0.219 10 false Vent Valve Stuck Closed 3.146,1.75 5.271,2.333 2.125,0.583 10 true Leak Detection Pump Stuck OFF Reference Orifice High-flow 3.854,1.469 4.208,1.677 0.354,0.208 10 false ON 3.854,0.969 4.208,1.177 0.354,0.208 10 false ON 5.073,0.448 5.427,0.656 0.354,0.208 10 false ON 6.24,0.365 6.917,0.573 0.677,0.208 10 false ON: Open 6.25,0.698 7.094,0.917 0.844,0.219 10 false OFF: Closed 6.271,1.24 6.979,1.469 0.708,0.229 10 false OFF: Vent 6.25,0.938 7.01,1.156 0.76,0.219 10 false ON: Closed 3.552,3.823 5.292,4 1.74,0.177 10 true Reference Orifice Clogged

HINT:

Make a note of the pressures checked in steps (a) and (b) below.


(a) Check the EVAP pressure 4 seconds after the leak detection pump is activated*.

*: The leak detection pump begins to operate as step 1/6 finishes and step 2/6 starts.

(b) Check the EVAP pressure again when it has stabilized. This pressure is the reference pressure.

Result
DTCs* Test Result Suspected Trouble Area Proceed to
- EVAP pressure in step (b) between -4.85 kPa-g and -1.057 kPa-g (-36.4 mmHg-g and -7.93 mmHg-g) Not yet determined A
P043F and P2401 EVAP pressure in step (b) -1.057 kPa-g (-7.93 mmHg-g) or more
·

Reference orifice high-flow

·

Leak detection pump stuck OFF


B
P043E EVAP pressure in step (b) below -4.85 kPa-g (-36.4 mmHg-g) Reference orifice clogged C
P2419 EVAP pressure in step (a) more than -1.057 kPa-g (-7.93 mmHg-g) Vent valve stuck closed D

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.



A

7.PERFORM EVAP SYSTEM CHECK (STEP 2/6 TO 3/6)

B

11.PERFORM EVAP SYSTEM CHECK (STEP 3/6)

C

38.REPLACE CANISTER PUMP MODULE

D

13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
7.PERFORM EVAP SYSTEM CHECK (STEP 2/6 TO 3/6)
U115323E02
0.969,3.135 1.104,3.406 false 3.438,2.719 3.052,3.427 false 0.354,0.583 1.146,0.792 0.792,0.208 10 false Purge VSV 0.396,1.01 1.156,1.219 0.76,0.208 10 false Vent Valve 0.167,1.323 1.208,1.719 1.042,0.396 10 false Leak Detection Pump 0.125,1.865 1.208,2.073 1.083,0.208 10 false EVAP Pressure 0.271,2.125 0.969,2.333 0.698,0.208 10 false Positive 0.25,2.521 1.042,2.729 0.792,0.208 10 false Negative 0.031,2.906 1.031,3.271 1,0.365 10 false First Reference Pressure 0.365,4 0.719,4.208 0.354,0.208 10 false Step 0.719,4.229 1.177,4.438 0.458,0.208 10 false Time 0.229,4.458 1.052,4.677 0.823,0.219 10 false (Reference) 3.823,1.01 4.208,1.219 0.385,0.208 10 false ON 3.813,1.521 4.198,1.729 0.385,0.208 10 false ON 5.073,0.479 5.458,0.688 0.385,0.208 10 false ON 6.292,0.344 7,0.552 0.708,0.208 10 false ON: Open 6.271,0.927 7.083,1.135 0.813,0.208 10 false ON: Closed 6.271,0.708 7.115,0.917 0.844,0.208 10 false OFF: Closed 6.333,1.271 7.094,1.479 0.76,0.208 10 false OFF: Vent 3.49,2.583 4.698,3.042 1.208,0.458 10 false Vent Valve Stuck Open (vent) 3.781,4.01 4.094,4.219 0.313,0.208 10 false 3/6 2.479,4.031 2.802,4.24 0.323,0.208 10 false 2/6 3.406,4.323 4.896,4.531 1.49,0.208 10 false Within 15 minutes

a.

Check the EVAP pressure increase in step 3/6.

Result
DTCs* Test Result Suspected Trouble Area Proceed to
- EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 2/6 to step 3/6 Not yet determined A
P2420 No variation in EVAP pressure despite proceeding from step 2/6 to step 3/6 Vent valve stuck open (vent) B
P0451 No variation in EVAP pressure during steps 1/6 through 3/6 Canister pressure sensor output value stuck C

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.



A

8.PERFORM EVAP SYSTEM CHECK (STEP 3/6)

B

27.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)

C

15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
8.PERFORM EVAP SYSTEM CHECK (STEP 3/6)
U115324E02
0.969,3.135 1.104,3.396 false 0.354,0.552 1.073,0.76 0.719,0.208 10 false Purge VSV 0.406,1.094 1.146,1.313 0.74,0.219 10 false Vent Valve 0.167,1.448 1.188,1.823 1.021,0.375 10 false Leak Detection Pump 0.083,1.958 1.167,2.167 1.083,0.208 10 false EVAP Pressure 0.208,2.24 0.896,2.448 0.688,0.208 10 false Positive 0.208,2.542 0.979,2.75 0.771,0.208 10 false Negative 0.021,2.927 1.042,3.302 1.021,0.375 10 false First Reference Pressure 0.354,4.021 0.719,4.229 0.365,0.208 10 false Step 0.781,4.146 1.177,4.354 0.396,0.208 10 false Time 0.365,4.417 1.188,4.625 0.823,0.208 10 false (Reference) 3.854,1.01 4.219,1.219 0.365,0.208 10 false ON 3.854,1.521 4.219,1.729 0.365,0.208 10 false ON 5.073,0.458 5.438,0.667 0.365,0.208 10 false ON 6.26,0.354 6.969,0.563 0.708,0.208 10 false ON: Open 6.26,0.708 7.135,0.917 0.875,0.208 10 false OFF: Closed 6.26,0.927 7.042,1.135 0.781,0.208 10 false ON: Closed 6.333,1.271 7.063,1.479 0.729,0.208 10 false OFF: Vent 3.823,4.052 4.156,4.26 0.333,0.208 10 false 3/6 3.417,4.302 4.771,4.51 1.354,0.208 10 false Within 15 minutes

a.

Wait until the EVAP pressure change is less than 0.1 kPa-g (0.75 mmHg-g) for 30 seconds.


b.

Measure the EVAP pressure and record it.

HINT:

A few minutes are required for the EVAP pressure to become saturated. When there is little fuel in the fuel tank, it takes up to 15 minutes.




NEXT

9.PERFORM EVAP SYSTEM CHECK (STEP 4/6)
9.PERFORM EVAP SYSTEM CHECK (STEP 4/6)
U115325E02
0.969,3.135 1.104,3.396 false 4.677,2.094 5.177,2.729 false 4.719,3.031 5.167,3.688 false 0.396,0.552 1.156,0.729 0.76,0.177 10 false Purge VSV 0.396,1.125 1.188,1.344 0.792,0.219 10 false Vent Valve 0.156,1.406 1.125,1.771 0.969,0.365 10 false Leak Detection Pump 0.115,1.906 1.219,2.115 1.104,0.208 10 false EVAP Pressure 0.198,2.188 1.083,2.396 0.885,0.208 10 false Positive 0.198,2.521 1.146,2.729 0.948,0.208 10 false Negative 0.354,3.823 1.042,4.031 0.688,0.208 10 false Step 3.125,2.802 4.729,2.99 1.604,0.188 10 false Purge VSV Stuck Closed 5.063,0.49 5.417,0.698 0.354,0.208 10 false ON 3.896,1.021 4.25,1.229 0.354,0.208 10 false ON 3.906,1.531 4.26,1.74 0.354,0.208 10 false ON 0.125,4.24 1.198,4.448 1.073,0.208 10 false Time (Seconds) 0.302,4.479 1.177,4.688 0.875,0.208 10 false (Reference) 4.427,1.917 4.802,2.125 0.375,0.208 10 false OK 5.094,3.823 5.438,4.031 0.344,0.208 10 false 4/6 5.104,4.323 5.406,4.51 0.302,0.188 10 false 10 5.667,0.354 6.604,0.563 0.938,0.208 10 false ON: Open 5.667,0.927 6.677,1.135 1.01,0.208 10 false ON: Closed 6.198,0.719 7.073,0.927 0.875,0.208 10 false OFF: Closed 6.292,1.26 7.073,1.469 0.781,0.208 10 false OFF: Vent 0.052,2.917 1.073,3.26 1.021,0.344 10 false First Reference Pressure

a.

Check the EVAP pressure in step 4/6.

Result
DTCs*1 Test Result Suspected Trouble Area Proceed to
- EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 3/6 to step 4/6 Not yet determined A
P0441*2 EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 3/6 to step 4/6 Problems in purge line between purge VSV and intake manifold B
P0441 Variation in EVAP pressure less than 0.3 kPa-g (2.25 mmHg-g) for 10 seconds, after proceeding from step 3/6 to step 4/6 Purge VSV stuck closed C

·

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.

·

*2: This result suggests that due to purge line blockage or purge VSV malfunction, the DTC was stored by the purge flow monitor while the engine was running, or that key-off monitor test result were nearly borderline values.




A

10.PERFORM EVAP SYSTEM CHECK (STEP 5/6)

B

22.INSPECT EVAP HOSE (PURGE VSV - CANISTER)

C

17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV)
10.PERFORM EVAP SYSTEM CHECK (STEP 5/6)
U113630E03
1.031,3.156 1.177,3.417 false 6.156,2.625 5.979,2.896 false 6.302,3.979 6.125,3.708 false 6.271,0.365 6.948,0.573 0.677,0.208 10 false ON: Open 6.271,0.719 7.115,0.938 0.844,0.219 10 false OFF: Closed 6.271,1.271 6.979,1.5 0.708,0.229 10 false OFF: Vent 6.271,0.948 7.031,1.167 0.76,0.219 10 false ON: Closed 3.833,1.5 4.188,1.708 0.354,0.208 10 false ON 3.865,1 4.219,1.208 0.354,0.208 10 false ON 5.073,0.469 5.427,0.677 0.354,0.208 10 false ON 0.406,0.542 1.188,0.75 0.781,0.208 10 false Purge VSV 0.406,1.073 1.208,1.281 0.802,0.208 10 false Vent Valve 0.156,1.427 1.156,1.781 1,0.354 10 false Leak Detection Pump 0.115,1.906 1.229,2.115 1.115,0.208 10 false EVAP Pressure 0.281,2.219 0.99,2.427 0.708,0.208 10 false Positive 0.281,2.51 1.031,2.719 0.75,0.208 10 false Negative 0.083,2.948 1.104,3.313 1.021,0.365 10 false First Reference Pressure 0.458,3.813 0.813,3.979 0.354,0.167 10 false Step 0.146,4.104 1.167,4.313 1.021,0.208 10 false Time (Seconds) 0.271,4.323 1.083,4.531 0.813,0.208 10 false (Reference) 3.688,2.24 4.625,2.448 0.938,0.208 10 false Gross Leak 3.688,2.99 4.625,3.198 0.938,0.208 10 false Small Leak 4.094,3.552 4.823,3.76 0.729,0.208 10 false No Leak 6.198,2.5 7.156,3.031 0.958,0.531 10 false [Second Reference Pressure] x 0.2 5.656,3.823 5.927,4.031 0.271,0.208 10 false 5/6 6.354,3.844 7.052,4.375 0.698,0.531 10 true [Second Reference Pressure] 5.677,4.292 5.896,4.5 0.219,0.208 10 false 60

a.

Check the EVAP pressure in step 5/6.


b.

Compare the EVAP pressure in step 3/6 and the second reference pressure (step 5/6).

Result
DTCs* Test Result Suspected Trouble Area Proceed to
- EVAP pressure (step 3/6) lower than second reference pressure (step 5/6) Not yet determined (no leakage from EVAP system) A
P0441 and P0455 EVAP pressure (step 3/6) higher than [second reference pressure (step 5/6) x 0.2]
·

Purge VSV stuck open

·

EVAP gross leak


B
P0456 EVAP pressure (step 3/6) higher than second reference pressure (step 5/6) EVAP small leak B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.



A

43.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS

B

17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV)
11.PERFORM EVAP SYSTEM CHECK (STEP 3/6)
U113559E03
0.979,3.156 1.115,3.417 false 3.781,1.875 3.417,2.438 false 3.625,2.781 3.323,3.042 false 5.073,0.469 5.469,0.677 0.396,0.208 10 false ON 3.844,1 4.24,1.208 0.396,0.208 10 false ON 3.844,1.51 4.24,1.719 0.396,0.208 10 false ON 3.833,1.781 5.219,2.156 1.385,0.375 10 true Leak Detection Pump Stuck OFF 3.677,2.646 4.813,3.042 1.135,0.396 10 false Reference Orifice High-flow 3.5,4.333 4.813,4.531 1.313,0.198 10 false Within 15 minutes 3.875,3.99 4.198,4.208 0.323,0.219 10 false 3/6 2.479,3.99 2.792,4.198 0.313,0.208 10 false 2/6 0.354,0.583 1.115,0.792 0.76,0.208 10 false Purge VSV 0.354,0.969 1.146,1.177 0.792,0.208 10 false Vent Valve 0.156,1.344 1.125,1.719 0.969,0.375 10 false Leak Detection Pump 0.063,1.844 1.198,2.052 1.135,0.208 10 false EVAP Pressure 0.208,2.135 0.906,2.344 0.698,0.208 10 false Positive 0.198,2.521 0.948,2.729 0.75,0.208 10 false Negative 0.063,2.938 1.073,3.333 1.01,0.396 10 false First Reference Pressure 0.375,3.958 0.74,4.167 0.365,0.208 10 false Step 0.75,4.156 1.177,4.365 0.427,0.208 10 false Time 0.333,4.427 1.188,4.646 0.854,0.219 10 false (Reference) 6.25,0.344 6.948,0.552 0.698,0.208 10 false ON: Open 6.25,0.906 7.021,1.115 0.771,0.208 10 false ON: Closed 6.24,0.708 7.104,0.917 0.865,0.208 10 false OFF: Closed 6.25,1.26 7,1.469 0.75,0.208 10 false OFF: Vent

a.

Check the EVAP pressure in step 3/6.

Result
DTCs* Test Result Suspected Trouble Area Proceed to
P043F EVAP pressure less than [reference pressure] measured at 2/6 Reference orifice high-flow A
P2401 EVAP pressure almost same as [reference pressure] measured at 2/6 Leak detection pump stuck OFF B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "CONFIRM DTC" procedures above.

HINT:

The first reference pressure is the value determined in step 2/6.




A

38.REPLACE CANISTER PUMP MODULE

B

31.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE)
12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR CIRCUIT)
a.

Check the canister pressure sensor circuit, referring to DTC P0451 canister pressure sensor circuit inspection procedure (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0451).



NEXT

48.REPLACE CANISTER ASSEMBLY
13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
A287416E10
2.083,0.229 1.656,0.563 false 2.073,0.698 1.74,0.583 false 2.135,0.125 2.844,0.333 0.708,0.208 10 false VLVB (+) 2.135,0.635 2.833,0.844 0.698,0.208 10 false VGND (-) 0.125,0.063 1.104,0.438 0.979,0.375 10 false Canister Pump Module:

a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Apply the battery voltage to 5 (VLVB) and 1 (VGND) terminals of the canister pump module.


d.

Touch the canister pump module to confirm the vent valve operation.

Result
Test Result Suspected Trouble Area Proceed to
Operating 1. Wire harness between vent valve and ECM
2. ECM
A
Not operating Vent valve B



A

14.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)

B

38.REPLACE CANISTER PUMP MODULE
14.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
a.

Disconnect the A27 ECM connector.


b.

Disconnect the O24 canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A27-30 (VPMP) - O24-1 (VGND) Always Below 1 Ω ECM A
Always 10 kΩ or higher Wire harness between ECM and canister pump module B



A

15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
O24-4 (MGND) - Body ground Always Below 1 Ω Leak detection pump A
Always 10 kΩ or higher Wire harness between canister pump module and body ground B



A

16.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE)
a.

Turn the ignition switch off.


b.

Disconnect the O27 canister pump module connector.


c.

Disconnect the A24 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A27-49 (MPMP) - O24-3 (MTRB) Always Below 1 Ω ECM A
Always 10 kΩ or higher Wire harness between ECM and canister pump module B



A

45.REPLACE CANISTER PUMP MODULE

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV)
A163184E02
1.052,1.531 1.844,1.719 true 2.156,3 2.604,2.688 true 0.167,1.448 1.021,1.76 0.854,0.313 10 true Purge VSV 0.938,2.927 2.146,3.302 1.208,0.375 10 true Hose (to Canister)

a.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


b.

Disconnect the hose (connected to the canister) from the purge VSV.


c.

Start the engine.


d.

Using the Techstream, turn off the purge VSV (Activate the VSV for Evap Control: OFF).


e.

Use your finger to confirm that the purge VSV has no suction.


f.

Using the Techstream, turn on the purge VSV (Activate the VSV for Evap Control: ON).


g.

Use your finger to confirm that the purge VSV has suction.

Result
Test Result Suspected Trouble Area Proceed to
No suction when purge VSV turned OFF, and suction applied when turned ON Blockage in the purge line is considered (based on result of step 9):
·

Problems with EVAP hose between canister and purge VSV

·

Canister (charcoal filter inside canister) clogged

·

ECM


A
Leakage is considered (based on result of step 10):
·

Fuel cap

·

Leakage from EVAP line, fuel tank, or canister assembly


B
Suction applied when purge VSV turned OFF Purge VSV stuck open C
No suction when purge VSV turned ON
·

Purge VSV stuck closed

·

Problems with purge line between purge VSV and intake manifold


D



A

18.INSPECT EVAP HOSE (PURGE VSV - CANISTER)

B

20.CHECK FUEL CAP ASSEMBLY

C

21.INSPECT PURGE VSV

D

23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)
18.INSPECT EVAP HOSE (PURGE VSV - CANISTER)
a.

Check for blockages in the EVAP purge line between the purge VSV and canister.

OK:

No blockages in the EVAP purge line between the purge VSV and canister.




OK

19.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER)

NG

44.REPAIR OR REPLACE EVAP HOSE
19.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER)
a.

Check for filter blockage in the canister (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>CANISTER>INSPECTION).

OK:

No blockages in the canister.




OK

47.REPLACE ECM

NG

48.REPLACE CANISTER ASSEMBLY
20.CHECK FUEL CAP ASSEMBLY
a.

Check that the fuel cap is correctly installed and confirm that the fuel cap meets OEM specifications.


b.

Tighten the fuel cap firmly (only one click sound could be heard).

HINT:

If an EVAP tester is available, check the fuel cap using the Techstream.


i.

Remove the fuel cap and install it onto a fuel cap adapter.


ii.

Connect an EVAP tester pump hose to the adapter, and pressurize the cap to 3.2 to 3.7 kPa (gauge) [24 to 28 mmHg (gauge)] using an EVAP tester pump.


iii.

Seal the adapter and wait for 2 minutes.


iv.

Check the pressure. If the pressure is 2 kPa (gauge) [15 mmHg (gauge)] or more, the fuel cap is normal.

Result
Test Result Suspected Trouble Area Proceed to
Fuel cap correctly installed - A
Fuel cap loose
·

Fuel cap improperly installed

·

Defective fuel cap

·

Fuel cap does not meet OEM specifications


B
Defective fuel cap - B
No fuel cap - C




A

37.LOCATE EVAP LEAK PART

B

35.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY

C

36.REPLACE FUEL TANK CAP
21.INSPECT PURGE VSV
A163185E02
1.083,1.552 1.875,1.74 true 2.385,2.99 2.635,2.708 true 0.26,1.458 1.042,1.781 0.781,0.323 10 true Purge VSV 1.135,2.938 2.344,3.313 1.208,0.375 10 true Hose (to Canister)

a.

Turn the ignition switch off.


b.

Disconnect the D29 purge VSV connector.


c.

Disconnect the hose (connected to the canister) from the purge VSV.


d.

Start the engine.


e.

Use your finger to confirm that the purge VSV has no suction.

Result
Test Result Suspected Trouble Area Proceed to
No suction
·

Wire harness or connector between purge VSV and ECM (short to ground)

·

ECM


A
Suction applied Purge VSV B



A

26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

B

39.REPLACE PURGE VSV
22.INSPECT EVAP HOSE (PURGE VSV - CANISTER)
a.

Check for blockages in the EVAP purge line between the purge VSV and canister.

OK:

No blockages in the EVAP purge line between the purge VSV and canister.




OK

23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)

NG

44.REPAIR OR REPLACE EVAP HOSE
23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD)
A163186E02
0.927,1.49 1.771,1.708 true 1.313,2.76 0.844,2.406 true 0.104,1.438 0.917,1.771 0.813,0.333 10 true Purge VSV 1.344,2.708 2.969,3.104 1.625,0.396 10 true Hose (to Intake Manifold)

a.

Disconnect the hose (connected to the intake manifold) from the purge VSV.


b.

Start the engine.


c.

Use your finger to confirm that the hose has suction.


Result
Test Result Suspected Trouble Area Proceed to
Suction applied EVAP hose between purge VSV and intake manifold normal
·

Purge VSV

·

Purge VSV power source

·

ECM


A
No suction
·

Intake manifold port

·

EVAP hose between purge VSV and intake manifold


B


A

24.INSPECT PURGE VSV

B

34.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
24.INSPECT PURGE VSV
A371145E02
2.302,0.938 1.948,0.344 false 1.167,0.24 1.979,0.438 0.813,0.198 10 false Purge VSV 1.281,0.865 1.802,1.042 0.521,0.177 10 false Port B 1.458,1.521 1.979,1.698 0.521,0.177 10 false Port A


b.

Apply the battery voltage to the terminals of the purge VSV.


c.

Using an air gun, confirm that air flows from port A to port B.


Result
Test Result Suspected Trouble Area Proceed to
Air flows Purge VSV normal
·

Purge VSV power source

·

Wire harness or connector between purge VSV and ECM


A
No air flow Purge VSV B


A

25.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV)

B

39.REPLACE PURGE VSV
25.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV)
U152993E02
0.104,0.115 2.458,0.479 2.354,0.365 10 false Front view of wire harness connector: (to Purge VSV) 0.427,1.865 0.771,2.031 0.344,0.167 10 false D16

a.

Disconnect the D16 purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Result
Tester Connection Switch Condition Specified Condition Suspected Trouble Area Proceed to
D16-1 - Body ground Ignition switch ON 11 to 14 V Purge VSV power source normal
·

Wire harness or connector between purge VSV and ECM


A
Ignition switch ON Other than condition above Wire harness or connectors between purge VSV and battery B



A

26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the D56 ECM connector and the D16 purge VSV connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D56-63 (PRG) - D16-2 Always Below 1 Ω
D56-63 (PRG) or D16-2 - Body ground Always 10 kΩ or higher




OK

47.REPLACE ECM

NG

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
27.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)
U153147E01
0.111,2.51 2.763,2.705 2.652,0.195 10 Front view of wire harness connector: 0.111,2.733 1.856,2.928 1.745,0.195 10 (to Canister Pump Module) 0.523,4.271 0.925,4.427 0.401,0.156 10 VLVB 0.967,4.338 1.354,4.048 false 2.57,3.757 2.870,3.927 0.299,0.170 10 O24

a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Result
Tester Connection Switch Condition Specified Condition Suspected Trouble Area Proceed to
O24-5 (VLVB) - Body ground Ignition switch ON 11 to 14 V
·

Wire harness or connector between vent valve and ECM

·

Vent valve

·

Canister (charcoal filter inside canister) clogged

·

ECM


A
Ignition switch ON Below 3 V Power source wire harness of vent valve B



A

28.INSPECT PUMP MODULE (VENT VALVE OPERATION)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
28.INSPECT PUMP MODULE (VENT VALVE OPERATION)
A287416E10
2.083,0.229 1.656,0.563 false 2.073,0.698 1.74,0.583 false 2.135,0.125 2.844,0.333 0.708,0.208 10 false VLVB (+) 2.135,0.635 2.833,0.844 0.698,0.208 10 false VGND (-) 0.125,0.063 1.104,0.438 0.979,0.375 10 false Canister Pump Module:

a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Apply the battery voltage to 5 (VLVB) and 1 (VGND) terminals of the canister pump module.


d.

Touch the canister pump module to confirm the vent valve operation.

Result
Test Result Suspected Trouble Area Proceed to
Operating
·

Wire harness or connector between vent valve and ECM

·

Canister (charcoal filter inside canister) clogged

·

ECM


A
Not operating Vent valve B



A

29.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

38.REPLACE CANISTER PUMP MODULE
29.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the A27 ECM connector.


b.

Disconnect the O24 canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A27-30 (VPMP) - O24-1 (VGND) Always Below 1 Ω ECM A
Always 10 kΩ or higher Wire harness between ECM and canister pump module B



A

30.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER)

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
30.INSPECT CANISTER (CHARCOAL FILTER INSIDE CANISTER)
a.

Check for filter blockage in the canister (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>CANISTER>INSPECTION).

OK:

No blockages in the canister.




OK

47.REPLACE ECM

NG

48.REPLACE CANISTER ASSEMBLY
31.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE)
U153148E01
0.111,2.51 2.763,2.705 2.652,0.195 10 Front view of wire harness connector: 0.111,2.733 1.856,2.928 1.745,0.195 10 (to Canister Pump Module) 2.471,4.2 3.086,4.355 0.614,0.156 10 MTRB 2.445,4.272 1.781,3.882 false 0.425,3.88 0.724,4.050 0.299,0.170 10 O24

a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
O24-3 (MTRB) - Body ground Leak detection pump is turned ON and OFF using the Techstream
Leak detection pump is turned ON and OFF using the Techstream
Leak detection pump is turned ON and OFF using the Techstream
Below 3 V when OFF
9 to 14 V when ON
·

Wire harness between leak detection pump and body ground

·

Leak detection pump


A
Below 3 V when OFF and ON
·

Wire harness between leak detection pump and ECM

·

ECM


B
9 to 14 V when OFF and ON ECM C



A

32.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)

B

33.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

47.REPLACE ECM
32.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
O24-4 (MGND) - Body ground Always Below 1 Ω Leak detection pump A
Always 10 kΩ or higher Wire harness between canister pump module and body ground B



A

38.REPLACE CANISTER PUMP MODULE

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
33.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the O24 canister pump module connector.


c.

Disconnect the A27 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A27-49 (MPMP) - O24-3 (MTRB) Always Below 1 Ω ECM A
Always 10 kΩ or higher Wire harness between ECM and canister pump module B



A

47.REPLACE ECM

B

40.REPAIR OR REPLACE HARNESS OR CONNECTOR
34.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
a.

Stop the engine.


b.

Disconnect the purge line from the intake manifold.


c.

Start the engine.


d.

Use your finger to confirm that the port of the intake manifold has suction.


Result
Test Result Suspected Trouble Area Proceed to
Suction applied Purge line between intake manifold and purge VSV A
No suction Intake manifold B

e.

Reconnect the purge line.



A

41.REPLACE PURGE LINE (INTAKE MANIFOLD - PURGE VSV)

B

42.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
35.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY
HINT:
·

When reinstalling the fuel cap, tighten it firmly (only one click sound could be heard).

·

When replacing the fuel cap, use a fuel cap that meets OEM specifications, and install it firmly.




NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
36.REPLACE FUEL TANK CAP
HINT:

When replacing the fuel cap, use a fuel cap that meets OEM specifications, and tighten it until a few click sounds are heard.



NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
37.LOCATE EVAP LEAK PART
A312840E01
0.483,3.667 1.368,3.851 0.885,0.184 10 EVAP Tester 2.059,3.674 2.666,3.858 0.607,0.184 10 Adapter 5.399,3.188 6.374,3.546 0.975,0.357 10 Canister Outlet Hose 5.192,3.114 5.287,3.265 false 5.287,3.265 5.381,3.265 false

a.

Disconnect the vent hose.


b.

Connect an EVAP tester to the canister pump module with the adapter.


c.

Pressurize the EVAP system to 3.2 to 3.7 kPa (24 to 28 mmHg).


d.

Apply soapy water to the piping and connecting parts of the EVAP system.


e.

Look for areas where bubbles appear. This indicates the leak point.


f.

Repair or replace the leak point.

HINT:

Disconnect the hose between the canister and the fuel tank from the canister. Block the canister side and conduct an inspection. In this way, the fuel tank can be excluded as an area suspected of causing fuel leaks.




NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
38.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in canister interior, replace canister and canister pump module together (replace canister assembly).

·

Check for filter blockage in the canister assembly. If the charcoal filter inside the canister assembly is clogged, replace canister and canister pump module together (replace canister assembly).

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.



U153145E02
3.656,5.125 5.292,5.125 false 3.156,2.552 5.292,2.552 false 5.01,2.625 5.01,5.063 false 1.938,6.229 1.938,6.479 false 3.802,5.479 3.802,6.469 false 3.729,6.365 2,6.365 false 1.5,5.302 1.948,6.167 true 2.573,4 3.563,4.354 false 3.604,5.646 4.302,6.219 4.302,6.219 3.313,5.844 true 5.083,3.771 6.302,4.01 1.219,0.24 10 false Inspection Area* 2.292,6.396 3.365,6.677 1.073,0.281 10 false Inspection Area* 4.344,6.156 5.031,6.479 0.688,0.323 10 false Vent Hose 0.698,5.115 1.5,5.385 0.802,0.271 10 false Air Inlet Port 1.198,3.906 2.583,4.25 1.385,0.344 10 false Fuel Tank Vent Hose 4.406,0.063 7.031,0.385 2.625,0.323 10 false *: Check for disconnection and/or cracks



NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
39.REPLACE PURGE VSV

NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
40.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
41.REPLACE PURGE LINE (INTAKE MANIFOLD - PURGE VSV)

NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
42.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT)
a.

Check that the EVAP purge port of the intake manifold is not clogged. If necessary, replace the intake manifold.



NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
43.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS
a.

Repair the malfunctioning areas indicated by the DTCs that had been confirmed when the vehicle was brought in.



NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
44.REPAIR OR REPLACE EVAP HOSE

NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
45.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in canister interior, replace canister and canister pump module together (replace canister assembly).

·

Check for filter blockage in the canister assembly. If the charcoal filter inside the canister assembly is clogged, replace canister and canister pump module together (replace canister assembly).

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.



U153145E02
3.656,5.125 5.292,5.125 false 3.156,2.552 5.292,2.552 false 5.01,2.625 5.01,5.063 false 1.938,6.229 1.938,6.479 false 3.802,5.479 3.802,6.469 false 3.729,6.365 2,6.365 false 1.5,5.302 1.948,6.167 true 2.573,4 3.563,4.354 false 3.604,5.646 4.302,6.219 4.302,6.219 3.313,5.844 true 5.083,3.771 6.302,4.01 1.219,0.24 10 false Inspection Area* 2.292,6.396 3.365,6.677 1.073,0.281 10 false Inspection Area* 4.344,6.156 5.031,6.479 0.688,0.323 10 false Vent Hose 0.698,5.115 1.5,5.385 0.802,0.271 10 false Air Inlet Port 1.198,3.906 2.583,4.25 1.385,0.344 10 false Fuel Tank Vent Hose 4.406,0.063 7.031,0.385 2.625,0.323 10 false *: Check for disconnection and/or cracks



NEXT

46.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
46.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 18 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the temperature below 35°C (95°F).



a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.


f.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes

Result Proceed to
EVAP system DTCs are output A
No DTCs output B



A

47.REPLACE ECM

B

END

47.REPLACE ECM

NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
48.REPLACE CANISTER ASSEMBLY
a.

Replace the canister assembly (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in canister interior, replace canister and canister pump module together (replace canister assembly).

·

Check for filter blockage in the canister assembly. If the charcoal filter inside the canister assembly is clogged, replace canister and canister pump module together (replace canister assembly).

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.



U153145E02
3.656,5.125 5.292,5.125 false 3.156,2.552 5.292,2.552 false 5.01,2.625 5.01,5.063 false 1.938,6.229 1.938,6.479 false 3.802,5.479 3.802,6.469 false 3.729,6.365 2,6.365 false 1.5,5.302 1.948,6.167 true 2.573,4 3.563,4.354 false 3.604,5.646 4.302,6.219 4.302,6.219 3.313,5.844 true 5.083,3.771 6.302,4.01 1.219,0.24 10 false Inspection Area* 2.292,6.396 3.365,6.677 1.073,0.281 10 false Inspection Area* 4.344,6.156 5.031,6.479 0.688,0.323 10 false Vent Hose 0.698,5.115 1.5,5.385 0.802,0.271 10 false Air Inlet Port 1.198,3.906 2.583,4.25 1.385,0.344 10 false Fuel Tank Vent Hose 4.406,0.063 7.031,0.385 2.625,0.323 10 false *: Check for disconnection and/or cracks



NEXT

49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
49.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 18 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed. If the cut-off valve is closed, the fuel tank leak check is not possible.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the temperature below 35°C (95°F).



a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.


f.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes

HINT:

If no pending DTCs are found, the repair has been successfully completed.




NEXT

END