The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1 and EV2 signals) consists of a magnet and MRE (Magnetic Resistance Element).
The exhaust camshaft has 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0365
P0390 |
No VVT sensor signal to ECM at engine speed of 600 rpm or more
(1 trip detection logic) |
·
Open or short in VVT sensor for exhaust camshaft circuit ·
VVT sensor for exhaust camshaft ·
Exhaust camshaft ·
Jumped tooth of timing chain ·
ECM |
| P0367
P0392 |
Output voltage of VVT sensor less than 0.3 V 4 seconds
(1 trip detection logic) |
·
Open or short in VVT sensor for exhaust camshaft circuit ·
VVT sensor for exhaust camshaft ·
Exhaust camshaft ·
Jumped tooth of timing chain ·
ECM |
| P0368
P0393 |
Output voltage of VVT sensor more than 4.7 V 4 seconds
(1 trip detection logic) |
·
Open or short in VVT sensor for exhaust camshaft circuit ·
VVT sensor for exhaust camshaft ·
Exhaust camshaft ·
Jumped tooth of timing chain ·
ECM |
Reference: Inspection using an oscilloscope
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| D56-69 (EV1+) - D56-68 (EV1-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| D56-64 (EV2+) - D56-65 (EV2-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
EV1+ and EV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
If no signal is transmitted by the VVT sensor despite the exhaust camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
| Related DTCs | P0365: VVT sensor (for Bank 1) verify pulse input
P0365: VVT sensor (for Bank 1) chattering P0367: VVT position sensor (for Bank 1) range check (low voltage) P0368: VVT position sensor (for Bank 1) range check (high voltage) P0390: VVT sensor (for Bank 2) verify pulse input P0390: VVT sensor (for Bank 2) chattering P0392: VVT position sensor (for Bank 2) range check (low voltage) P0393: VVT position sensor (for Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT position sensor (for Bank 1 and 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds: P0365, P0390
4 seconds: Others |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | None |
| Engine speed | 600 rpm or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Ignition switch | ON |
| Exhaust VVT sensor voltage | 0.3 to 4.7 V |
| Exhaust VVT sensor range check low voltage fail (P0367, P0392) | Not detected |
| Exhaust VVT sensor range check high voltage fail (P0368, P0393) | Not detected |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 2 seconds or more |
| Exhaust VVT sensor verify pulse input fail (P0365, P0390) | Not detected |
| Battery voltage | 8 V or more |
| Exhaust VVT sensor signal | No signal |
| Exhaust VVT sensor voltage | Less than 0.3 V |
| Exhaust VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine.
Idle the engine for 10 seconds [B].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0365, P0367, P0368, P0390, P0392 or P0393.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Disconnect the D24 or D25 VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (VC2) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
OK
NG
Disconnect the D24 or D25 VVT sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D24-1 (EX+) - D56-69 (EV1+) | Always | Below 1 Ω |
| D24-2 (EX-) - D56-68 (EV1-) | Always | Below 1 Ω |
| D25-1 (EX+) - D56-64 (EV2+) | Always | Below 1 Ω |
| D25-2 (EX-) - D56-65 (EV2-) | Always | Below 1 Ω |
| D24-1 (EX+) or D56-69 (EV1+) - Body ground | Always | 10 kΩ or higher |
| D24-2 (EX-) or D56-68 (EV1-) - Body ground | Always | 10 kΩ or higher |
| D25-1 (EX+) or D56-64 (EV2+) - Body ground | Always | 10 kΩ or higher |
| D25-2 (EX-) or D56-65 (EV2-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the VVT sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the camshaft.
Teeth do not have any cracks or deformation.
Perform "Inspection After Repair" after replacing the exhaust camshaft (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Replace the VVT sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| No output | A |
| P0365, P0367, P0368, P0390, P0392 or P0393 | B |
If the engine does not start, replace the ECM.
A
B