Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P014C  A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1  P014D  A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1  P014E  A/F Sensor Slow Response - Rich to Lean Bank 2 Sensor 1  P014F  A/F Sensor Slow Response - Lean to Rich Bank 2 Sensor 1  P015A  A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1  P015B  A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1  P015C  A/F Sensor Delayed Response - Rich to Lean Bank 2 Sensor 1  P015D  A/F Sensor Delayed Response - Lean to Rich Bank 2 Sensor 1  


DESCRIPTION

HINT:

Refer to DTC P2195 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P2195).


DTC No. DTC Detection Condition Trouble Area
P014C The "Rich to Lean response rate deterioration level*" value is less than the standard.
(2 trip detection logic)
·

Air fuel ratio sensor (for bank 1 sensor 1)

·

Air fuel ratio sensor (for bank 1 sensor 1) heater

·

ECM


P014D The "Lean to Rich response rate deterioration level*" value is more than the standard.
(2 trip detection logic)
P014E The "Rich to Lean response rate deterioration level*" value is less than the standard.
(2 trip detection logic)
·

Air fuel ratio sensor (for bank 2 sensor 1)

·

Air fuel ratio sensor (for bank 2 sensor 1) heater

·

ECM


P014F The "Lean to Rich response rate deterioration level*" value is more than the standard.
(2 trip detection logic)
P015A The "Rich to Lean delay level*" value is less than the standard.
(2 trip detection logic)
·

Air fuel ratio sensor (for bank 1 sensor 1)

·

Air fuel ratio sensor (for bank 1 sensor 1) heater

·

ECM


P015B The "Lean to Rich delay level*" value is more than the standard.
(2 trip detection logic)
P015C The "Rich to Lean delay level*" value is less than the standard.
(2 trip detection logic)
·

Air fuel ratio sensor (for bank 2 sensor 1)

·

Air fuel ratio sensor (for bank 2 sensor 1) heater

·

ECM


P015D The "Lean to Rich delay level*" value is more than the standard.
(2 trip detection logic)

*: Calculated by the ECM based on the air fuel ratio sensor output

MONITOR DESCRIPTION

After the engine is warm, the ECM carries out air-fuel ratio feedback control, and maintains the air-fuel ratio at the stoichiometric level. In addition, after all the preconditions have been met, active air-fuel ratio control is carried out for approx. 10 seconds, and during active air-fuel ratio control, the ECM measures the response of the air fuel ratio sensor by increasing or decreasing the injection volume by a specific quantity based on the stoichiometric air-fuel ratio learned during normal air-fuel control. The ECM determines whether there is an air fuel ratio sensor malfunction at the mid-point of active air-fuel ratio control.

If the air fuel ratio sensor's response ability is reduced, DTC P014C, P014D, P014E and P014F are stored.

If the time it takes the air fuel ratio sensor output to change is delayed, DTC P015A, P015B, P015C and P015D are stored.

A223538E07
0.133,0.032 2.413,0.216 2.281,0.184 12 Air Fuel Ratio Sensor Output: 0.289,0.978 1.500,1.161 1.211,0.184 10 Active A/F Control 0.289,1.938 2.128,2.278 1.839,0.339 10 Air Fuel Ratio Sensor Output (Response Rate) 3.558,1.317 4.061,1.501 0.503,0.184 10 Normal 5.464,1.278 6.226,1.462 0.761,0.184 10 Malfunction 4.438,0.456 5.247,0.640 0.809,0.184 10 10 seconds 0.289,4.245 1.699,4.429 1.411,0.184 10 Fuel Injection Volume 2.774,3.966 3.416,4.150 0.642,0.184 10 Increase 2.774,4.438 3.416,4.621 0.642,0.184 10 Decrease 1.835,0.766 2.232,0.913 0.397,0.147 10 On 1.835,1.075 2.206,1.258 0.371,0.184 10 Off 4.206,1.689 4.049,1.387 false 5.228,1.921 5.445,1.357 false 0.289,3.13 2.142,3.484 1.853,0.354 10 Air Fuel Ratio Sensor Output (Delay Time) 3.58,2.684 4.083,2.868 0.503,0.184 10 Normal 4.795,2.54 5.556,2.724 0.761,0.184 10 Malfunction 4.189,2.993 4.07,2.754 false 4.511,2.979 4.762,2.606 false

MONITOR STRATEGY

Related DTCs P014C: Air fuel ratio sensor (bank 1) slow response (rich to lean)
P014D: Air fuel ratio sensor (bank 1) slow response (lean to rich)
P014E: Air fuel ratio sensor (bank 2) slow response (rich to lean)
P014F: Air fuel ratio sensor (bank 2) slow response (lean to rich)
P015A: Air fuel ratio sensor (bank 1) delayed response (rich to lean)
P015B: Air fuel ratio sensor (bank 1) delayed response (lean to rich)
P015C: Air fuel ratio sensor (bank 2) delayed response (rich to lean)
P015D: Air fuel ratio sensor (bank 2) delayed response (lean to rich)
Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Vehicle speed sensor, crankshaft position sensor
Frequency of Operation Once per driving cycle
Duration 10 to 15 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not stored P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P0451, P0452, P0453 (EVAP system)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC valve)
P1340 (Camshaft position sensor)
P2440 - P2447 (Secondary air injection system)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
Active air fuel ratio control Performing
Active air fuel ratio control is performed when the following conditions met -
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idle OFF
Engine speed 1000 to 2500 rpm
Air fuel ratio sensor status Activated
Fuel-cut OFF
Engine load 10 to 70%
Shift position 2nd or higher
Catalyst monitor Not executed
Mass air flow 4 to 11.4 gm/sec

TYPICAL MALFUNCTION THRESHOLDS

Air Fuel Ratio Sensor Slow Response (Rich to Lean)
Rich to Lean response rate deterioration level 0.03 V or less

Air Fuel Ratio Sensor Slow Response (Lean to Rich)
Lean to Rich response rate deterioration level -0.035 V or higher

Air Fuel Ratio Sensor Delayed Response (Rich to Lean)
Rich to Lean delay level 350 ms or more

Air Fuel Ratio Sensor Delayed Response (Lean to Rich)
Lean to Rich delay level 350 ms or more

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A201252E02
0.676,0.41 1.594,0.578 0.918,0.168 10 Vehicle Speed 0.181,0.81 1.567,1.402 1.387,0.592 10 Between 75 km/h and 100 km/h (47 mph and 62 mph) 1.223,2.265 1.599,2.425 0.376,0.161 10 Idling 0.353,2.544 1.591,2.697 1.238,0.153 10 Ignition Switch off 2.35,2.148 2.547,2.338 0.197,0.189 10 [A] 3.908,0.765 4.115,0.940 0.207,0.175 10 [B] 2.068,2.879 2.907,3.047 0.838,0.168 10 Warming up 3.574,2.903 4.357,3.050 0.783,0.146 10 10 minutes 5.712,2.75 6.051,2.896 0.339,0.145 10 Time 4.655,3.052 4.852,3.241 0.197,0.189 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor.

8.

Check that the monitor item O2 Sensor is Incomplete.

HINT:

The test values for the test items RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1 do not exist in the Detail of O2 Sensor monitor at this time (the initial value of "0.000" is indicated for each test item).


9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

10.

Drive the vehicle at a constant speed of between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].

11.

Check that the monitor item O2 Sensor becomes Complete.

HINT:

Check the test values on the Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor /Details / RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1.


12.

If the monitor item O2 Sensor does not become Complete (if the test values indicated on the Techstream do not change), perform Readiness Monitor Drive Pattern for the air fuel ratio sensor and heated oxygen sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>READINESS MONITOR DRIVE PATTERN).

13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

16.

Input the DTC: P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D.

17.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


18.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output A
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D and other DTCs are output B

HINT:

If any DTCs other than P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

4.CHECK AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR FUEL RATIO SENSOR
a.

Check that the proper air fuel ratio sensor is installed to the vehicle.

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to Confirmation Driving Pattern.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the DTCs.

Result
Result Proceed to
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output A
DTC is not output B



A

7.REPLACE AIR FUEL RATIO SENSOR

B

7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to Confirmation Driving Pattern.



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output B



A

END

B

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO