Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL INJECTOR
RM27L0U _51 Engine / Hybrid System _049298 3UR-FE FUEL _0235578 FUEL INJECTOR A

3UR-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.
U153105E01
2.467,1.811 2.645,1.987 0.178,0.176 10 *1 1.595,1.114 2.435,1.87 false

Turn the lock lever and disconnect the connector of the fuel pump ECU.

Text in Illustration
*1 Lock Lever


c.

Connect the cable to the negative (-) battery terminal.


d.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

DTC P0171/0174 (system too lean) may be set.



e.

Crank the engine again, and then check that the engine does not start.


f.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


g.
U153106E01
0.624,2.978 0.802,3.154 0.178,0.176 10 *1 0.93,2.947 0.8,3.068 false 3.084,2.965 3.262,3.141 0.178,0.176 10 *1 3.069,3.042 2.917,2.945 false

Connect the connector of the fuel pump ECU.


h.

Turn the lock lever and secure the connector with the lock lever.

Text in Illustration
*1 Lock Lever


Hide 23902 5.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A161418

Disconnect the No. 2 fuel tube from the fuel pressure regulator (for quick type A) (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A256329

Disconnect the fuel tube from the fuel delivery pipe (for quick type A) (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.
A161415

Disconnect the fuel tube from the No. 2 fuel delivery pipe (for quick type A) (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23801P 7.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A308885

Detach the clamp.


b.

Disconnect the No. 1 fuel pipe from the No. 2 fuel delivery pipe (for quick type B) (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 12263 8.DISCONNECT NO. 3 VENTILATION HOSE

a.
A161422

Disconnect the No. 3 ventilation hose and No. 6 wire harness connector.


Hide 12613 9.REMOVE NO. 3 ENGINE COVER

a.

Remove the No. 3 engine cover.


Hide 23807 10.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A256330

Remove the 2 bolts and fuel delivery pipe.

NOTICE:

When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.



b.

Remove the 2 spacers and 4 insulators from the intake manifold.


Hide 12601B 11.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Remove the No. 1 engine cover.


Hide 23808 12.REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Disconnect the No. 7 wire harness connector.


b.
A256331

Remove the 2 bolts and No. 2 fuel delivery pipe.

NOTICE:

When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.



c.

Remove the 2 spacers and 4 insulators from the intake manifold.


Hide 23250 13.REMOVE FUEL INJECTOR ASSEMBLY

a.
A161427

Remove the fuel injector from the fuel delivery pipe, and then disconnect the injector connector.

NOTICE:
A380111

For reinstallation, attach a tag or label to the injector shaft.



b.
A149190E07
2.773,1.735 2.964,1.909 0.191,0.173 10 *1 2.852,1.454 2.852,1.704 false

Remove the O-ring from the fuel injector.

Text in Illustration
*1 O-Ring