Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM27L0U _51 Engine / Hybrid System _049301 3UR-FE INTAKE / EXHAUST _0235604 EXHAUST MANIFOLD A

3UR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


PROCEDURE

Hide 53736 2.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 6 clips and fender apron seal.


Hide 53736A 3.REMOVE FRONT FENDER APRON SEAL REAR RH

a.

Remove the 5 clips and fender apron seal.


Hide 53737B 4.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 6 clips and fender apron seal.


Hide 53739A 5.REMOVE FRONT FENDER APRON SEAL REAR LH

a.

Remove the 5 clips and fender apron seal.


Hide 11452 6.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 37117B 7.REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)

Hide 37140 8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 17450B 9.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

A184981

a.

Remove the 2 bolts from the center exhaust pipe.


b.

Remove the 2 bolts and 2 nuts from the front No. 2 exhaust pipe sub-assembly.


c.

Disconnect the front No. 3 exhaust pipe sub-assembly and from exhaust pipe support.


d.

Remove the 2 gaskets.


e.

Disconnect the air fuel ratio sensor connector.


f.

Disconnect the heated oxygen sensor connector.


g.
A184304

Remove the 3 nuts, No. 2 exhaust pipe sub-assembly and gasket.


Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the heated oxygen sensor connector and 2 clamps.


c.
A184982

Remove the 2 bolts from the center exhaust pipe.


d.

Remove the 3 nuts, front exhaust pipe and 2 gaskets.


Hide 58156 11.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR

A184951

a.

Remove the 4 nuts and front No. 4 floor heat insulator.


Hide 58155 12.REMOVE FRONT NO. 3 FLOOR HEAT INSULATOR

A184950

a.

Remove the 4 nuts and front No. 3 floor heat insulator.


Hide 45203 13.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C155150E04
1.365,1.417 0.948,1.781 false 0.948,1.781 1.719,1.563 false 0.49,1.781 1.24,1.948 0.75,0.167 10 true Matchmark

Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and steering intermediate shaft.


b.

Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the steering intermediate shaft.


c.
C155151E05
0.99,1.469 1.646,1.344 false 0.99,1.469 1.677,1.563 false 0.219,1.385 0.969,1.552 0.75,0.167 10 true Matchmark

Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and the power steering gear.


d.

Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the power steering gear.


Hide 17168 14.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A162114

Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


Hide 17105 15.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A162115

Remove the 10 nuts, exhaust manifold sub-assembly LH and 2 gaskets.


Hide 17167 16.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A162752

Remove the 3 bolts and No. 1 exhaust manifold heat insulator.


Hide 17104 17.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A162754

Remove the 10 nuts, exhaust manifold sub-assembly RH and 2 gaskets.