Home › Engine / Hybrid System › 3UR-FBE COOLING › WATER PUMP
RM27L0U _51 Engine / Hybrid System _049303 3UR-FBE COOLING _0235613 WATER PUMP A

3UR-FBE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A151828E04
1.938,0.042 2.052,0.188 0.115,0.146 10 false A 1.396,0.031 1.542,0.177 0.146,0.146 10 true A 2.521,1.604 2.635,1.75 0.115,0.146 10 false B 2.302,0.031 2.427,0.188 0.125,0.156 10 false C 3.021,1.365 3.146,1.5 0.125,0.135 10 false C 2.323,1.969 2.448,2.125 0.125,0.156 10 true C 0.281,0.854 0.406,1.031 0.125,0.177 10 false C 0.615,1.927 0.76,2.104 0.146,0.177 10 true C

Install a new gasket and the engine water pump with the 8 bolts shown in the illustration.

Torque:
for bolt A : 47 N*m (479 kgf*cm, 35 ft.*lbf)
for bolt B : 23 N*m (235 kgf*cm, 17 ft.*lbf)
for bolt C : 20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 16173 2.INSTALL WATER PUMP PULLEY

a.
A151837E02
0.347,1.797 0.636,1.946 0.289,0.149 10 SST 1.497,1.654 0.848,1.887 0.848,1.887 0.742,1.887 false

Temporarily install the pulley with the 4 bolts.


b.

Using SST, hold the pulley and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16323 3.INSTALL INLET WATER HOUSING

a.
A162555E07
0.488,0.138 0.709,0.327 0.221,0.189 10 *1 0.729,0.228 0.789,0.228 false 0.789,0.228 1.21,0.79 false

Install a new gasket to the water pump.

Text in Illustration
*1 Gasket


b.
A183227E02
0.853,1.099 1.164,1.252 0.312,0.153 10 45° 1.127,1.191 1.348,1.333 0.221,0.142 10 *a

Connect the No. 3 water by-pass hose to the water inlet housing.

Text in Illustration
*a Front


c.

Install the water inlet housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Install the hose so that the direction of the hose clamp is as indicated in the illustration.



Hide 16281F 4.CONNECT NO. 5 WATER BY-PASS HOSE

Hide 17342 6.CONNECT NO. 2 AIR INJECTION SYSTEM HOSE

Hide 17343 7.CONNECT NO. 3 AIR INJECTION SYSTEM HOSE

Hide 16261G 9.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Install the No. 1 water by-pass hose to the water by-pass joint and water inlet housing.


Hide 16572 12.CONNECT OUTLET RADIATOR HOSE

Hide 17880 13.INSTALL AIR CLEANER HOSE ASSEMBLY

A198568E02
0.149,0.664 0.471,0.814 0.322,0.150 10 90° 0.474,0.32 0.700,0.474 0.226,0.154 10 *a 0.842,0.889 1.102,1.032 0.259,0.143 10 *b

a.

Connect the air cleaner hose and tighten clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Connect the No. 2 ventilation hose with the clamp.

HINT:

Install the hose so that the direction of the hose clamp is as indicated in the illustration.

Text in Illustration
*a Top
*b RH



c.

Connect the vacuum hose.


Hide 17700 14.INSTALL AIR CLEANER ASSEMBLY

a.
A299488E02
0.719,1.25 0.719,1.521 false 0.625,1.552 0.896,1.75 0.271,0.198 10 true *1

Attach grommet to air cleaner before mounting the air cleaner.

Text in Illustration
*1 Grommet


b.

Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.


c.

Install the air cleaner with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector and install the clamp and wire harness.


e.

Connect the air cleaner hose and tighten the clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)