When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0571 | Voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more. | ·
Stop light switch ·
Stop light switch circuit ·
ECM |
| This trouble code is output when the BRK relay error signal from the skid control ECU for 0.2 seconds. or more while the dynamic cruise control is in operation. | VSC system |
Check for DTCs in Vehicle Stability Control System (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
DTC is not output.
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Laser Cruise / Data List.
Check the Data List for proper functioning of the stop light switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stp Light SW M-CPU | Stop light switch signal (Main CPU) / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 3UR-FE) | B |
| OK (for 3UR-FBE) | C |
A
B
C
Disconnect the A4 connector from the stop light switch.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A4-2 - Body ground | Always | 11 to 14 V |
| A4-4 - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the stop light switch connector.
OK
NG
Remove the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch pin not pushed | Below 1 Ω |
| 3 - 4 | Switch pin not pushed | 10 kΩ or higher |
| 1 - 2 | Switch pin pushed | 10 kΩ or higher |
| 3 - 4 | Switch pin pushed | Below 1 Ω |
Reinstall the stop light switch.
OK
NG
Disconnect the A27 connector from the ECM.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A27-26 (STP) - Body ground | Brake pedal is depressed | 11 to 14 V |
| A27-26 (STP) - Body ground | Brake pedal is released | Below 1 V |
| A27-35 (ST1-) - Body ground | Brake pedal is depressed | Below 1 V |
| A27-35 (ST1-) - Body ground | Brake pedal is released | 11 to 14 V |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 3UR-FE) | B |
| OK (for 3UR-FBE) | C |
Reconnect the ECM connector.
A
B
C