Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DTC CHECK / CLEAR  


DTC CHECK / CLEAR (WHEN USING SST CHECK WIRE)


a.
F100115E86
1.627,0.728 2.004,0.259 false 1.849,1.429 2.245,1.937 false 0.071,0.01 1.388,0.219 1.317,0.209 10 Front view of DLC3: 2.048,0.13 2.348,0.304 0.300,0.174 10 CG 2.292,1.839 2.510,2.022 0.218,0.184 10 TC 3.297,0 3.414,0.096 0.117,0.096

Check DTC.

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Read the DTC from the ABS warning light and slip indicator light on the combination meter.

HINT:

If no code appears, inspect the TC and CG terminal circuits, and the ABS warning light and slip indicator light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)


iv.

As examples, refer to the chart below for the blinking patterns of the normal system code and trouble codes 11 and 21.

F100113E15
4.344,1.26 4.063,0.719 false 4.844,1.25 4.479,0.438 false 6.094,1.25 6.385,0.948 false 0.063,0.042 2.76,0.25 2.698,0.208 10 false Blinking Pattern in Normal System Code: 3.021,0.042 7.073,0.25 4.052,0.208 10 false Blinking Pattern in Trouble Code (Example Codes 11 and 21): 2.344,0.635 3.208,0.833 0.865,0.198 10 false 0.25 seconds 2.271,0.906 3.135,1.094 0.865,0.188 10 false 0.25 seconds 0.938,0.854 1.594,1.052 0.656,0.198 10 false 2 seconds 0.479,1.354 0.802,1.552 0.323,0.198 10 false ON 0.479,1.948 0.865,2.146 0.385,0.198 10 false OFF 2.729,1.354 3.042,1.552 0.313,0.198 10 false ON 2.729,1.948 3.094,2.146 0.365,0.198 10 false OFF 3.677,0.333 4.49,0.563 0.813,0.229 10 false 2.5 seconds 3.26,0.615 4.052,0.813 0.792,0.198 10 false 1.5 seconds 3.396,0.917 4.052,1.094 0.656,0.177 10 false 4 seconds 5.531,0.615 6.323,0.813 0.792,0.198 10 false 0.5 seconds 5.448,0.927 6.229,1.125 0.781,0.198 10 false 0.5 seconds 6.448,0.854 7.104,1.052 0.656,0.198 10 false 4 seconds 5.906,1.281 6.531,1.479 0.625,0.198 10 false Repeat 4.125,2.417 4.74,2.615 0.615,0.198 10 false DTC 11 5.167,2.396 5.771,2.604 0.604,0.208 10 false DTC 21



vi.

After completing the check, disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



b.

Clear DTC.

i.
F100115E86
1.627,0.728 2.004,0.259 false 1.849,1.429 2.245,1.937 false 0.071,0.01 1.388,0.219 1.317,0.209 10 Front view of DLC3: 2.048,0.13 2.348,0.304 0.300,0.174 10 CG 2.292,1.839 2.510,2.022 0.218,0.184 10 TC 3.297,0 3.414,0.096 0.117,0.096

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.
BR03890

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the warning light indicates a normal system code.


v.

Remove SST from the terminals of the DLC3.

HINT:

Clearing the DTCs cannot be performed by removing the battery cable or the ECU-IG No. 1 fuse.





DTC CHECK / CLEAR (WHEN USING TECHSTREAM)


a.

Check DTC.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs following the prompts on the Techstream screen.



b.

Clear DTC.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Operate the Techstream to clear the codes.

HINT:

Refer to the Techstream operator's manual for further details.





END OF DTC CHECK / CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.