Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235640 DYNAMIC LASER CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC LASER CRUISE CONTROL SYSTEM  Distance Control ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the distance control ECU. The distance control ECU determines information about the vehicle in front based on data from the laser radar sensor, and then decides how much acceleration and/or deceleration is needed to maintain the set distance. The distance control ECU also requests the skid control ECU to apply braking and to sound the buzzer.

WIRING DIAGRAM

E165055E01
2.05,1.376 2.649,1.529 0.599,0.153 10 IG1 No.3 2.907,0.625 3.762,0.776 0.856,0.151 10 ECU-IG No.2 5.757,0.405 5.884,0.577 0.127,0.172 10 1 5.926,0.485 6.058,0.641 0.132,0.156 10 B 5.692,1.933 5.877,2.102 0.185,0.169 10 10 5.914,2.033 6.345,2.192 0.431,0.159 10 SGND 5.93,3.154 6.298,3.297 0.368,0.143 10 GND 5.687,3.07 5.866,3.223 0.180,0.153 10 12 3.291,2.707 3.397,2.863 0.106,0.156 10 1 2.07,2.71 2.171,2.874 0.101,0.164 10 4 1.499,2.906 1.825,3.059 0.326,0.153 10 AM1 0.14,3.625 0.780,3.799 0.641,0.174 10 to Battery 2.261,3.217 3.186,3.387 0.925,0.170 10 Ignition switch 5.612,4.3 7.016,4.452 1.404,0.152 10 Distance Control ECU 5.612,4.159 5.877,4.298 0.265,0.139 10 A43

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DISTANCE ECU - POWER SOURCE AND GROUND)
a.
U154106E01
0.074,0.029 2.445,0.693 2.371,0.664 10 Front view of wire harness connector: (to Distance Control ECU) 1.528,1.049 1.828,1.211 0.300,0.163 10 A43 0.374,2.7 0.512,2.863 0.138,0.163 10 B 2.606,2.7 2.963,2.863 0.357,0.163 10 GND 0.776,2.005 0.443,2.682 false 2.246,2.029 1.886,2.7 false 2.698,2.012 2.801,2.7 false 1.632,2.7 2.072,2.863 0.440,0.163 10 SGND

Disconnect the A43 distance control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A43-1 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-10 (SGND) - Body ground Always Below 1 Ω
A43-12 (GND) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR