Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235640 DYNAMIC LASER CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC LASER CRUISE CONTROL SYSTEM  Wiper Signal Circuit  


DESCRIPTION

The distance control ECU detects wiper operation. If the windshield wipers operate in the HI or LO mode, the cruise control is canceled and the warning sound "pong" is emitted once. In addition, the following warnings will continue until the cruise control main switch is turned off:

·

The CRUISE main indicator light blinks.

·

The warning code "CRUISE NOT AVAILABLE" is displayed on the display in the combination meter.


After HI or LO wiper operation stops, pushing the cruise control main switch to + (ACCEL)/RES (RESUME) will resume the vehicle speed set prior to cancellation.

Cruise control is available when the windshield wipers operate in the intermittent mode.

WIRING DIAGRAM

U154122E01
0.351,1.715 0.647,1.855 0.296,0.140 10 H15 0.351,1.923 1.939,2.089 1.588,0.166 10 Windsheild Wiper Switch 1.363,1.05 1.555,1.216 0.192,0.166 10 +2 1.658,0.95 1.775,1.097 0.116,0.147 10 4 3.419,0.537 4.778,0.682 1.360,0.145 10 To Front Wiper Motor 5.484,1.692 5.780,1.851 0.296,0.159 10 A43 5.489,1.863 6.884,2.039 1.395,0.175 10 Distance Control ECU 5.732,1.042 6.101,1.209 0.369,0.168 10 WIP2 5.513,0.962 5.641,1.125 0.128,0.164 10 2

PROCEDURE

1.INSPECT WIPER SYSTEM

Check that the windshield wipers operate in HI mode.

OK:

Wiper function is normal.



OK

2.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - WINDSHIELD WIPER SWITCH)

NG

2.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - WINDSHIELD WIPER SWITCH)
a.
U154124E02
2.563,3.25 2.448,3.25 2.448,3.25 2.073,3.729 false 2.479,1.021 2.354,1.021 2.354,1.021 1.198,1.563 false 0.385,0.073 2.708,0.469 2.323,0.396 10 false Front view of wire harness connector: (to Distance Control ECU) 0.406,2.208 2.729,2.531 2.323,0.323 10 false Front view of wire harness connector: (to Windshield Wiper Switch) 0.313,1.625 0.583,1.771 0.271,0.146 10 false A43 0.688,3.833 0.958,3.99 0.271,0.156 10 false H15 2.604,3.177 2.813,3.333 0.208,0.156 10 false +2 2.521,0.938 2.906,1.104 0.385,0.167 10 false WIP2

Disconnect the A43 distance control ECU connector and H15 windshield wiper switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-2 (WIP2) - H15-4 (+2) Always Below 1 Ω
H15-4 (+2) - Body ground Always 10 kΩ or higher



c.

Reconnect the distance control ECU connector and windshield wiper switch connector.



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR