Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0717  Turbine Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, and as a result, the gears shift smoothly.

DTC Code DTC Detection Condition Trouble Area
P0717 All conditions below are detected for 5 seconds or more (1-trip detection logic)
(a) Gear change is not performed
(b) Gear position: 4th, 5th or 6th
(c) T/M input shaft rpm: Less than 300 rpm
(d) T/M output shaft rpm: 1000 rpm or more
(e) Park/neutral position switch:
·

NSW input signal is OFF

·

R input signal is OFF


(f) Shift solenoid valves and park/neutral position switch are operating normally
·

Open or short in speed sensor NT circuit

·

Speed sensor NT

·

ECM

·

Automatic transmission (clutch, brake or gear, etc.)



Inspect using an oscilloscope:

Check the waveform of the ECM connector.

C162170E04
2.707,0.097 3.292,0.298 0.585,0.201 10 1 V/DIV. 2.995,0.904 3.347,1.106 0.352,0.202 10 GND 1.637,1.688 2.453,1.883 0.816,0.195 10 2 msec./DIV.

Standard:

Refer to the illustration.


Item Content
Terminal No. (Symbol) D56-124 (NT+) - D56-123 (NT-)
Tool setting 1 V/DIV., 2 msec./DIV.
Condition Engine is idling (Shift lever in P or N)

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal comparing the input speed sensor NT with the output speed sensor SP2.

While the vehicle is operating in the 4th, 5th or 6th gear position with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
·

*1: Pulse is not output or is irregularly output.

·

*2: The vehicle speed is approximately 50 km/h (30 mph) or more.



MONITOR STRATEGY

Related DTCs P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components (Main) Speed sensor (NT)
Required sensors/Components (Related) Speed sensor (SP2)
Frequency of operation Continuous
Duration 5 seconds
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present P0705 (Park/neutral position switch circuit)
P0751, P0973, P0974 (Shift solenoid valve S1)
P0756, P0976, P0977 (Shift solenoid valve S2)
P0761, P0979, P0980 (Shift solenoid valve S3)
P0766, P0982, P0983 (Shift solenoid valve S4)
P0748 (Shift solenoid valve SL1 circuit)
P0776, P0778 (Shift solenoid valve SL2)
Shift change After shift change is completed and before starting next shift change operation
ECM selected gear 4th, 5th or 6th
Output shaft rpm 1000 rpm or more
NSW switch OFF
R switch OFF
Engine Running
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Speed sensor signal rpm Less than 300 rpm

COMPONENT OPERATING RANGE

Speed sensor signal rpm 300 rpm or more

WIRING DIAGRAM

C155187E27
5.642,1.067 6.204,1.269 0.561,0.202 10 NT+ 5.642,2.2 6.204,2.401 0.561,0.202 10 NT- 5.248,1.193 5.587,1.395 0.339,0.202 10 124 0.655,2.571 1.980,2.773 1.325,0.202 10 Speed Sensor NT 5.248,2.326 5.587,2.528 0.339,0.202 10 123 0.655,2.385 0.987,2.587 0.332,0.202 10 D43 5.83,3.014 6.162,3.216 0.332,0.202 10 D56 1.285,1.208 1.447,1.409 0.162,0.202 10 2 5.83,3.2 6.222,3.401 0.392,0.202 10 ECM 1.285,2.056 1.447,2.258 0.162,0.202 10 1

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up is:
·

ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

·

OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm

HINT:
·

SPD (NT) is always 0 while driving:

Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR NT INSTALLATION
a.
C159067E06
2.267,2.623 2.976,2.824 0.710,0.202 10 Clearance 0.341,0.443 1.166,0.645 0.825,0.202 10 CORRECT 2.186,0.443 3.205,0.645 1.020,0.202 10 INCORRECT

Check the speed sensor NT installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.




OK

2.INSPECT SPEED SENSOR NT

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR NT

2.INSPECT SPEED SENSOR NT
a.
C159420E11
0.058,0.004 2.640,0.372 2.582,0.367 10 Component without harness connected: (Speed Sensor NT) 1.346,2.308 1.577,1.709 false 2.107,2.308 1.877,1.709 false 1.248,2.309 1.426,2.511 0.178,0.202 10 2 2.096,2.309 2.246,2.511 0.150,0.202 10 1

Disconnect the D43 speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)
a.
U153472E02
1.188,2.885 1.615,2.24 true 2.115,2.875 1.698,2.229 true 0.063,0.042 2.469,0.406 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.583,1.042 1.958,1.271 0.375,0.229 10 false D56 1.813,2.885 2.51,3.083 0.698,0.198 10 false 124 (NT+) 0.771,2.885 1.427,3.083 0.656,0.198 10 false 123 (NT-)

Disconnect the D56 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-124 (NT+) - D56-123 (NT-) 20°C (68°F) 560 to 680 Ω
D56-124 (NT+) - Body ground Always 10 kΩ or higher
D56-123 (NT-) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C