Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.

The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

DTC Code DTC Detection Condition Trouble Area
P0722 All conditions below are detected 5 seconds or more continuously (2-trip detection logic)
(a) No signal from speed sensor SP2 is input to ECM
(b) Vehicle speed is 9 km/h (5.59 mph) or more
(c) Park/neutral position switch is OFF
·

Open or short in speed sensor SP2 circuit

·

Speed sensor SP2

·

ECM

·

Automatic transmission (clutch, brake or gear, etc.)



Inspect using an oscilloscope:

Check the waveform of the ECM connector.

C161208E05
2.708,0.097 3.293,0.298 0.585,0.201 10 2 V/DIV. 2.996,0.904 3.348,1.106 0.352,0.202 10 GND 1.541,1.688 2.440,1.883 0.900,0.195 10 20 msec./DIV.

Standard:

Refer to the illustration.


Item Content
Terminal No. (Symbol) D56-101 (SP2+) - D56-100 (SP2-)
Tool setting 2 V/DIV., 20 msec./DIV
Condition Vehicle speed 20 km/h (12 mph)

MONITOR DESCRIPTION

The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gear shift point and the lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.

If the ECM detects no signal from the output speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P0722: Speed sensor SP2/Verify pulse input
Required Sensors/Components Speed sensor (SP2)
Frequency of operation Continuous
Duration 5 seconds
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present None
Vehicle speed at vehicle speed sensor 9 km/h (5.59 mph) or more
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Speed sensor signal No signal

COMPONENT OPERATING RANGE

Vehicle speed at output speed sensor 9 km/h (5.59 mph) or more

WIRING DIAGRAM

C155187E28
5.642,1.067 6.204,1.269 0.561,0.202 10 SP2+ 5.642,2.2 6.204,2.401 0.561,0.202 10 SP2- 5.248,1.193 5.587,1.395 0.339,0.202 10 101 0.615,2.511 1.940,2.713 1.325,0.202 10 Speed Sensor SP2 5.248,2.326 5.587,2.528 0.339,0.202 10 100 0.615,2.326 0.947,2.528 0.332,0.202 10 D44 5.83,3.014 6.162,3.216 0.332,0.202 10 D56 1.285,1.208 1.447,1.409 0.162,0.202 10 2 5.83,3.2 6.222,3.401 0.392,0.202 10 ECM 1.285,2.056 1.447,2.258 0.162,0.202 10 1

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) -

HINT:
·

SPD (SP2) is always 0 while driving:

Open or short in the sensor or circuit.

·

The SPD (SP2) value displayed on the Techstream is much lower than the actual vehicle speed:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR SP2 INSTALLATION
a.
C159067E07
2.267,2.623 2.976,2.824 0.710,0.202 10 Clearance 0.341,0.443 1.166,0.645 0.825,0.202 10 CORRECT 2.186,0.443 3.205,0.645 1.020,0.202 10 INCORRECT

Check the speed sensor SP2 installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.




OK

2.INSPECT SPEED SENSOR SP2

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR SP2

2.INSPECT SPEED SENSOR SP2
a.
C159420E12
0.058,0.004 2.640,0.372 2.582,0.367 10 Component without harness connected: (Speed Sensor SP2) 1.346,2.308 1.577,1.709 false 2.107,2.308 1.877,1.709 false 1.248,2.309 1.426,2.511 0.178,0.202 10 2 2.096,2.309 2.246,2.511 0.150,0.202 10 1

Disconnect the D44 speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)
a.
U153473E02
1.188,2.896 1.615,2.156 true 2.125,2.885 1.708,2.146 true 0.073,0.042 2.479,0.406 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.594,1.042 1.969,1.271 0.375,0.229 10 false D56 1.781,2.906 2.531,3.104 0.75,0.198 10 false 101 (SP2+) 0.698,2.896 1.427,3.094 0.729,0.198 10 false 100 (SP2-)

Disconnect the D56 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-101 (SP2+) - D56-100 (SP2-) 20°C (68°F) 560 to 680 Ω
D56-101 (SP2+) - Body ground Always 10 kΩ or higher
D56-100 (SP2-) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C