Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235644 AUTOMATIC TRANSMISSION SYSTEM C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0705 When one of following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
·

One of the following conditions is met.

P input signal is ON

N input signal is ON

NSW input signal is ON


·

R input signal

·

D input signal


(B) Any of following signals are ON for 2.0 seconds or more in S position (2 trip detection logic):
·

P input signal

·

N input signal

·

NSW input signal

·

R input signal


(C) All signals are OFF simultaneously for P, N, NSW, R and D positions (2 trip detection logic).
·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

Transmission control switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P0705: Park/neutral position switch/Verify switch input
Required sensors/Components Park/neutral position switch
Frequency of operation Continuous
Duration Condition (A) and (B)
2 seconds
Condition (C)
60 seconds
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not present None
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: Condition (A), (B) or (C)

Condition (A)

When 2 or more of the following signals are input at the same time

One of the following conditions is met
P switch
N switch
NSW switch
ON
R switch ON
D switch ON


Condition (B)

When the shift lever is in S, one of the following conditions is met

P switch ON
N switch ON
NSW switch ON
R switch ON


Condition (C)

All of the following conditions are met

P switch OFF
N switch OFF
NSW switch OFF
R switch OFF
D switch OFF



COMPONENT OPERATING RANGE

Park/neutral position switch The park/neutral position switch sends only one signal to the ECM

WIRING DIAGRAM

C162206E18
5.448,2.375 5.771,2.573 0.323,0.198 10 false D56 5.448,2.979 5.771,3.177 0.323,0.198 10 false D56 5.448,3.573 5.771,3.771 0.323,0.198 10 false D56 5.458,4.167 5.781,4.365 0.323,0.198 10 false D56 5.458,1.208 5.781,1.406 0.323,0.198 10 false D56 5.813,5.885 5.979,6.083 0.167,0.198 10 false S 5.813,4.156 5.979,4.354 0.167,0.198 10 false P 5.813,3.563 5.979,3.76 0.167,0.198 10 false R 5.813,2.958 5.979,3.156 0.167,0.198 10 false N 5.813,2.354 5.979,2.552 0.167,0.198 10 false D 3.708,2.25 3.958,2.448 0.25,0.198 10 false DL 3.708,2.844 3.958,3.042 0.25,0.198 10 false NL 3.708,3.458 3.958,3.656 0.25,0.198 10 false RL 3.708,4.052 3.958,4.25 0.25,0.198 10 false PL 2.99,1.813 3.24,2.01 0.25,0.198 10 false B 2.99,3.156 3.24,3.354 0.25,0.198 10 false RB 0.031,3.281 1.698,3.479 1.667,0.198 10 false from Ignition Switch (IG1) 5.521,2.76 5.771,2.958 0.25,0.198 10 false 25 5.521,2.167 5.771,2.365 0.25,0.198 10 false 27 5.521,3.365 5.771,3.563 0.25,0.198 10 false 26 5.521,5.688 5.771,5.885 0.25,0.198 10 false 25 5.563,3.969 5.813,4.167 0.25,0.198 10 false 2 5.479,1 5.781,1.198 0.302,0.198 10 false 120 3.969,4.281 4.135,4.479 0.167,0.198 10 false 6 3.969,2.042 4.135,2.24 0.167,0.198 10 false 5 3.969,3.688 4.135,3.885 0.167,0.198 10 false 1 2.781,3.385 2.948,3.583 0.167,0.198 10 false 2 2.781,2.042 2.948,2.24 0.167,0.198 10 false 4 3.969,3.094 4.135,3.292 0.167,0.198 10 false 9 3.969,2.49 4.135,2.688 0.167,0.198 10 false 7 5.448,5.885 5.771,6.083 0.323,0.198 10 false A27 2.552,4.635 2.875,4.833 0.323,0.198 10 false D21 5.813,1.198 6.208,1.396 0.396,0.198 10 false NSW 6.135,7.052 6.51,7.25 0.375,0.198 10 false ECM 2.552,4.823 4.469,5.021 1.917,0.198 10 false Park/Neutral Position Switch 2.531,6.781 4.458,6.979 1.927,0.198 10 false Transmission Control Switch 0.031,5.885 1.646,6.083 1.615,0.198 10 false from Ignition Switch (IG1) 2.531,6.594 2.813,6.792 0.281,0.198 10 false H31 2.792,6 2.917,6.198 0.125,0.198 10 false 3 4,6 4.104,6.167 0.104,0.167 10 false 7 2.99,5.771 3.24,5.969 0.25,0.198 10 false IG 3.792,5.771 4.042,5.969 0.25,0.198 10 false S 3.771,1.792 4.021,1.99 0.25,0.198 10 false L 4.552,1.917 5.333,2.115 0.781,0.198 10 false to ST Relay 0.031,1.927 1.698,2.125 1.667,0.198 10 false from Ignition Switch (ST2)

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (P Range) PNP switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (R Range) PNP switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (N Range) PNP switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect



PROCEDURE

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C160109E34
2.375,2.417 2.021,1.927 true 1.615,2.427 1.708,1.938 true 1.979,2.427 1.885,1.938 true 1.625,1.667 1.542,1.177 true 1.052,2.438 1.406,1.948 true 1.823,1.677 2.188,1.188 true 1.375,1.667 1.01,1.177 true 0.052,0 2.635,0.365 2.583,0.365 10 false Component without harness connected: (Park/Neutral Position Switch) 1.365,0.958 1.573,1.135 0.208,0.177 10 false RB 0.896,1.01 1.042,1.188 0.146,0.177 10 false B 1.927,2.427 2.135,2.604 0.208,0.177 10 false PL 2.406,2.427 2.615,2.604 0.208,0.177 10 false L 1.5,2.427 1.708,2.604 0.208,0.177 10 false DL 0.896,2.406 1.104,2.583 0.208,0.177 10 false NL 2.208,0.958 2.417,1.135 0.208,0.177 10 false RL

Disconnect the D21 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever in N Below 1 Ω
2 (RB) - 7 (DL)
·

Shift lever in D

·

Shift lever in S, "+" and "-"


Below 1 Ω
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL)
·

Shift lever not in D

·

Shift lever not in S, "+" and "-"


10 kΩ or higher




OK

2.INSPECT TRANSMISSION CONTROL SWITCH

NG

2.INSPECT TRANSMISSION CONTROL SWITCH
a.
C146679E28
1.625,1.292 0.948,1.042 true 0.927,1.833 1.604,1.583 true 0.052,0 2.583,0.365 2.531,0.365 10 false Component without harness connected: (Transmission Control Switch) 0.75,0.938 1,1.135 0.25,0.198 10 false IG 0.771,1.74 0.938,1.938 0.167,0.198 10 false S

Disconnect the H31 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" and "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" and "-" 10 kΩ or higher




OK

3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
U153451E02
1.802,1.646 2.156,1.146 true 2.146,0.958 2.354,1.135 0.208,0.177 10 false RB 0.083,0.063 2.49,0.427 2.406,0.365 10 false Front view of wire harness connector: (to Park/Neutral Position Switch) 0.375,1.656 0.75,1.885 0.375,0.229 10 false D21

Disconnect the D21 park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V
D21-2 (RB) - Body ground Ignition switch off Below 1 V




OK

4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)

4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
a.
U153410E02
1.823,1.771 2.396,1.448 true 0.49,1.677 0.865,1.906 0.375,0.229 10 false H31 0.073,0.031 2.479,0.396 2.406,0.365 10 false Front view of wire harness connector: (to Transmission Control Switch) 2.438,1.323 2.677,1.521 0.24,0.198 10 false IG

Disconnect the H31 transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H31-3 (IG) - Body ground Ignition switch ON 11 to 14 V
H31-3 (IG) - Body ground Ignition switch off Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - IGNITION SWITCH)

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
U153470E02
0.208,2.906 0.573,1.677 true 2.479,2.896 1.354,2.24 true 0.708,3.188 0.573,1.771 true 1.229,2.906 0.656,1.771 true 1.844,3.177 0.74,1.76 true 0.073,0.042 2.479,0.406 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.583,1.042 1.958,1.271 0.375,0.229 10 false D56 0.031,2.896 0.417,3.094 0.385,0.198 10 false 2 (P) 2.229,2.906 2.979,3.104 0.75,0.198 10 false 120 (NSW) 1.677,3.188 2.146,3.385 0.469,0.198 10 false 27 (D) 0.5,3.188 0.948,3.385 0.448,0.198 10 false 25 (N) 1.073,2.896 1.521,3.094 0.448,0.198 10 false 26 (R)

Disconnect the D56 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
·

D56-2 (P) - Body ground

·

D56-120 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever in P


11 to 14 V
D56-26 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
·

D56-25 (N) - Body ground

·

D56-120 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever in N


11 to 14 V
D56-27 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
·

D56-2 (P) - Body ground

·

D56-120 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever not in P


Below 1 V
D56-26 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
·

D56-25 (N) - Body ground

·

D56-120 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever not in N


Below 1 V
D56-27 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V


HINT:

*: The voltage will drop slightly due to turning on the back-up light.




OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U153484E02
2.281,2.885 1.979,1.833 true 0.073,0.052 2.479,0.417 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.677,1.042 2.052,1.271 0.375,0.229 10 false A27 2.125,2.906 2.594,3.104 0.469,0.198 10 false 25 (S)

Disconnect the A27 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-25 (S) - Body ground Shift lever in S, "+" and "-" 11 to 14 V
A27-25 (S) - Body ground Shift lever not in S, "+" and "-" Below 1 V


Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C