Home › Drivetrain › AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION WIRE
RM27L0U _52 Drivetrain _049310 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0235647 TRANSMISSION WIRE A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


PROCEDURE

Hide 82125J 1.INSTALL TRANSMISSION WIRE

a.

Coat the O-ring of the transmission wire connector with ATF.


b.
C161102

Install the 2 transmission wires with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
U152295

Connect the 2 transmission wire connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



Hide 82125J 2.CONNECT TRANSMISSION WIRE

a.
U152299E02
1.198,0.896 0.719,0.604 true 1.135,1.167 0.417,1.24 true 0.24,0.49 0.719,0.708 0.479,0.219 10 true Orange 0.125,1.167 0.438,1.375 0.313,0.208 10 true Blue 0.906,0.313 1.042,0.5 0.135,0.188 10 true A 0.729,1.375 0.865,1.552 0.135,0.177 10 true B

Connect the 9 connectors to the solenoid valves.


b.

Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

·

for bolt A


Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

·

for bolt B


Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

12 mm (0.472 in.) for bolt A


36 mm (1.41 in.) for bolt B


Hide 35330 3.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the oil strainer.


b.
C178807

Install the oil strainer with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35106 4.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.
C178809E05
0.656,0.115 0.802,0.115 0.802,0.115 2.198,1.031 true 1.698,1.021 0.802,0.115 false 1.042,0.76 0.802,0.115 false 1.021,1.271 0.802,0.115 true 0.167,0.031 0.698,0.219 0.531,0.188 10 false Magnet

Install the 4 transmission oil cleaner magnets to the oil pan.


b.
C353371

Install a new gasket and the oil pan with the 12 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:
C157303E01
0.362,0.23 1.147,0.423 0.786,0.193 10 CORRECT 1.669,0.23 2.566,0.414 0.897,0.184 10 INCORRECT 2.374,2.599 3.071,2.788 0.698,0.188 10 Protrusion 2.584,3.417 3.087,3.607 0.503,0.191 10 Sleeve 1.899,3.782 2.416,3.507 2.416,3.507 2.544,3.507 false

·

Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.

·

Install the gasket so that there is no slack in the gasket, and make sure the seal surface's entire circumference is level.

·

Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.

·

When tightening the oil pan, make sure that the gasket is not pinched between the gasket tightening area's sleeve and the transmission's seal surface.




Hide 6.ADJUST AUTOMATIC TRANSMISSION FLUID

Hide 7.INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK