Home › Drivetrain › JF3A TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27L0U _52 Drivetrain _049312 JF3A TRANSFER / 4WD / AWD _0235671 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM G

JF3A TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT INDICATOR LIGHT

a.

4HI Indicator Light:

i.

Turn the ignition switch to ON.


ii.

Change the 4WD control switch from 2WD to 4H. Then move the shift lever to N (vehicle is stopped).


iii.
C159463E02
0.985,0.028 2.244,0.209 1.260,0.181 10 4WD Control Switch 2.291,3.006 2.587,3.188 0.297,0.181 10 ON 0.864,3.006 1.244,3.188 0.380,0.181 10 Blink

Check the 4HI indicator light.

OK:

4HI indicator light comes on or 4HI indicator light comes on after blinking


HINT:

If there is a malfunction, inspect the switch, ECU, transfer shift actuator and A.D.D. actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).




b.

4LO Indicator Light:

i.

Turn the ignition switch to ON.


ii.

Change the 4WD control switch from 2WD to 4H. Then move the shift lever to N (vehicle is stopped) after the 4HI indicator light illuminates.


iii.

Change the 4WD control switch from 4H to 4L.


iv.
C159462E02
2.327,3.076 2.679,3.258 0.352,0.181 10 ON 0.917,3.076 1.270,3.258 0.352,0.181 10 Blink 0.934,0.017 2.194,0.198 1.260,0.181 10 4WD Control Switch

Check the 4LO indicator light.

OK:

4LO indicator light comes on or 4LO indicator light comes on after blinking


HINT:

If there is a malfunction, inspect the switch, ECU, transfer shift actuator and A.D.D. actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).




c.

CENTER DIFF. Indicator Light:

i.

Turn the ignition switch to ON.


ii.

Change the 4WD control switch from 2WD to 4H. Then move the shift lever to N (vehicle is stopped). (4HI indicator light illuminates).


iii.

Press the center differential lock switch.


iv.

Check the CENTER DIFF. indicator light.

U153605E01
1.234,0.054 2.494,0.235 1.260,0.181 10 4WD Control Switch 4.624,0.054 6.540,0.235 1.916,0.181 10 Center Differential Lock Switch 1.759,2.133 1.776,2.196 0.017,0.063 1.787,2.133 1.811,2.196 0.025,0.063 5.455,2.137 5.472,2.2 0.017,0.063 5.484,2.137 5.508,2.2 0.025,0.063 4.954,2.068 5.086,2.068 false 4.954,2.253 5.086,2.253 false 4.966,2.034 4.929,2.091 false 5.109,2.044 5.072,2.101 false 5.019,2.077 5.019,2.119 false 5.019,2.201 5.019,2.243 false 4.945,2.217 4.945,2.289 false 5.092,2.219 5.092,2.29 false 4.999,2.139 5.044,2.182 false 5.043,2.14 4.996,2.184 false 6.046,2.068 6.179,2.068 false 6.046,2.253 6.179,2.253 false 6.059,2.034 6.022,2.091 false 6.202,2.044 6.165,2.101 false 6.112,2.077 6.112,2.119 false 6.112,2.201 6.112,2.243 false 6.038,2.217 6.038,2.289 false 6.185,2.219 6.185,2.29 false 6.091,2.139 6.136,2.182 false 6.136,2.14 6.089,2.184 false 6.009,2.445 6.395,2.626 0.386,0.181 10 ON 4.874,2.445 5.260,2.626 0.386,0.181 10 OFF 2.292,2.417 2.677,2.598 0.386,0.181 10 ON 1.157,2.417 1.543,2.598 0.386,0.181 10 Blink

OK:

CENTER DIFF. indicator light comes on or CENTER DIFF. indicator light comes on after it is blinking


HINT:

If there is a malfunction, inspect the switches, ECU, transfer, and shift actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).




Hide 2.INSPECT FUSE (4WD)

a.
U153611E01
0.109,0.061 1.192,0.242 1.083,0.181 10 Main Body ECU: 2.128,2.127 2.128,2.71 false 1.953,2.742 2.293,2.923 0.340,0.181 10 4WD

Remove the 4WD fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4WD fuse Always Below 1 Ω


HINT:

If a fuse is blown, inspect the harness connected to the fuse for a short circuit, and repair or replace the harness and replace the fuse.



Hide 89533A 3.INSPECT 4WD CONTROL ECU (POWER SUPPLY)

a.
U153504E02
2.177,1.958 1.938,2.677 true 1.844,1.354 2.292,1.958 true 0.188,0.219 2.531,0.615 2.344,0.396 10 false Component with harness connected: (4WD Control ECU) 2.365,1.458 2.677,1.615 0.313,0.156 10 false A29 1.635,1.208 1.854,1.375 0.219,0.167 10 false IG 1.729,2.698 2.125,2.917 0.396,0.219 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-3 (IG) - Body ground Ignition switch ON 11 to 14 V


HINT:

If there is a malfunction, inspect the harness or connector. If the harness is malfunctioning, repair or replace harness or connector. If the harness or connector is normal, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-4 (GND) - Body ground Always Below 1 Ω


HINT:

If there is a malfunction, repair or replace the harness or connector.



Hide 89533A 4.INSPECT 4WD CONTROL ECU (4WD CONTROL SWITCH)

a.
U153505E01
0.188,0.054 2.539,0.453 2.350,0.399 10 Component with harness connected: (4WD Control ECU) 1.114,1.428 1.423,1.584 0.309,0.156 10 A28 1.633,2.79 1.877,2.965 0.244,0.174 10 2-4 0.504,2.79 0.754,2.955 0.250,0.165 10 LO 1.248,2.043 1.75,2.79 false 1.094,2.048 0.608,2.79 false 1.248,2.043 1.75,2.79 false 1.094,2.048 0.608,2.79 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A28-11 (2-4) - Body ground Ignition switch ON
4WD control switch 2WD
Below 1.5 V
Ignition switch ON
4WD control switch 4H
Below 1.5 V
Ignition switch ON
4WD control switch 4L
10.5 to 14 V
A28-13 (LO) - Body ground Ignition switch ON
4WD control switch 2WD
10.5 to 14 V
Ignition switch ON
4WD control switch 4H
Below 1.5 V
Ignition switch ON
4WD control switch 4L
Below 1.5 V


HINT:

If there is a malfunction, check the power supply. If the power supply is normal, inspect the 4WD control switch (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL SWITCH>ON-VEHICLE INSPECTION).



Hide 89533A 5.INSPECT 4WD CONTROL ECU (CENTER DIFFERENTIAL LOCK SWITCH)

a.
U153506E01
0.188,0.066 2.539,0.465 2.350,0.399 10 Component with harness connected: (4WD Control ECU) 1.114,1.441 1.423,1.597 0.309,0.156 10 A28 0.504,2.802 0.754,2.967 0.250,0.165 10 DL 1.162,2.06 0.608,2.802 false 1.162,2.06 0.608,2.802 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A28-12 (DL) - Body ground Ignition switch ON
Center differential lock switch ON
Below 1.5 V
Ignition switch ON
Center differential lock switch OFF
10.5 to 14 V


HINT:

If there is a malfunction, check the power supply. If the power supply is normal, inspect the center differential lock switch (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>CENTER DIFFERENTIAL LOCK SWITCH>INSPECTION).



Hide 36410J 6.INSPECT MULTI MODE TRANSFER SHIFT ACTUATOR

HINT:

After inspecting the power supply, 4WD control switch and center differential lock switch, inspect the multi mode transfer shift actuator.


a.

Check the harness and connector (ECU - multi mode transfer shift actuator).

i.

Disconnect the D45 actuator connector.


ii.

Disconnect the A28 and A29 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

U153516E02
1.115,1.76 1.115,2.323 true 1.021,1.76 0.771,2.323 true 1.229,1.771 1.469,2.333 true 1.844,1.76 2.094,2.323 true 3.448,1.917 3.323,2.302 true 3.635,1.906 3.76,2.292 true 5.427,1.917 5.302,2.344 true 5.646,1.917 5.646,2.344 true 5.083,1.906 4.604,2.333 true 5.823,1.917 6.01,2.344 true 6.01,1.906 6.333,2.333 true 6.188,1.906 6.667,2.333 true 5.25,1.917 4.917,2.323 true 1.104,0.208 3.438,0.708 2.333,0.5 10 false Front view of wire harness connectors: (to 4WD Control ECU) 4.479,0.208 6.781,0.75 2.302,0.542 10 false Front view of wire harness connector: (to Multi Mode Transfer Shift Actuator) 1.344,1.156 1.677,1.354 0.333,0.198 10 false A28 3.417,1.125 3.708,1.323 0.292,0.198 10 false A29 5.573,1.031 5.906,1.229 0.333,0.198 10 false D45 3.656,2.344 4.01,2.542 0.354,0.198 10 false TM1 3.177,2.344 3.563,2.521 0.385,0.177 10 false TM2 0.625,2.354 0.979,2.573 0.354,0.219 10 false TL1 0.99,2.354 1.344,2.573 0.354,0.219 10 false TL2 1.385,2.354 1.677,2.521 0.292,0.167 10 false TL3 1.979,2.354 2.448,2.573 0.469,0.219 10 false 4WD 4.448,2.323 4.771,2.5 0.323,0.177 10 false TM1 4.781,2.344 5.094,2.51 0.313,0.167 10 false TM2 5.542,2.344 5.833,2.5 0.292,0.156 10 false TL1 5.917,2.344 6.208,2.5 0.292,0.156 10 false TL3 6.229,2.333 6.521,2.5 0.292,0.167 10 false TL2 5.156,2.344 5.51,2.51 0.354,0.167 10 false CDL 6.542,2.333 6.99,2.615 0.448,0.281 10 false GND1

Standard Resistance:
Tester Connection Condition Specified Condition
A28-6 (TL1) - D45-4 (TL1) Always Below 1 Ω
A28-6 (TL1) - Body ground Always 10 kΩ or higher
A28-7 (TL2) - D45-6 (TL2) Always Below 1 Ω
A28-7 (TL2) - Body ground Always 10 kΩ or higher
A28-8 (TL3) - D45-5 (TL3) Always Below 1 Ω
A28-8 (TL3) - Body ground Always 10 kΩ or higher
A28-14 (4WD) - D45-3 (CDL) Always Below 1 Ω
A28-14 (4WD) - Body ground Always 10 kΩ or higher
A29-7 (TM2) - D45-2 (TM2) Always Below 1 Ω
A29-7 (TM2) - Body ground Always 10 kΩ or higher
A29-8 (TM1) - D45-1 (TM1) Always Below 1 Ω
A29-8 (TM1) - Body ground Always 10 kΩ or higher
D45-7 (GND1) - Body ground Always Below 1 Ω


HINT:

If there is a malfunction, repair or replace harness or connector. If the harness or connector is normal, check the ECU output voltage.




b.

Check the 4WD control ECU (multi mode transfer shift actuator).

i.

Connect the A28 and A29 ECU connectors.


ii.

Connect the D45 actuator connector.


iii.
U153507E02
1.021,2.042 0.333,2.906 true 1.448,2.031 0.906,2.896 true 1.531,2.031 1.302,2.896 true 1.594,2.031 1.688,2.896 true 2.188,1.99 2.188,2.896 true 2.448,2.135 2.719,2.896 true 2.573,2.135 3.104,2.896 true 0.188,0.188 2.51,0.583 2.323,0.396 10 false Component with harness connected: (4WD Control ECU) 1.135,1.469 1.448,1.625 0.313,0.156 10 false A28 2.354,1.458 2.667,1.615 0.313,0.156 10 false A29 1.573,2.927 1.854,3.104 0.281,0.177 10 false TL1 0.74,2.927 1.031,3.094 0.292,0.167 10 false TL3 1.156,2.927 1.448,3.094 0.292,0.167 10 false TL2 2.563,2.927 2.865,3.094 0.302,0.167 10 false TM1 2.969,2.927 3.281,3.083 0.313,0.156 10 false TM2 0.146,2.927 0.49,3.073 0.344,0.146 10 false 4WD 1.99,2.927 2.333,3.115 0.344,0.188 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-8 (TM1) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD → 4H or 4L (During operation of Multi mode transfer shift actuator motor from 2WD to 4WD HIGH or 4WD LOW)
10 to 14 V
Ignition switch ON
4WD control switch 2WD → 4H or 4L (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
A29-7 (TM2) - A29-4 (GND) Ignition switch ON
4WD control switch 4H or 4L → 2WD (During operation of Multi mode transfer shift actuator motor from 4WD HIGH or 4WD LOW to 2WD)
10 to 14 V
Ignition switch ON
4WD control switch 4H or 4L → 2WD (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
A28-6 (TL1) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD
Below 1.5 V
Ignition switch ON
4WD control switch 4H or 4L
10.5 to 14 V
A28-7 (TL2) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD
10.5 to 14 V
Ignition switch ON
4WD control switch 4H or 4L
Center differential Lock
10.5 to 14 V
Ignition switch ON
4WD control switch 4H or 4L
Center differential Free
Below 1.5 V
A28-8 (TL3) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD
10.5 to 14 V
Ignition switch ON
4WD control switch 4H or 4L
Center differential Lock
Below 1.5 V
Ignition switch ON
4WD control switch 4H or 4L
Center differential Free
10.5 to 14 V
A28-14 (4WD) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD
9.5 to 14 V
Ignition switch ON
4WD control switch 4H or 4L
Center differential Lock
Below 1.5 V
Ignition switch ON
4WD control switch 4H or 4L
Center differential Free
9.5 to 14 V


HINT:

If there is a malfunction, determine if the malfunction is on the ECU side or the actuator side by disconnecting the connector of the multi mode transfer shift actuator, and then checking the ECU output voltage.




c.

Check the 4WD control ECU.

i.

Disconnect the D45 actuator connector.


ii.

Connect the A28 and A29 ECU connectors.


iii.
U153523E01
0.324,0.103 2.793,0.849 2.469,0.746 10 Front view of wire harness connector: (to Multi Mode Transfer Shift Actuator) 0.214,1.323 0.513,1.488 0.299,0.165 10 D45 0.782,3.009 1.124,3.153 0.342,0.144 10 CDL 1.257,3.009 1.557,3.157 0.299,0.148 10 TL1 2.168,3.009 2.468,3.157 0.299,0.148 10 TL2 1.779,3.009 2.092,3.158 0.313,0.150 10 TL3 2.563,3.009 3.002,3.183 0.438,0.174 10 GND1 1.689,2.275 1.396,2.956 false 1.448,2.275 0.967,2.956 false 1.912,2.275 1.912,2.956 false 2.153,2.275 2.29,2.956 false 2.359,2.275 2.737,2.956 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D45-3 (CDL) - D45-7 (GND1) Ignition switch ON 9.5 to 14 V
D45-4 (TL1) - D45-7 (GND1) Ignition switch ON 10.5 to 14 V
D45-6 (TL2) - D45-7 (GND1) Ignition switch ON 10.5 to 14 V
D45-5 (TL3) - D45-7 (GND1) Ignition switch ON 10.5 to 14 V


HINT:

If there is a malfunction, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL). If the voltage is normal, inspect the multi mode transfer shift actuator, because the voltage applied to the motor cannot be measured.




d.

Inspect the multi mode transfer shift actuator.

i.

Remove the transfer shift actuator (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY).


ii.

Check the 2WD to 4WD HIGH (H4L) switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 2WD to 4WD HIGH (H4L) position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When inspecting the operation described above, use the stop light control relay (BRK NO. 1).


U153526E02
6.021,1 6.021,0.75 false 6.708,1.594 6.24,1.594 false 6.708,1.99 6.229,1.99 false 5.771,1.01 5.604,0.76 false 6.302,1 6.469,0.75 false 1.302,2.208 1.302,2.49 false 1.438,2.208 1.646,2.49 false 1.563,2.208 2,2.49 false 1.688,2.208 2.365,2.49 false 1.177,2.208 1.021,2.49 false 1.052,2.208 0.708,2.49 false 0.917,2.208 0.365,2.49 false 4.719,0.115 7.115,0.313 2.396,0.198 10 false Stop Light Control Relay (BRK NO. 1): 5.573,0.573 5.76,0.75 0.188,0.177 10 false 1 6.427,0.573 6.594,0.771 0.167,0.198 10 false 2 6,0.573 6.25,0.74 0.25,0.167 10 false 4 6.76,1.5 6.927,1.688 0.167,0.188 10 false 5 6.76,1.896 6.927,2.052 0.167,0.156 10 false 3 0.073,0.063 2.854,0.521 2.781,0.458 10 false Component without wire harness connector: (Multi Mode Transfer Shift Actuator) 2.25,2.531 2.625,2.688 0.375,0.156 10 false TM1 1.896,2.531 2.24,2.698 0.344,0.167 10 false TM2 0.583,2.531 0.896,2.698 0.313,0.167 10 false TL2 0.896,2.531 1.208,2.698 0.313,0.167 10 false TL3 1.198,2.531 1.51,2.698 0.313,0.167 10 false TL1 1.542,2.531 1.906,2.698 0.365,0.167 10 false CDL 0.125,2.531 0.542,2.698 0.417,0.167 10 false GND1 0.115,0.75 1.885,0.938 1.771,0.188 10 false 2WD to 4WD HIGH (H4F):

1.

After the 2WD to 4WD HIGH (H4F) switch is complete, inspect the 4WD detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CDL) - 7 (GND1) After 2WD to 4WD HIGH (H4F) switch is complete 100 kΩ or higher
4 (TL1) - 7 (GND1) After 2WD to 4WD HIGH (H4F) switch is complete 100 kΩ or higher
5 (TL3) - 7 (GND1) After 2WD to 4WD HIGH (H4F) switch is complete 100 kΩ or higher
6 (TL2) - 7 (GND1) After 2WD to 4WD HIGH (H4F) switch is complete Below 1 Ω




iii.

Check the 4WD HIGH (H4F) to 2WD switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD HIGH (H4F) to 2WD position.

U153527E02
5.927,1.281 5.927,1.031 false 6.604,1.865 6.125,1.865 false 6.604,2.271 6.135,2.271 false 5.688,1.302 5.51,1.052 false 6.198,1.281 6.365,1.031 false 1.219,2.188 1.219,2.469 false 1.354,2.188 1.563,2.469 false 1.479,2.188 1.917,2.469 false 1.604,2.188 2.281,2.469 false 1.094,2.188 0.948,2.469 false 0.969,2.188 0.646,2.469 false 0.833,2.188 0.344,2.469 false 4.688,0.406 7.083,0.604 2.396,0.198 10 false Stop Light Control Relay (BRK NO. 1): 5.479,0.865 5.667,1.042 0.188,0.177 10 false 1 6.333,0.865 6.5,1.063 0.167,0.198 10 false 2 5.906,0.865 6.156,1.031 0.25,0.167 10 false 4 6.667,1.802 6.833,1.99 0.167,0.188 10 false 5 6.667,2.198 6.833,2.354 0.167,0.156 10 false 3 0.063,0.042 2.844,0.5 2.781,0.458 10 false Component without wire harness connector: (Multi Mode Transfer Shift Actuator) 2.167,2.51 2.542,2.667 0.375,0.156 10 false TM1 1.813,2.51 2.156,2.677 0.344,0.167 10 false TM2 0.51,2.51 0.823,2.677 0.313,0.167 10 false TL2 0.823,2.51 1.135,2.677 0.313,0.167 10 false TL3 1.115,2.51 1.427,2.677 0.313,0.167 10 false TL1 1.458,2.51 1.823,2.677 0.365,0.167 10 false CDL 0.063,2.521 0.51,2.688 0.448,0.167 10 false GND1 0.104,0.729 1.792,0.917 1.688,0.188 10 false 4WD HIGH (H4F) to 2WD:

1.

After the 4WD HIGH (H4F) to 2WD switch is complete, inspect the 4WD detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CDL) - 7 (GND1) After 4WD HIGH (H4F) to 2WD switch is complete 100 kΩ or higher
4 (TL1) - 7 (GND1) After 4WD HIGH (H4F) to 2WD switch is complete Below 1 Ω
5 (TL3) - 7 (GND1) After 4WD HIGH (H4F) to 2WD switch is complete 100 kΩ or higher
6 (TL2) - 7 (GND1) After 4WD HIGH (H4F) to 2WD switch is complete 100 kΩ or higher


HINT:

If there is a malfunction, replace the transfer shift actuator (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY). If the transfer shift actuator is normal, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).





Hide 41400 7.INSPECT A.D.D. ACTUATOR

HINT:

After inspecting the multi mode transfer shift actuator, inspect the A.D.D. actuator.


a.

Check the harness and connector (ECU - A.D.D. actuator).

i.

Disconnect the A28 and A29 ECU connectors.


ii.

Disconnect the F1 actuator connector.


iii.

Measure the resistance according to the value(s) in the table below.

U153519E02
1.323,1.76 1.094,2.281 false 1.438,1.75 1.677,2.271 false 1.948,1.75 2.188,2.271 false 3.135,1.719 3.604,2.26 false 5.333,1.885 5.031,2.313 false 5.521,1.875 5.375,2.302 false 5.698,1.875 5.698,2.302 false 3.125,1.958 3.125,2.302 false 5.896,1.865 6.083,2.292 false 6.083,1.865 6.396,2.292 false 6.26,1.865 6.74,2.292 false 1.104,0.229 3.427,0.698 2.323,0.469 10 false Front view of wire harness connectors: (to 4WD Control ECU) 4.479,0.219 6.75,0.719 2.271,0.5 10 false Front view of wire harness connector: (to A.D.D. Actuator) 1.344,1.156 1.677,1.354 0.333,0.198 10 false A28 3.417,1.104 3.75,1.302 0.333,0.198 10 false A29 5.688,1.031 6.021,1.229 0.333,0.198 10 false F1 3.49,2.313 3.844,2.51 0.354,0.198 10 false DM1 3.01,2.313 3.396,2.49 0.385,0.177 10 false DM2 0.979,2.323 1.333,2.542 0.354,0.219 10 false DL1 1.583,2.323 1.875,2.49 0.292,0.167 10 false DL2 2.052,2.333 2.521,2.552 0.469,0.219 10 false ADD 4.844,2.354 5.156,2.521 0.313,0.167 10 false DM1 5.552,2.344 5.875,2.5 0.323,0.156 10 false ADD 5.948,2.344 6.271,2.5 0.323,0.156 10 false GND 6.313,2.333 6.604,2.5 0.292,0.167 10 false DL2 5.198,2.354 5.552,2.521 0.354,0.167 10 false DM2 6.656,2.323 7.052,2.604 0.396,0.281 10 false DL1

Standard Resistance:
Tester Connection Condition Specified Condition
A28-9 (DL1) - F1-6 (DL1) Always Below 1 Ω
A28-9 (DL1) - Body ground Always 100 kΩ or higher
A28-10 (DL2) - F1-5 (DL2) Always Below 1 Ω
A28-10 (DL2) - Body ground Always 100 kΩ or higher
A28-15 (ADD) - F1-3 (ADD) Always Below 1 Ω
A28-15 (ADD) - Body ground Always 100 kΩ or higher
A29-1 (DM1) - F1-1 (DM1) Always Below 1 Ω
A29-1 (DM1) - Body ground Always 100 kΩ or higher
A29-5 (DM2) - F1-2 (DM2) Always Below 1 Ω
A29-5 (DM2) - Body ground Always 100 kΩ or higher
F1-4 (GND) - Body ground Always Below 1 Ω


HINT:

If there is a malfunction, repair or replace harness or connector. If the harness or connector is normal, check the ECU output voltage.




b.

Check the 4WD control ECU (A.D.D. actuator).

i.

Connect the A28 and A29 ECU connectors.


ii.

Connect the F1 actuator connector.


iii.
U153509E02
0.948,2.052 0.26,2.917 true 1.313,2.031 0.76,2.896 true 1.375,2.031 1.458,2.896 true 2.177,2 2.177,2.906 true 2.813,2.135 2.813,2.896 true 2.813,1.781 2.813,1.969 true 0.188,0.146 2.51,0.542 2.323,0.396 10 false Component with harness connected: (4WD Control ECU) 1.146,1.469 1.458,1.625 0.313,0.156 10 false A28 2.365,1.26 2.677,1.417 0.313,0.156 10 false A29 1.354,2.927 1.635,3.104 0.281,0.177 10 false DL1 0.604,2.927 0.896,3.094 0.292,0.167 10 false DL2 2.667,2.927 2.979,3.094 0.313,0.167 10 false DM2 2.667,1.583 2.979,1.74 0.313,0.156 10 true DM1 0.073,2.927 0.417,3.073 0.344,0.146 10 false ADD 1.99,2.927 2.333,3.115 0.344,0.188 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-1 (DM1) - A29-4 (GND) Ignition switch ON
4WD control switch 4H (During operation of A.D.D. actuator from Lock to Free)
10 to 14 V
Ignition switch ON
4WD control switch 4H (A.D.D. actuator Free)
Below 1.5 V
A29-5 (DM2) - A29-4 (GND) Ignition switch ON
4WD control switch 4H (during operation of A.D.D. actuator from Free to Lock)
10 to 14 V
Ignition switch ON
4WD control switch 4H (A.D.D. actuator Lock)
Below 1.5 V
A28-9 (DL1) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD (A.D.D. actuator Free)
10.5 to 14 V
Ignition switch ON
4WD control switch 4H (A.D.D. actuator Lock)
Below 1.5 V
A28-10 (DL2) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD (A.D.D. actuator Free)
Below 1.5 V
Ignition switch ON
4WD control switch 4H (A.D.D. actuator Lock)
10.5 to 14 V
A28-15 (ADD) - A29-4 (GND) Ignition switch ON
4WD control switch 2WD
10 to 14 V
Ignition switch ON
4WD control switch 4H or 4L
Below 1.5 V


HINT:

If there is a malfunction, determine if the malfunction is on the ECU side or the actuator side by disconnecting the connector of the A.D.D. actuator, and then checking the ECU output voltage.




c.

Check the 4WD control ECU.

i.

Connect the A28 and A29 ECU connectors.


ii.

Disconnect the F1 actuator connector.


iii.
C160511E02
0.433,0.0090 2.902,0.756 2.469,0.746 10 Front view of wire harness connector: (to A. D. D. Actuator) 0.277,1.191 0.666,1.434 0.39,0.244 0.374,1.23 0.57,1.395 0.196,0.165 10 F1 0.822,2.915 1.164,3.06 0.342,0.145 10 DM2 1.314,2.915 1.643,3.064 0.329,0.149 10 ADD 2.621,2.915 2.92,3.064 0.3,0.149 10 DL2 2.087,2.915 2.434,3.065 0.347,0.15 10 GND 3.102,2.915 3.386,3.09 0.285,0.175 10 DL1 1.797,2.164 1.505,2.863 false 1.557,2.164 1.041,2.863 false 0.34,2.915 0.683,3.06 0.342,0.145 10 DM1 1.333,2.164 0.577,2.863 false 2.055,2.164 2.279,2.863 false 2.296,2.164 2.743,2.863 false 2.519,2.164 3.207,2.863 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-3 (ADD) - F1-4 (GND) Ignition switch ON 10 to 14 V
F1-5 (DL2) - F1-4 (GND) Ignition switch ON 10.5 to 14 V
F1-6 (DL1) - F1-4 (GND) Ignition switch ON 10.5 to 14 V


HINT:

If there is a malfunction, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL). If the voltage is normal, inspect the A.D.D. actuator, because the voltage applied to the motor cannot be measured.




d.

Inspect the A.D.D. actuator.


ii.

Check the Free to Lock switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the Free to the Lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When inspecting the operation described above, use the stop light control relay (BRK NO. 1).


C160576E03
5.938,1.094 5.938,0.844 false 6.625,1.677 6.156,1.677 false 6.625,2.073 6.146,2.073 false 5.708,1.094 5.542,0.844 false 6.219,1.094 6.385,0.854 false 1.583,2.302 1.427,2.5 false 1.396,2.302 1.063,2.5 false 1.24,2.302 0.698,2.5 false 1.781,2.302 1.938,2.5 false 1.969,2.302 2.302,2.5 false 2.146,2.302 2.688,2.5 false 4.635,0.198 7.031,0.396 2.396,0.198 10 false Stop Light Control Relay (BRK NO. 1): 5.49,0.656 5.677,0.833 0.188,0.177 10 false 1 6.354,0.656 6.521,0.854 0.167,0.198 10 false 2 5.917,0.656 6.167,0.823 0.25,0.167 10 false 4 6.677,1.594 6.844,1.781 0.167,0.188 10 false 5 6.677,1.99 6.844,2.146 0.167,0.156 10 false 3 0.094,0.063 2.875,0.521 2.781,0.458 10 false Component without wire harness connector: (A. D. D. Actuator) 2.604,2.552 2.979,2.708 0.375,0.156 10 false DM1 2.219,2.552 2.563,2.719 0.344,0.167 10 false DM2 0.896,2.552 1.208,2.719 0.313,0.167 10 false DL2 1.26,2.552 1.594,2.719 0.333,0.167 10 false GND 1.823,2.552 2.188,2.719 0.365,0.167 10 false ADD 0.521,2.552 0.896,2.719 0.375,0.167 10 false DL1 0.135,0.75 1.771,0.938 1.635,0.188 10 false Free to Lock:

1.

After the Free to Lock switch is complete, inspect the A.D.D. detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ADD) - 4 (GND) After Free to Lock switch is complete Below 1 Ω
5 (DL2) - 4 (GND) After Free to Lock switch is complete 100 kΩ or higher
6 (DL1) - 4 (GND) After Free to Lock switch is complete Below 1 Ω




iii.

Check the Lock to Free switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the Lock to the Free position.

C160577E03
5.792,1.146 5.792,0.896 false 6.479,1.719 6,1.719 false 6.469,2.125 6,2.125 false 5.542,1.135 5.375,0.885 false 6.052,1.146 6.219,0.896 false 1.594,2.302 1.438,2.5 false 1.406,2.302 1.073,2.5 false 1.25,2.302 0.698,2.5 false 1.781,2.302 1.938,2.5 false 1.958,2.302 2.302,2.5 false 2.135,2.302 2.688,2.5 false 4.479,0.25 6.875,0.448 2.396,0.198 10 false Stop Light Control Relay (BRK NO. 1): 5.323,0.708 5.51,0.885 0.188,0.177 10 false 1 6.198,0.708 6.365,0.906 0.167,0.198 10 false 2 5.771,0.708 6.021,0.875 0.25,0.167 10 false 4 6.521,1.646 6.688,1.833 0.167,0.188 10 false 5 6.521,2.042 6.688,2.198 0.167,0.156 10 false 3 0.104,0.104 2.885,0.563 2.781,0.458 10 false Component without wire harness connector: (A. D. D. Actuator) 2.594,2.542 2.969,2.698 0.375,0.156 10 false DM1 2.219,2.542 2.563,2.708 0.344,0.167 10 false DM2 0.906,2.542 1.219,2.708 0.313,0.167 10 false DL2 1.271,2.542 1.604,2.708 0.333,0.167 10 false GND 1.823,2.542 2.188,2.708 0.365,0.167 10 false ADD 0.531,2.542 0.906,2.708 0.375,0.167 10 false DL1 0.146,0.792 1.781,0.979 1.635,0.188 10 false Lock to Free:

1.

After the Lock to Free switch is complete, inspect the A.D.D. detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ADD) - 4 (GND) After Lock to Free switch is complete 100 kΩ or higher
5 (DL2) - 4 (GND) After Lock to Free switch is complete Below 1 Ω
6 (DL1) - 4 (GND) After Lock to Free switch is complete 100 kΩ or higher


If there is a malfunction, replace the A.D.D. actuator (See page Drivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR(for 4WD)>REMOVAL). If the A.D.D. actuator is normal, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).




Hide 36410J 8.INSPECT HIGH-LOW TRANSFER SHIFT ACTUATOR

HINT:

Before the inspection, check that the system is switched from 2WD to 4WD normally.


a.

Check the harness and connector (ECU - high-low transfer shift actuator).

i.

Disconnect the D46 high-low transfer shift actuator connector.


ii.

Disconnect the A28 and A29 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

U153518E02
3.396,1.927 3.396,2.313 false 3.396,1.75 3.99,2.333 false 0.688,1.781 0.688,2.344 false 2.146,1.771 2.146,2.333 false 0.594,1.792 0.344,2.354 false 0.802,1.781 1.052,2.344 false 5.188,1.813 4.708,2.24 false 5.365,1.844 5.073,2.271 false 5.552,1.844 5.427,2.271 false 5.75,1.865 5.75,2.292 false 5.188,1.844 4.708,2.271 false 5.927,1.844 6.104,2.271 false 6.104,1.833 6.427,2.26 false 6.292,1.833 6.771,2.26 false 1.188,0.135 3.5,0.594 2.313,0.458 10 false Front view of wire harness connectors: (to 4WD Control ECU) 4.573,0.115 6.875,0.625 2.302,0.51 10 false Front view of wire harness connector: (to High-Low Transfer Shift Actuator) 1.438,1.167 1.771,1.365 0.333,0.198 10 false A28 3.51,1.135 3.844,1.333 0.333,0.198 10 false A29 5.698,1.052 6.031,1.25 0.333,0.198 10 false D46 3.865,2.354 4.219,2.552 0.354,0.198 10 false HM1 3.24,2.333 3.625,2.51 0.385,0.177 10 false HM2 2.073,2.365 2.302,2.521 0.229,0.156 10 false NP 0.229,2.375 0.583,2.594 0.354,0.219 10 false HL1 0.573,2.365 0.927,2.583 0.354,0.219 10 false HL2 0.958,2.365 1.25,2.531 0.292,0.167 10 false HL3 4.542,2.281 4.865,2.458 0.323,0.177 10 false HM1 4.917,2.281 5.229,2.448 0.313,0.167 10 false HM2 5.635,2.281 5.927,2.438 0.292,0.156 10 false HL1 6.021,2.281 6.313,2.438 0.292,0.156 10 false HL3 6.333,2.281 6.625,2.448 0.292,0.167 10 false HL2 5.354,2.281 5.469,2.448 0.115,0.167 10 false N 6.646,2.281 7.042,2.563 0.396,0.281 10 false GND

Standard Resistance:
Tester Connection Condition Specified Condition
A28-1 (HL1) - D46-4 (HL1) Always Below 1 Ω
A28-1 (HL1) - Body ground Always 100 kΩ or higher
A28-2 (HL2) - D46-6 (HL2) Always Below 1 Ω
A28-2 (HL2) - Body ground Always 100 kΩ or higher
A28-3 (HL3) - D46-5 (HL3) Always Below 1 Ω
A28-3 (HL3) - Body ground Always 100 kΩ or higher
A28-16 (NP) - D46-3 (N) Always Below 1 Ω
A28-16 (NP) - Body ground Always 100 kΩ or higher
A29-2 (HM1) - D46-1 (HM1) Always Below 1 Ω
A29-2 (HM1) - Body ground Always 100 kΩ or higher
A29-6 (HM2) - D46-2 (HM2) Always Below 1 Ω
A29-6 (HM2) - Body ground Always 100 kΩ or higher
D46-7 (GND) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector. If the harness or connector is normal, check the ECU output voltage.



b.

Check the 4WD control ECU (high-low transfer shift actuator).

i.

Connect the A28 and A29 ECU connectors.


ii.

Connect the D46 actuator connector.


iii.
U153508E02
0.875,2.052 0.333,2.917 false 1.813,2.052 0.906,2.917 false 1.885,2.031 1.302,2.896 false 1.958,2.052 1.688,2.917 false 2.188,1.99 2.188,2.896 false 2.708,2.135 2.708,2.896 false 2.948,1.594 2.677,1.99 true 0.188,0.031 2.51,0.427 2.323,0.396 10 false Component with harness connected: (4WD Control ECU) 1.135,1.458 1.448,1.615 0.313,0.156 10 false A28 1.573,2.927 1.854,3.104 0.281,0.177 10 false HL1 0.74,2.927 1.031,3.094 0.292,0.167 10 false HL3 1.156,2.927 1.448,3.094 0.292,0.167 10 false HL2 0.146,2.927 0.406,3.073 0.26,0.146 10 false NP 2.375,1.26 2.688,1.417 0.313,0.156 10 false A29 2.542,2.927 2.854,3.094 0.313,0.167 10 false HM2 3,1.521 3.333,1.771 0.333,0.25 10 true HM1 1.99,2.927 2.333,3.115 0.344,0.188 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-6 (HM2) - A29-4 (GND) Ignition switch ON
4WD control switch 4H → 4L (During operation of high-low transfer shift actuator motor from 4WD HIGH to 4WD LOW)
10 to 14 V
Ignition switch ON
4WD control switch 4H → 4L (High-low transfer shift actuator motor stopped)
Below 1.5 V
A29-2 (HM1) - A29-4 (GND) Ignition switch ON
4WD control switch 4L → 4H (During operation of high-low transfer shift actuator motor from 4WD LOW to 4WD HIGH)
10 to 14 V
Ignition switch ON
4WD control switch 4L → 4H (High-low transfer shift actuator motor stopped)
Below 1.5 V
A28-1 (HL1) - A29-4 (GND) Ignition switch ON
4WD control switch 4H
Below 1.5 V
Ignition switch ON
4WD control switch 4L
10.5 to 14 V
A28-2 (HL2) - A29-4 (GND) Ignition switch ON
4WD control switch 4H
10.5 to 14 V
Ignition switch ON
4WD control switch 4L
Below 1.5 V
A28-3 (HL3) - A29-4 (GND) Ignition switch ON
4WD control switch 4H
10.5 to 14 V
Ignition switch ON
1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation
Below 1.5 V
Ignition switch ON
Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation
10.5 to 14 V
A28-16 (NP) - A29-4 (GND) Ignition switch ON
1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation
Below 1.5 V
Ignition switch ON
Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation
10 to 14 V


HINT:

If there is a malfunction, determine if the malfunction is on the ECU side or the actuator side by disconnecting the connector of the high-low transfer shift actuator, and then checking the ECU output voltage.




c.

Check the 4WD control ECU.

i.

Connect the A28 and A29 ECU connectors.


ii.

Disconnect the D46 actuator connector.


iii.
U153525E01
0.369,0.254 2.738,0.676 2.369,0.423 10 Front view of wire harness connector: (to High-Low Transfer Shift Actuator) 0.449,1.258 0.748,1.423 0.299,0.165 10 D46 1.086,2.943 1.239,3.088 0.154,0.144 10 N 1.492,2.943 1.792,3.092 0.299,0.148 10 HL1 2.403,2.943 2.703,3.092 0.299,0.148 10 HL2 2.014,2.943 2.327,3.093 0.313,0.150 10 HL3 2.799,2.944 3.181,3.118 0.383,0.174 10 GND 1.924,2.209 1.632,2.891 false 1.683,2.209 1.202,2.891 false 2.147,2.209 2.147,2.891 false 2.388,2.209 2.525,2.891 false 2.594,2.209 2.972,2.891 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D46-3 (N) - D46-7 (GND) Ignition switch ON 10 to 14 V
D46-4 (HL1) - D46-7 (GND) Ignition switch ON 10.5 to 14 V
D46-5 (HL3) - D46-7 (GND) Ignition switch ON 10.5 to 14 V
D46-6 (HL2) - D46-7 (GND) Ignition switch ON 10.5 to 14 V


HINT:

If there is a malfunction, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL). If the voltage is normal, inspect the high-low transfer shift actuator, because the voltage applied to the motor cannot be measured.




d.

Inspect the high-low transfer shift actuator.

i.

Remove the transfer shift actuator (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY).


ii.

Check the 4WD HIGH to 4WD LOW switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD HIGH to 4WD LOW position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When inspecting the operation described above, use the stop light control relay (BRK NO. 1).


C160580E04
5.844,1.156 5.844,0.906 false 6.542,1.74 6.063,1.74 false 6.521,2.135 6.052,2.135 false 5.594,1.156 5.417,0.906 false 6.125,1.156 6.292,0.906 false 1.302,2.24 1.302,2.521 false 1.438,2.229 1.646,2.51 false 1.563,2.229 2,2.51 false 1.688,2.229 2.365,2.51 false 1.177,2.229 1.021,2.51 false 1.052,2.229 0.708,2.51 false 0.917,2.229 0.365,2.51 false 4.573,0.25 7.073,0.448 2.5,0.198 10 false Stop Light Control Relay (BRK NO. 1): 0.073,0.031 2.615,0.438 2.542,0.406 10 false Component without harness connector: (High-Low Transfer Shift Actuator) 0.042,0.76 1.74,0.948 1.698,0.188 10 false 4WD HIGH to 4WD LOW: 5.365,0.719 5.552,0.896 0.188,0.177 10 false 1 6.25,0.719 6.417,0.917 0.167,0.198 10 false 2 5.823,0.719 6.073,0.885 0.25,0.167 10 false 4 6.583,1.656 6.75,1.844 0.167,0.188 10 false 5 6.583,2.052 6.75,2.208 0.167,0.156 10 false 3 2.25,2.552 2.625,2.708 0.375,0.156 10 false HM1 1.896,2.552 2.24,2.719 0.344,0.167 10 false HM2 0.542,2.552 0.854,2.719 0.313,0.167 10 false HL2 0.896,2.552 1.208,2.719 0.313,0.167 10 false HL3 1.198,2.552 1.51,2.719 0.313,0.167 10 false HL1 1.615,2.552 1.74,2.719 0.125,0.167 10 false N 0.125,2.552 0.5,2.719 0.375,0.167 10 false GND

1.

After the 4WD HIGH to 4WD LOW switch is complete, inspect the neutral position detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (N) - 7 (GND) After 4WD HIGH to 4WD LOW switch is complete 100 kΩ or higher
4 (HL1) - 7 (GND) After 4WD HIGH to 4WD LOW switch is complete 100 kΩ or higher
5 (HL3) - 7 (GND) After 4WD HIGH to 4WD LOW switch is complete 100 kΩ or higher
6 (HL2) - 7 (GND) After 4WD HIGH to 4WD LOW switch is complete Below 1 Ω




iii.

Check the 4WD LOW to 4WD HIGH switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD LOW to 4WD HIGH position.

C160581E03
5.833,1.063 5.833,0.792 false 6.531,1.646 6.052,1.646 false 6.521,2.052 6.052,2.052 false 5.573,1.073 5.427,0.792 false 6.115,1.063 6.281,0.813 false 1.302,2.229 1.302,2.51 false 1.438,2.229 1.646,2.51 false 1.573,2.229 2,2.51 false 1.698,2.229 2.365,2.51 false 1.177,2.229 1.021,2.51 false 1.052,2.229 0.719,2.51 false 0.917,2.229 0.375,2.51 false 4.573,0.25 7.063,0.448 2.49,0.198 10 false Stop Light Control Relay (BRK NO. 1): 0.073,0.01 2.615,0.5 2.542,0.49 10 false Component without harness connector: (High-Low Transfer Shift Actuator) 0.063,0.76 1.719,1.021 1.656,0.26 10 false 4WD LOW to 4WD HIGH: 5.385,0.625 5.573,0.802 0.188,0.177 10 false 1 6.24,0.625 6.406,0.823 0.167,0.198 10 false 2 5.813,0.625 6.063,0.792 0.25,0.167 10 false 4 6.573,1.563 6.74,1.75 0.167,0.188 10 false 5 6.573,1.958 6.74,2.115 0.167,0.156 10 false 3 2.25,2.552 2.625,2.708 0.375,0.156 10 false HM1 1.896,2.552 2.24,2.719 0.344,0.167 10 false HM2 0.542,2.552 0.854,2.719 0.313,0.167 10 false HL2 0.896,2.552 1.208,2.719 0.313,0.167 10 false HL3 1.198,2.552 1.51,2.719 0.313,0.167 10 false HL1 1.615,2.552 1.74,2.719 0.125,0.167 10 false N 0.146,2.552 0.521,2.719 0.375,0.167 10 false GND

1.

After the 4WD LOW to 4WD HIGH switch is complete, inspect the neutral position detection switch and limit switch.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (N) - 7 (GND) After 4WD LOW to 4WD HIGH switch is complete 100 kΩ or higher
4 (HL1) - 7 (GND) After 4WD LOW to 4WD HIGH switch is complete Below 1 Ω
5 (HL3) - 7 (GND) After 4WD LOW to 4WD HIGH switch is complete 100 kΩ or higher
6 (HL2) - 7 (GND) After 4WD LOW to 4WD HIGH switch is complete 100 kΩ or higher


HINT:

If there is a malfunction, replace the transfer shift actuator (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY). If the transfer shift actuator is normal, replace the 4WD control ECU (See page Drivetrain>JF3A TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).