Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1751  Compressor Relay Coil Malfunction  


DESCRIPTION

When the "UP" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to the AIR SUS relay to turn it on.

As a result, the current flows to the AIR SUS relay coil, closing the relay contact, and then the battery positive voltage is applied to the compressor, which causes the compressed air to raise the vehicle height.

DTC Code Detection Condition Trouble Area
C1751 When either of the following is detected:
·

With the AIR SUS relay inactivated, an open signal of the AIR SUS relay is detected for 1 second or more.

·

With the AIR SUS relay activated, a short signal of the AIR SUS relay is detected 8 times successively.


·

Wire harness or connector

·

AIR SUS relay

·

Suspension control ECU



HINT:

Once the ECU stores DTC C1751 in the memory, the vehicle height control is suspended until a normal signal is input to the ECU from the AIR SUS relay. However, control is resumed if the ignition switch is turned off, then to ON again.


WIRING DIAGRAM

C179531E04
5.082,2.383 6.692,2.539 1.610,0.156 10 Suspension Control ECU 1.301,0.969 2.461,1.305 1.161,0.336 10 to Height Control Compressor 1.719,1.991 2.588,2.230 0.869,0.239 10 from Battery 3.233,1.468 3.842,1.754 0.610,0.286 10 AIR SUS 5.437,0.693 5.727,0.860 0.290,0.167 10 RC 4.995,0.679 5.387,0.923 0.392,0.244 10 O18 4.027,0.912 4.201,1.142 0.174,0.230 10 5 5.065,0.46 5.253,0.639 0.188,0.179 10 22 4.027,0.534 4.201,0.764 0.174,0.230 10 1 2.78,0.912 2.954,1.142 0.174,0.230 10 3 2.78,0.534 2.954,0.764 0.174,0.230 10 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


HINT:
·

If DTC C1781 (ECU malfunction) and/or C1782 (power source circuit) is displayed, perform the inspection necessary for DTC C1781 (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1781) and/or C1782 (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782) first.

·

If DTC C1781 and the C1782 are output at the same time, perform the inspection necessary for DTC C1782 first.



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (COMPRESSOR MOTOR RELAY)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and turn the Techstream main switch on.


c.

Enter the following menus: Chassis / Air suspension / Active Test.

Air Suspension
Tester Display Test Part Control Range Diagnostic Note
Compressor Motor Relay AIR SUS relay ON or OFF Operation of solenoid (clicking sound) can be heard

OK:

Operation of solenoid (clicking sound) can be heard


Result
Result Proceed to
NG A
OK (When troubleshooting according to the Problem Symptoms Table) B
OK (When troubleshooting according to the DTC Chart) C



A

2.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)
a.

Turn the ignition switch off.


b.
C149624E15
1.283,0.718 1.439,0.874 0.156,0.156 10 5 1.282,1.272 1.438,1.427 0.156,0.156 10 1 0.24,0.722 0.396,0.877 0.156,0.156 10 3 0.235,1.285 0.391,1.441 0.156,0.156 10 2 3.167,0.968 3.323,1.124 0.156,0.156 10 5 1.969,1.701 2.125,1.857 0.156,0.156 10 2 1.393,0.974 1.549,1.130 0.156,0.156 10 3 2.699,0.245 2.854,0.400 0.156,0.156 10 1

Remove the AIR SUS relay from the engine relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When 12 V battery voltage is not applied to terminal 1 and 2 10 kΩ or higher
When 12 V battery voltage is applied to terminal 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - ECU AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL RELAY

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - ECU AND BODY GROUND)
U153733E02
0.542,1.969 1.313,2.406 true 0.135,0.042 2.448,0.708 2.313,0.667 10 false Rear view of wire harness connector: (to Suspension Control ECU) 1.354,2.344 1.896,2.542 0.542,0.198 10 false 22 (RC) 3.719,0.063 5.385,0.49 1.667,0.427 10 false Engine Room Relay Block: 0.698,0.906 0.979,1.125 0.281,0.219 10 false O18

a.

Disconnect the O18 ECU connector.


b.

Remove the AIR SUS relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O18-22 (RC) - Relay block AIR SUS relay terminal 1 Always Below 1 Ω
O18-22 (RC) or Relay block AIR SUS relay terminal 1 - Body ground Always 10 kΩ or higher
Relay block AIR SUS relay terminal 2 - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR