Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1752  Height Control Compressor Motor Circuit Malfunction  


DESCRIPTION

When the "UP" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to switch the AIR SUS relay ON. As a result, the relay contacts close and the compressor motor turns on, producing compressed air.

The suspension control ECU detects the amount of current flow to the compressor motor by means of the differences in potential at terminals RM+ and RM- of the suspension control ECU. In this way, the suspension control ECU monitors the compressor circuit for abnormalities.

DTC Code Detection Condition Trouble Area
C1752 When either of the following is detected:
·

When the power supply voltage is at 12 V or higher, a lock signal of the height control compressor motor is detected for 4 seconds while the AIR SUS relay is activated.

·

When the power supply voltage is at below 12 V, a lock signal of the height control compressor motor is detected for 8 seconds while the AIR SUS relay is activated.


·

Wire harness or connector

·

No. 1 height control compressor

·

Suspension control ECU



HINT:

Once the ECU stores DTC C1752 in the memory, the vehicle height control is suspended until a normal signal is input to the ECU from the height control solenoid valves. However, control is resumed if the ignition switch is turned off, then ON again.


WIRING DIAGRAM

C179533E05
2.281,1.938 4.396,2.365 2.115,0.427 10 false No. 1 Height Control Compressor 1.375,3.646 2.135,4.021 0.76,0.375 10 false AIR SUS 3.333,2.854 4.729,3.219 1.396,0.365 10 false from Battery 2.479,0.688 2.781,0.854 0.302,0.167 10 false Q7 2.49,1.417 2.792,1.583 0.302,0.167 10 false Q7 5.677,1.417 5.979,1.604 0.302,0.188 10 false RM- 5.677,3.333 5.979,3.521 0.302,0.188 10 false RC 5.292,3.344 5.594,3.531 0.302,0.188 10 false O18 5.292,1.406 5.594,1.594 0.302,0.188 10 false O17 5.292,0.688 5.594,0.875 0.302,0.188 10 false O17 5.271,4.052 6.896,4.448 1.625,0.396 10 false Suspension Control ECU 5.677,0.677 6.073,0.865 0.396,0.188 10 false RM+ 2.802,1.427 2.948,1.615 0.146,0.188 10 false E 2.802,0.667 2.958,0.854 0.156,0.188 10 false B 2.542,0.49 2.698,0.677 0.156,0.188 10 false 1 2.542,1.229 2.698,1.417 0.156,0.188 10 false 2 3.875,0.49 4.031,0.677 0.156,0.188 10 false 3 2,2.729 2.156,2.917 0.156,0.188 10 false 5 1.208,2.729 1.365,2.917 0.156,0.188 10 false 3 3.875,1.229 4.031,1.417 0.156,0.188 10 false 4 5.354,0.51 5.594,0.698 0.24,0.188 10 false 19 5.354,1.219 5.594,1.406 0.24,0.188 10 false 17 5.354,3.146 5.594,3.333 0.24,0.188 10 false 22 3.427,1.406 3.729,1.594 0.302,0.188 10 false RM- 3.406,0.677 3.74,0.865 0.333,0.188 10 false RM+ 3.813,0.688 4.115,0.854 0.302,0.167 10 false Q7 3.813,1.406 4.115,1.573 0.302,0.167 10 false Q7 2,3.229 2.156,3.417 0.156,0.188 10 false 1 1.208,3.229 1.365,3.417 0.156,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


HINT:
·

If DTC C1781 (ECU malfunction) and/or C1782 (power source circuit) is displayed, perform the inspection necessary for DTC C1781 (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1781) and/or C1782 (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782) first.

·

If DTC C1781 and the C1782 are output at the same time, perform the inspection necessary for DTC C1782 first.



PROCEDURE

1.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)
a.

Turn the ignition switch off.


b.
C149624E15
1.283,0.718 1.439,0.874 0.156,0.156 10 5 1.282,1.272 1.438,1.427 0.156,0.156 10 1 0.24,0.722 0.396,0.877 0.156,0.156 10 3 0.235,1.285 0.391,1.441 0.156,0.156 10 2 3.167,0.968 3.323,1.124 0.156,0.156 10 5 1.969,1.701 2.125,1.857 0.156,0.156 10 2 1.393,0.974 1.549,1.130 0.156,0.156 10 3 2.699,0.245 2.854,0.400 0.156,0.156 10 1

Remove the AIR SUS relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When 12 V battery voltage is not applied to terminal 1 and 2 10 kΩ or higher
When 12 V battery voltage is applied to terminal 1 and 2 Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR - ECU, BATTERY AND BODY GROUND)

NG

REPLACE SUSPENSION CONTROL RELAY

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR - ECU, BATTERY AND BODY GROUND)
U153734E02
1.75,3.917 1.417,4.188 true 2.042,3.917 2.344,4.156 true 1.771,3.688 1.396,3.438 true 2.031,3.688 2.375,3.438 true 5.708,2.521 5.958,3.063 true 5.583,2.521 5.313,3.063 true 4.135,0.135 6.417,0.854 2.281,0.719 10 false Rear view of wire harness connector: (to Suspension Control ECU) 0.552,2.698 2.969,3.26 2.417,0.563 10 false Front view of wire harness connector: (to Height Control Compressor) 1.094,3.781 1.365,3.958 0.271,0.177 10 false Q7 1.115,4.188 1.49,4.365 0.375,0.177 10 false RM+ 2.354,4.188 2.75,4.385 0.396,0.198 10 false RM- 4.938,3.073 5.563,3.271 0.625,0.198 10 false 19 (RM+) 5.76,3.083 6.365,3.271 0.604,0.188 10 false 17 (RM-) 1.292,3.26 1.427,3.438 0.135,0.177 10 false B 2.375,3.26 2.531,3.458 0.156,0.198 10 false E 0.583,0.177 2.281,0.521 1.698,0.344 10 false Engine Room Relay Block: 5.302,1.083 5.583,1.24 0.281,0.156 10 false O17

a.

Remove the AIR SUS relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay block AIR SUS relay terminal 5 - Body ground Always 11 to 14 V



c.

Disconnect the Q7 compressor connector.


d.

Disconnect the O17 ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block AIR SUS relay terminal 3 - Q7-1 (B) Always Below 1 Ω
Relay block AIR SUS relay terminal 3 or Q7-1 (B) - Body ground Always 10 kΩ or higher
Q7-2 (E) - Body ground Always Below 1 Ω
Q7-3 (RM+) - O17-19 (RM+) Always Below 1 Ω
Q7-3 (RM+) or O17-19 (RM+) - Body ground Always 10 kΩ or higher
Q7-4 (RM-) - O17-17 (RM-) Always Below 1 Ω
Q7-4 (RM-) or O17-17 (RM-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT NO. 1 HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 1 HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)
a.

Apply 12 V battery voltage to the compressor motor and check the operation of the motor.


C149625E03
0.254,0.264 2.757,0.656 2.503,0.392 10 Component without harness connected: (Height Control Compressor) 2.66,1.485 3.186,1.711 0.526,0.227 10 B (+) 0.464,1.485 0.780,1.666 0.316,0.182 10 E (-) 2.03,2.078 2.454,1.569 2.454,1.569 2.574,1.569 false 1.444,2.078 1.019,1.569 1.019,1.569 0.899,1.569 false

OK:
Measurement Condition Specified Value
12 V battery positive (+) → Terminal 1 (B)
12 V battery negative (-) → Terminal 2 (E)
Motor operates


NOTICE:
·

Do not allow the motor to operate for approximately 90 seconds or more.

·

If the compressor is shorted, locked, or has a similar type of malfunction, a large amount of current will be flowing. Therefore, if the motor does not operate, immediately stop this inspection.




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR