Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT
RM27L0U _53 Suspension _049316 ALIGNMENT / HANDLING DIAGNOSIS _0235715 REAR WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

For vehicles equipped with VSC, if the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

1.

Disconnect the negative battery terminal for more than 2 seconds.

2.

Reconnect the negative battery terminal.



PROCEDURE

Hide 3.INSPECT CAMBER

C107736E01
2.295,0.657 2.739,0.819 0.444,0.162 10 Gauge 2.033,1.261 2.15,0.77 2.15,0.77 2.25,0.77 false

a.

Install a camber-caster-kingpin gauge or put the wheels on a wheel alignment tester.


b.

Inspect the camber.

Standard Camber Inclination (Unloaded Vehicle):
Drive Type Rear Suspension Type Camber Inclination
2WD Coil -1°25' +/-45'
(-1.42°+/-0.75°)
Air -1°41' +/-45'
(-1.68°+/-0.75°)
4WD Coil -1°17' +/-45'
(-1.28°+/-0.75°)
Air -1°33' +/-45'
(-1.55°+/-0.75°)


If the measured value is not within the specified range, inspect the suspension parts for damage and wear. Replace parts as necessary because camber cannot be properly adjusted with any damaged or worn parts.



Hide 4.ADJUST CAMBER

C180800

a.

Loosen the camber adjust cam nut.


b.

Rotate the camber adjust cam on the vehicle side of No. 2 lower arm to adjust camber.

Standard Camber Inclination (Unloaded Vehicle):
Drive Type Rear Suspension Type Camber Inclination
2WD Coil -1°25' +/-45'
(-1.42°+/-0.75°)
Air -1°41' +/-45'
(-1.68°+/-0.75°)
4WD Coil -1°17' +/-45'
(-1.28°+/-0.75°)
Air -1°33' +/-45'
(-1.55°+/-0.75°)



c.

Tighten the nut.

Torque:
250 N*m (2549 kgf*cm, 185 ft.*lbf)


Hide 5.INSPECT TOE-IN

U154221E02
0.302,0.042 0.438,0.188 0.135,0.146 10 false A 1.698,1.917 1.833,2.063 0.135,0.146 10 false B 1.625,0.115 1.76,0.26 0.135,0.146 10 false C 1.49,0.5 1.854,0.667 0.365,0.167 10 false Front 3.073,0.031 3.208,0.177 0.135,0.146 10 false A

Standard toe-in (Unloaded Vehicle):
Drive Type Rear Suspension Type Specified Condition
2WD Coil A: -0°02' +/-4' (-0.03°+/-0.07°)
B - C: -1.0 +/-2 mm (-0.0394 +/-0.0787 in.)
Air A: -0°01' +/-4' (-0.02°+/-0.07°)
B - C: -0.3 +/-2 mm (-0.0118 +/-0.0787 in.)
4WD Coil A: -0°03' +/-4' (-0.05°+/-0.07°)
B - C: -1.4 +/-2 mm (-0.0551 +/-0.0787 in.)
Air A: -0°02' +/-4' (-0.03°+/-0.07°)
B - C: -0.7 +/-2 mm (-0.0276 +/-0.0787 in.)


If the toe-in is not within the specified range, inspect the suspension parts and replace if necessary.


Hide 6.ADJUST TOE-IN

C180801

a.

Loosen the toe adjust cam bolt.


b.

Rotate the toe adjust plate on the vehicle side of lower arm No. 2 to adjust toe-in.

Standard toe-in (Unloaded Vehicle):
Drive Type Rear Suspension Type Specified Condition
2WD Coil A: -0°02' +/-4' (-0.03°+/-0.07°)
B - C: -1.0 +/-2 mm (-0.0394 +/-0.0787 in.)
Air A: -0°01' +/-4' (-0.02°+/-0.07°)
B - C: -0.3 +/-2 mm (-0.0118 +/-0.0787 in.)
4WD Coil A: -0°03' +/-4' (-0.05°+/-0.07°)
B - C: -1.4 +/-2 mm (-0.0551 +/-0.0787 in.)
Air A: -0°02' +/-4' (-0.03°+/-0.07°)
B - C: -0.7 +/-2 mm (-0.0276 +/-0.0787 in.)



c.

Tighten the bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

Hide 10. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION