Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Skid Control Buzzer Circuit  


DESCRIPTION

The skid control buzzer sounds upon receiving a signal from the skid control ECU.

WIRING DIAGRAM

C160045E09
5.677,2.031 5.99,2.198 0.313,0.167 10 false A19 5.688,2.177 7.01,2.448 1.323,0.271 10 false Skid Control ECU 3.26,1.052 3.573,1.219 0.313,0.167 10 false H5 3.25,1.229 4.573,1.5 1.323,0.271 10 false Skid Control Buzzer 2.333,1.729 3.698,2 1.365,0.271 10 false from IG No. 1 Relay 1.625,0.885 2.542,1.094 0.917,0.208 10 false ECU-IG No. 1 5.823,1.302 6.302,1.5 0.479,0.198 10 false GND1 5.813,0.729 6.292,0.927 0.479,0.198 10 false BZ 5.594,0.604 5.708,0.802 0.115,0.198 10 false 9 3.156,0.594 3.323,0.792 0.167,0.198 10 false 2 5.542,1.198 5.729,1.396 0.188,0.198 10 false 16 4.167,0.604 4.333,0.802 0.167,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SKID CONTROL BUZZER)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


e.

According to the display on the Techstream, read the Data List.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Buzzer Skid control buzzer Buzzer ON/OFF Buzzer can be heard


f.

Check that the buzzer sounds/stops when turning the skid control buzzer on/off by using the Techstream.

Result
Result Proceed to
Buzzer does not sound or sounds constantly A
Buzzer sounds/stops B



A

2.INSPECT SKID CONTROL BUZZER (POWER SOURCE TERMINAL)

B

2.INSPECT SKID CONTROL BUZZER (POWER SOURCE TERMINAL)
a.
U153400E02
0.688,1.354 0.917,1.552 0.229,0.198 10 false H5 0.219,0.104 0.469,0.333 0.25,0.229 10 false *a

Disconnect the H5 buzzer connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H5-2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Buzzer)



OK

3.INSPECT SKID CONTROL BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.INSPECT SKID CONTROL BUZZER
a.
C140186E07
2.271,1.802 2,2.771 true 2.5,1.813 2.771,2.781 true 0.552,1.865 0.771,2.083 0.219,0.219 10 false (+) 1.229,1.844 1.448,2.063 0.219,0.219 10 false (-) 1.906,2.823 2.125,3.042 0.219,0.219 10 false 1 2.76,2.844 2.979,3.063 0.219,0.219 10 false 2 0.125,0.073 0.313,0.281 0.188,0.208 10 false *a

Disconnect the H5 buzzer connector.


b.

Apply battery negative voltage to terminal 1, and battery positive voltage to terminal 2 of the skid control buzzer, and then check that the buzzer sounds.

OK:

Skid control buzzer sounds.



Text in Illustration
*a Component without harness connected
(Skid Control Buzzer)


OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL BUZZER)

NG

REPLACE SKID CONTROL BUZZER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL BUZZER)
a.

Disconnect the A19 ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-9 (BZ) - H5-1 Always Below 1 Ω
A19-9 (BZ) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BODY GROUND)
a.

Disconnect the A19 ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-16 (GND1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR