Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In the sensor check mode, a malfunction of the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Transition to the sensor check mode can be performed by connecting terminals TS and CG of the DLC3 and turning the ignition switch from OFF to ON.

WIRING DIAGRAM

C140173E16
5.948,3.01 6.302,3.188 0.354,0.177 10 false A19 0.49,3.01 0.969,3.167 0.479,0.156 10 false H19 0.896,1 1.125,1.208 0.229,0.208 10 false TS 0.906,1.865 1.135,2.073 0.229,0.208 10 false CG 6.052,1 6.281,1.208 0.229,0.208 10 false TS 5.813,0.865 5.917,1.052 0.104,0.188 10 false 7 1.25,0.885 1.469,1.031 0.219,0.146 10 false 12 1.26,1.729 1.469,1.885 0.208,0.156 10 false 4 5.948,3.188 7.104,3.375 1.156,0.188 10 false Skid Control ECU 0.479,3.167 0.948,3.354 0.469,0.188 10 false DLC3

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DLC3)
a.
C353056E02
0.156,0.823 0.531,1.073 0.375,0.25 0.156,2.833 0.531,3.083 0.375,0.25 1.885,1.385 1.885,1.063 true 1.688,4.396 1.688,4.073 true 0.167,0.052 2.458,0.438 2.292,0.385 10 false Front view of wire harness connector: (to Skid Control ECU) 0.219,0.875 0.531,1.052 0.313,0.177 10 false A19 0.24,2.885 0.552,3.063 0.313,0.177 10 false H19 0.302,2.406 1.615,2.604 1.313,0.198 10 false Front view of DLC3: 1.802,0.865 2.135,1.031 0.333,0.167 10 false TS 1.573,4.438 1.906,4.604 0.333,0.167 10 false TS

Turn the ignition switch off.


b.

Disconnect the A19 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-7 (TS) - H19-12 (TS) Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
U153426E01
0.199,0.135 1.469,0.304 1.269,0.170 10 Front view of DLC3: 1.517,1.269 1.756,1.439 0.239,0.170 10 CG 0.223,1.104 0.555,1.262 0.332,0.158 10 H19 1.672,1.893 1.672,1.498 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-4 (CG) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
U153427E02
1.604,2.948 1.604,2.552 true 0.198,0.094 1.469,0.26 1.271,0.167 10 false Front view of DLC3: 1.531,3.01 1.771,3.177 0.24,0.167 10 false TS 0.198,1.115 0.531,1.271 0.333,0.156 10 false H19

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-12 (TS) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR