Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM27L0U _55 Steering _049326 POWER ASSIST SYSTEMS _0235759 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  Power Steering Warning Light Circuit  


DESCRIPTION

The power steering ECU is connected to the combination meter via CAN communication. If the power steering ECU detects a malfunction, the power steering warning light comes on. At this time, the vehicle enters fail-safe mode.

WIRING DIAGRAM

C225486E03
0.559,2.425 0.833,2.569 0.274,0.145 10 H37 0.559,2.592 2.396,2.765 1.836,0.173 10 Combination Meter Assembly 0.876,3.357 2.598,3.530 1.722,0.173 10 : CAN Communication Line 1.351,1.594 1.784,1.752 0.433,0.157 10 CANH 1.379,2.001 1.812,2.158 0.433,0.157 10 CANL 5.572,1.604 6.005,1.762 0.433,0.157 10 CANH 5.572,2.011 6.005,2.168 0.433,0.157 10 CANL 1.865,1.439 2.052,1.603 0.187,0.164 10 33 1.865,1.873 2.052,2.037 0.187,0.164 10 34 2.137,0.941 3.480,1.093 1.343,0.152 10 from IG1 No. 3 Relay 4.03,1.072 4.942,1.234 0.911,0.163 10 ECU-IG No. 2 5.572,0.941 5.766,1.098 0.194,0.157 10 IG 5.347,0.82 5.473,0.988 0.126,0.168 10 5 5.357,1.434 5.463,1.601 0.105,0.168 10 1 5.357,1.854 5.463,2.022 0.105,0.168 10 2 5.357,2.456 5.463,2.624 0.105,0.168 10 3 5.572,2.55 5.906,2.721 0.334,0.170 10 GND 4.918,3.092 5.303,3.255 0.385,0.163 10 H117 4.918,3.24 6.889,3.418 1.971,0.178 10 Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CAN COMMUNICATION SYSTEM
a.

Check for DTCs of the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - IG1 NO. 3 RELAY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - IG1 NO. 3 RELAY, BODY GROUND)
a.
U153677E01
0.067,0.021 0.259,0.177 0.193,0.156 10 *a 1.445,1.333 1.095,1.671 false 1.824,1.333 2.174,1.671 false 2.123,1.668 2.358,1.838 0.235,0.170 10 IG 0.91,1.668 1.297,1.819 0.387,0.151 10 GND 1.547,0.283 1.901,0.432 0.354,0.149 10 H117

Disconnect the power steering ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H117-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU)



OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (INDICAT. EPS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM ACTIVE TEST USING TECHSTREAM (INDICAT. EPS)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. EPS.


e.

Perform the Active Test of the combination meter using the Techstream.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. EPS Power steering warning light ON or OFF Perform the test with the vehicle stopped and the engine idling.


f.

Check that the power steering warning light operates in accordance with the Active Test.

HINT:

Reconnect the connectors and restore the vehicle to its previous condition before checking the combination meter.


OK:

The power steering warning light turns on and off in accordance with the Techstream operation.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG