Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM27L0U _55 Steering _049327 STEERING COLUMN _0235762 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2620  ECU Power Source Circuit Malfunction  


DESCRIPTION

The ECU power source circuit supplies positive voltage to the multiplex tilt and telescopic ECU.

DTC Code Detection Condition Trouble Area
B2620 While the auto away/return function, driving position memory function or manual control is in operation, the ECU power supply voltage remains at 10 V or less for 10 sec. or more after a voltage of 8 V or less is detected.
·

Battery

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C159209E32
3.906,0.802 4.74,1.104 0.833,0.302 10 false ECU-B1 0.615,0.635 1.854,0.969 1.24,0.333 10 false from Battery 5.813,0.635 6.688,0.969 0.875,0.333 10 false ECUB 5.802,2.344 6.281,2.625 0.479,0.281 10 false GND 5.563,0.531 5.75,0.719 0.188,0.188 10 false 9 5.521,2.24 5.771,2.417 0.25,0.177 10 false 11 5.615,2.875 5.938,3.031 0.323,0.156 10 false H57 5.615,3.042 6.698,3.479 1.083,0.438 10 false Multiplex Tilt and Telescopic ECU

PROCEDURE

1.INSPECT FUSE (ECU-B1)
a.
C353586E01
2.583,3 2.271,2.302 true 2.354,3.031 3.271,3.229 0.917,0.198 10 false ECU-B1

Remove the ECU-B1 fuse from the engine room junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B1 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
U153414E02
2.375,2.698 2.719,2.802 false 0.26,0.26 2.625,0.708 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 2.76,2.719 3.219,2.917 0.458,0.198 10 false ECUB 1.969,1.365 2.26,1.563 0.292,0.198 10 false H57

Disconnect the H57 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H57-9 (ECUB) - Body ground Always 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
U153413E02
1.854,2.594 1.26,3 true 0.104,0.104 2.469,0.552 2.365,0.448 10 false Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU) 1.063,3.01 1.458,3.208 0.396,0.198 10 false GND 1.979,1.333 2.271,1.531 0.292,0.198 10 false H57

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H57-11 (GND) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR