Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)
RM27L0U _55 Steering _049327 STEERING COLUMN _0235764 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) G

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 3.INSPECT TILT MOTOR

a.
C106479E16
2.677,0.969 2.417,0.969 false 2.417,0.969 2.083,1.542 false 0.667,0.969 0.906,0.969 false 0.906,0.969 1.354,1.531 false 0.719,3.229 0.875,3.229 false 0.875,3.229 1.333,3.552 false 2.688,3.208 2.521,3.208 false 2.521,3.208 2.094,3.563 false 2.719,0.854 3.281,1.052 0.563,0.198 10 false TIM- (+) 2.719,3.115 3.26,3.313 0.542,0.198 10 false TIM- (-) 0.031,0.854 0.667,1.052 0.635,0.198 10 false TIM+ (-) 0.052,3.115 0.688,3.313 0.635,0.198 10 false TIM+ (+) 0.042,0.042 2.563,0.406 2.521,0.365 10 false *a 0.042,2.26 2.583,2.625 2.542,0.365 10 false *a

Apply the 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

Text in Illustration
*a Component without harness connected
(Tilt Motor Connector)

OK:
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal J48-2 (TIM+)
12 V battery negative (-) lead → Terminal J48-1 (TIM-)
The steering wheel tilts up.
12 V battery positive (+) lead → Terminal J48-1 (TIM-)
12 V battery negative (-) lead → Terminal J48-2 (TIM+)
The steering wheel tilts down.



Hide 4.INSPECT TELESCOPIC MOTOR

a.
C149086E16
1.083,2.531 0.542,2.333 true 0.656,2.948 1.083,2.604 true 1.719,2.979 1.448,2.719 true 0.125,2.25 0.698,2.417 0.573,0.167 10 false TEM+ 0.281,2.885 0.75,3.073 0.469,0.188 10 false TEM- 0.604,0.281 3.198,0.698 2.594,0.417 10 false *a 1.771,2.938 2.469,3.198 0.698,0.26 10 false *b

Disconnect connector A from the multiplex tilt and telescopic ECU.

Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
*b Connector A


b.

Apply 12 V battery voltage to the multiplex tilt and telescopic ECU connector. Then check the steering wheel telescopic operation.

OK:
Measurement Condition Specified Condition
12 V battery positive (+) lead → Terminal A-2 (TEM+)
12 V battery negative (-) lead → Terminal A-6 (TEM-)
The steering column contracts.
12 V battery positive (+) lead → Terminal A-6 (TEM-)
12 V battery negative (-) lead → Terminal A-2 (TEM+)
The steering column extends.