Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235782 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E345031E01
0.604,0.781 2.896,0.979 2.292,0.198 10 false from LH-IG Fuse 5.427,0.667 5.573,0.906 0.146,0.24 10 false 2 3.281,0.667 3.552,0.906 0.271,0.24 10 false RB 3.958,0.667 4.229,0.906 0.271,0.24 10 false RL 4.208,0.667 4.354,0.906 0.146,0.24 10 false 1 2.865,1.219 3.313,1.375 0.448,0.156 10 false D21 2.865,1.406 4.656,1.823 1.792,0.417 10 false Park/Neutral Position Switch Assembly 3.104,0.667 3.25,0.906 0.146,0.24 10 false 2 5.646,0.76 6.01,1 0.365,0.24 10 false REV 5.479,1.438 5.927,1.594 0.448,0.156 10 false I61 5.479,1.625 6.719,2.083 1.24,0.458 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E285964

Enter the "Vehicle Signal Check Mode" screen. [Refer to Check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK)].


b.

Check that the display changes between ON and OFF according to the shift lever position.

HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.


OK:
Shift Lever Position Display
R ON
Except R OFF




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
U153954E01
0.067,0.058 0.309,0.243 0.242,0.186 10 *a 1.6,0.497 1.964,0.687 0.364,0.191 10 I61 0.063,0.733 0.392,0.904 0.330,0.171 10 REV 0.944,1.363 0.643,0.82 0.643,0.82 0.459,0.82 false

a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I61-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
I61-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the I61 radio and display receiver assembly connector.


b.

Disconnect the D21 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I61-2 (REV) - D21-1 (RL) Always Below 1 Ω
I61-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U154160E02
1.792,1.021 2.01,0.344 2.01,0.344 2.229,0.344 true 2.281,0.26 2.573,0.469 0.292,0.208 10 false RB 0.313,1.021 0.604,1.229 0.292,0.208 10 false D21 0.042,0 0.333,0.208 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)


Result
Result Proceed to
OK (for AB60E) A
OK (for AB60F) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR