Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E283703E01
5.771,4.906 5.948,5.083 0.177,0.177 10 false 5 5.729,1.385 5.906,1.563 0.177,0.177 10 false 10 5.063,2.813 5.24,2.99 0.177,0.177 10 false 9 4.01,2.813 4.188,2.99 0.177,0.177 10 false 2 5,1.375 5.177,1.552 0.177,0.177 10 false 12 5.708,5.083 6.104,5.24 0.396,0.156 10 false I27 5.719,1.573 6.115,1.729 0.396,0.156 10 false I26 4.969,2.99 5.26,3.146 0.292,0.156 10 false H54 3.938,2.979 4.198,3.198 0.26,0.219 10 false z12 4.969,1.563 5.26,1.719 0.292,0.156 10 false H54 4.5,5.073 4.927,5.25 0.427,0.177 10 false ILL- 6.031,5.073 6.458,5.25 0.427,0.177 10 false ILL- 6.073,1.573 6.5,1.75 0.427,0.177 10 false ILL+ 4.406,2.896 4.833,3.073 0.427,0.177 10 false EAC 4.427,1.469 4.854,1.646 0.427,0.177 10 false IL+2 4,1.375 4.177,1.552 0.177,0.177 10 false 5 5.594,5.729 6.927,6.417 1.333,0.688 10 false Navigation Receiver Assembly 4.125,3.802 5.083,4.438 0.958,0.635 10 false Spiral Cable Sub-assembly 0.708,6.26 2.667,6.5 1.958,0.24 10 false Steering Pad Switch Assembly 0.917,0.417 2.01,0.604 1.094,0.188 10 false from TAIL Relay 3.938,1.552 4.198,1.771 0.26,0.219 10 false z12 0.583,5.813 2.5,6.052 1.917,0.24 10 false Steering Pad Switch RH Side 0.583,3.479 2.5,3.719 1.917,0.24 10 false Steering Pad Switch LH Side 3.427,0.604 3.99,0.792 0.563,0.188 10 false PANEL 3.729,5.698 4.948,6.24 1.219,0.542 10 false Combination Meter Assembly 4.833,4.99 5.073,5.167 0.24,0.177 10 false 37 3.729,5.552 4.104,5.729 0.375,0.177 10 false H37

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
Illumination comes on for all components except steering pad switch assembly and navigation receiver assembly. C
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). D



A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

D

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
U153926E01
2.708,1.644 3.034,1.791 0.326,0.147 10 IL+2 2.093,1.663 2.661,1.708 false 0.097,0.067 0.513,0.277 0.416,0.210 10 *a 0.664,1.301 0.962,1.482 0.297,0.181 10 H54 0.628,1.825 0.954,1.971 0.326,0.147 10 EAC 1.011,1.869 1.647,1.674 false

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H54-12 (IL+2) - Body ground Light control switch tail or head position 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-9 (EAC) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
U154157E02
2.094,1.344 2.333,1.583 2.333,1.583 2.427,1.583 true 1.573,0.438 1.906,0.625 0.333,0.188 10 false I26 2.469,1.51 2.958,1.698 0.49,0.188 10 false ILL+ 0.135,0.104 0.396,0.302 0.26,0.198 10 false *a

Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I26-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I27 navigation receiver assembly connector.


b.

Disconnect the H37 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I27-5 (ILL-) - H37-37 (ILL-) Always Below 1 Ω
I27-5 (ILL-) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR