Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC Code DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected.
·

Meter/gauge system

·

Harness or connector

·

Navigation receiver assembly



WIRING DIAGRAM

E282587E02
0.671,1.721 1.008,1.884 0.336,0.163 10 H37 0.671,1.889 2.556,2.087 1.885,0.198 10 Combination Meter Assembly 4.86,1.721 5.308,1.884 0.448,0.163 10 I53 4.86,1.889 6.933,2.087 2.073,0.198 10 Navigation Receiver Assembly 4.944,0.905 5.142,1.068 0.198,0.163 10 17 2.079,0.891 2.568,1.054 0.489,0.163 10 35 1.757,1.014 1.989,1.190 0.232,0.177 10 +S 5.224,1.014 5.637,1.190 0.413,0.177 10 SPD

PROCEDURE

1.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).


b.

While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

OK:

The readings are equal or almost equal.




OK

NG

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U154177E02
1.25,1.333 0.917,1.979 true 1.667,0.219 2,0.406 0.333,0.188 10 false H37 0.76,1.99 1.094,2.177 0.333,0.188 10 false +S 2.969,3.604 3.313,3.792 0.344,0.188 10 false GND 1.26,3.854 1.521,4.042 0.26,0.188 10 false (A) 0.031,0.052 0.365,0.24 0.333,0.188 10 false *a

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


ii.

Connect an oscilloscope to terminal H37-35 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H37-35 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I53 navigation receiver assembly connector.


b.

Disconnect the H37 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I53-17 (SPD) - H37-35 (+S) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR