Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235786 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E300605E02
0.354,0.313 1.219,0.729 0.865,0.417 10 false from IG No.1 Relay 1.885,0.448 2.833,0.656 0.948,0.208 10 false ECU-IG No.1 3.365,1.219 5.156,1.438 1.792,0.219 10 false Drive Monitor Switch 3.375,1.063 3.698,1.292 0.323,0.229 10 false J2 5.438,2.281 6.979,2.667 1.542,0.385 10 false Clearance Warning ECU Assembly 5.448,2.125 5.906,2.354 0.458,0.229 10 false H128 4.729,0.417 4.99,0.604 0.26,0.188 10 false SK 5.01,0.198 5.167,0.417 0.156,0.219 10 false 8 2.896,0.198 3.052,0.417 0.156,0.219 10 false 7 3.083,0.417 3.313,0.615 0.229,0.198 10 false IG 5.667,0.292 5.896,0.49 0.229,0.198 10 false IG 5.406,0.198 5.635,0.427 0.229,0.229 10 false 11 5.406,1.563 5.635,1.792 0.229,0.229 10 false 16 5.667,1.677 5.833,1.854 0.167,0.177 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVE MONITOR SWITCH - BATTERY)
a.
U153162E02
2.25,1.604 2.354,1.958 2.354,1.958 2.448,1.958 true 0.094,0.052 0.344,0.25 0.25,0.198 10 false *a 1.604,0.573 1.802,0.74 0.198,0.167 10 false J2 2.5,1.875 2.75,2.031 0.25,0.156 10 false IG

Disconnect the drive monitor switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J2-7 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Drive Monitor Switch)


OK

2.INSPECT DRIVE MONITOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT DRIVE MONITOR SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - DRIVE MONITOR SWITCH AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - DRIVE MONITOR SWITCH AND BODY GROUND)
a.

Disconnect the H128 clearance warning ECU assembly connector.


b.

Disconnect the J2 drive monitor switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H128-11 (IG) - J2-8 (SK) Always Below 1 Ω
H128-11 (IG) or J2-8 (SK) - Body ground Always 10 kΩ or higher
H128-16 (E) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR