Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.08–2016.10
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS INSPECTION


a.

Move the vehicle to an area which can provide the space specified in the illustration to perform the beam axis inspection.

E224418E20
0.094,0.094 1.271,0.281 1.177,0.188 12 false for LH Side: 3.917,0.083 5.323,0.271 1.406,0.188 12 false for RH Side: 0.156,1.333 0.438,1.531 0.281,0.198 10 false 2 m 0.99,4 1.917,4.198 0.927,0.198 10 false 7 m (22.96 ft) 5.333,4 6.26,4.198 0.927,0.198 10 false 7 m (22.96 ft) 2.125,4.01 2.917,4.208 0.792,0.198 10 false 3 m (9.85 ft) 6.76,1.313 7.042,1.51 0.281,0.198 10 false 2 m 6.74,3.406 7.042,3.604 0.302,0.198 10 false 8 m 0.188,3.385 0.469,3.583 0.281,0.198 10 false 8 m 3.188,1.833 4.052,2.021 0.865,0.188 10 false Rear Bumper 0.875,0.531 2.094,0.719 1.219,0.188 10 false Left side of vehicle 5.115,0.521 6.427,0.708 1.313,0.188 10 false Right side of vehicle 1.292,4.354 2.375,4.552 1.083,0.198 10 false : Inspection Area 0.031,3.792 0.625,3.969 0.594,0.177 10 false (26.25 ft) 0.031,1.625 0.573,1.833 0.542,0.208 10 false (6.57 ft) 6.531,3.792 7.135,4 0.604,0.208 10 false (26.25 ft) 6.646,1.635 7.146,1.844 0.5,0.208 10 false (6.57 ft) 4.354,4.01 5.146,4.208 0.792,0.198 10 false 3 m (9.85 ft)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 10 m (32.81 ft) x L 10 m (32.81 ft) x H 4 m (13.13 ft)) shown in the illustration.

·

Check that DTC C1ABB and DTC C1ABC are not output.




b.

Procedure to enter the Test Mode

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


iv.

Turn the Techstream on.


v.

Switch the blind monitor sensor to Test Mode using the Techstream. Enter the following menus: Body Electrical / BSM / Utility / Test Mode.



c.
E224411E02
0.122,0.123 2.187,0.296 2.065,0.172 10 Blind spot monitor indicator 0.075,0.852 1.034,1.025 0.959,0.172 12 for LH Side: 0.075,2.66 1.034,2.833 0.959,0.172 12 for RH Side:

Perform the blind spot monitor beam axis inspection.

i.

Check that the blind spot monitor indicators are not illuminated.

NOTICE:

If an indicator is illuminated, the system is reacting to a piece of metal or some other object. In this case, move the vehicle to another place.



ii.

Place the reflector at position A.

SST
09870-60000  
09870-60010  
09870-60040  

HINT:

Set the reflector so that its center is 565 mm (1.85 ft) above the floor.



iii.

Enter Test Mode using the Techstream. Move the reflector from position A to B as shown in the illustration.

E224419E04
0.906,1.125 1.375,1.76 false 0.948,3.25 1.542,2.708 false 6.271,1.125 5.719,1.781 false 6.104,3.271 5.615,2.74 false 0.083,0.073 1.198,0.302 1.115,0.229 12 false for LH Side: 3.646,0.083 4.625,0.313 0.979,0.229 12 false for RH Side: 0.885,0.375 2.083,0.542 1.198,0.167 10 false Left side of vehicle 5.146,0.365 6.479,0.573 1.333,0.208 10 false Right side of vehicle 0.49,0.906 1.375,1.083 0.885,0.177 10 false Warning area 5.896,0.906 6.781,1.083 0.885,0.177 10 false Warning area 3.177,1.688 4.052,1.854 0.875,0.167 10 false Rear bumper 4.125,2.156 4.375,2.344 0.25,0.188 10 false 3 m 3.156,2.167 3.427,2.354 0.271,0.188 10 false 3 m 3.021,2.76 3.177,2.948 0.156,0.188 10 false A 4.052,2.76 4.177,2.948 0.125,0.188 10 false A 2.354,2.76 2.51,2.948 0.156,0.188 10 false B 4.729,2.76 4.854,2.948 0.125,0.188 10 false B 1.615,2.76 1.771,2.948 0.156,0.188 10 false C 5.438,2.76 5.594,2.948 0.156,0.188 10 false C 1.646,3.292 2.031,3.448 0.385,0.156 10 false 1.5 m 5.208,3.281 5.625,3.438 0.417,0.156 10 false 1.5 m 2.083,3.292 2.396,3.448 0.313,0.156 10 false 1 m 4.604,3.135 4.896,3.313 0.292,0.177 10 false 1 m 2.427,3.49 2.698,3.646 0.271,0.156 10 false 3 m 4.604,3.49 4.875,3.646 0.271,0.156 10 false 3 m 0.656,3.281 1.25,3.448 0.594,0.167 10 false Reflector 5.917,3.292 6.51,3.458 0.594,0.167 10 false Reflector 2.302,3.625 2.896,3.802 0.594,0.177 10 false (9.85 ft) 1.563,3.458 2.104,3.667 0.542,0.208 10 false (4.93 ft) 2.323,3.292 2.854,3.49 0.531,0.198 10 false (3.29 ft) 4.469,3.615 4.99,3.781 0.521,0.167 10 false (9.85 ft) 5.156,3.427 5.698,3.635 0.542,0.208 10 false (4.93 ft) 4.521,3.302 5.052,3.479 0.531,0.177 10 false (3.29 ft) 3.115,2.323 3.646,2.531 0.531,0.208 10 false (9.85 ft) 4.083,2.313 4.583,2.552 0.5,0.24 10 false (9.85 ft)

HINT:
·

Make sure that the orientation of the reflector is as shown in the illustration.

·

The range of allowable sensor installation angles (in the horizontal plane) with which the system can operate properly are illustrated by the different warning areas (drawn with dashed lines) shown in the illustration.



NOTICE:

While moving the reflector, make sure that no people or objects pass between the vehicle and the reflector.



iv.

After placing the reflector at the specified position, be sure to leave the inspection area quickly. Also, make sure that no objects other than the reflector are in the inspection area and check that the blind spot monitor indicator does not illuminate.

HINT:

If the indicator illuminates, repeat the same action (i.e. move the reflector from A to B). If the indicator illuminates again, check the installation of the blind spot monitor sensor.



v.

Move the reflector from position B to C as shown in the illustration.

HINT:

Make sure that the orientation of the reflector is as shown in the illustration.


NOTICE:

While moving the reflector, make sure that no people or objects pass between the vehicle and the reflector.



vi.

After placing the reflector at the specified position, be sure to leave the inspection area quickly. Also, make sure that no objects other than the reflector are in the inspection area and check that the blind spot monitor indicator illuminates.

HINT:

If the indicator does not illuminate, repeat the same action (i.e. move the reflector from B to C). If the indicator does not illuminate again, check the installation of the blind spot monitor sensor.



vii.

Finish Test Mode.




CHECK BLIND SPOT MONITOR INSTALLATION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.




b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

E233717E01
5.912,3.961 5.912,3.413 false 6.081,3.343 6.913,3.527 0.832,0.184 10 Floor surface 5.912,3.413 6.059,3.413 false 1.953,3.588 1.953,2.446 false 1.189,3.588 2.903,3.753 1.714,0.166 10 Blind Spot Monitor Sensor 3.125,3.441 4.816,3.645 1.691,0.205 10 Outward facing surface 2.298,2.115 2.983,3.504 false 0.161,0.064 1.797,0.248 1.635,0.184 10 Rear view of vehicle (RH): 5.056,1.213 5.582,0.619 false 5.582,0.619 5.729,0.619 false 5.764,0.556 6.208,0.793 0.444,0.236 10 Jig 4.611,3.251 4.874,3.251 false 4.909,3.19 5.483,3.426 0.574,0.236 10 Weight 2.983,3.504 3.095,3.504 false

E233716E20
1.698,0.844 3.042,1.385 1.344,0.542 10 false Hold this side against the blind spot monitor sensor RH. 1.365,2.823 2.833,3.24 1.469,0.417 10 false Position where string is to be secured 2.708,4.146 2.854,4.323 0.146,0.177 10 false A 3.948,4.135 4.094,4.313 0.146,0.177 10 false B 5.344,3.188 5.885,3.635 0.542,0.448 10 false 100 mm (3.94 in.) 1.01,6.177 2.271,6.385 1.26,0.208 10 false : Allowable range 0.25,0.198 0.802,0.438 0.552,0.24 12 false Jig: 4.146,0.844 5.542,1.375 1.396,0.531 10 false Hold this side against the blind spot monitor sensor LH. 3.271,1.698 3.552,1.896 0.281,0.198 10 false Top 1.542,4.99 1.688,5.167 0.146,0.177 10 false + 5.146,4.979 5.292,5.156 0.146,0.177 10 false -

Standard
A B
Blind spot monitor sensor RH 17 mm (0.67 in) -17 mm (-0.67 in)
Blind spot monitor sensor LH 8 mm (0.31 in) -26 mm (-1.02 in)

NOTICE:

Allowable ranges A and B are different between the blind spot monitor sensor LH and RH.



c.
E224437E28
1.229,3.615 1.469,4.021 false 2.521,0.635 2.917,1.167 false 0.781,3.573 0.729,3.854 false 0.552,3.833 0.271,3.906 false 0.271,3.906 0.271,4.281 false 1.417,1.99 1.552,1.667 1.552,1.667 1.635,1.667 false 1.469,4.021 1.563,4.021 false 0.094,0.083 1.448,0.292 1.354,0.208 12 false Vehicle rear (LH): 1.354,0.552 2.521,0.865 1.167,0.313 10 false Vehicle center line 1.604,3.938 2.229,4.104 0.625,0.167 10 false Stud bolt 1.552,0.99 2.344,1.156 0.792,0.167 10 false Vehicle front 0.688,3.844 0.813,4.063 0.125,0.219 10 false y 1.969,3.698 2.729,3.865 0.76,0.167 10 false Vehicle rear 0.063,4.281 2.438,4.448 2.375,0.167 10 false Line parallel to the vehicle center line 1.656,2.406 2.344,2.594 0.688,0.188 10 false 135.5 mm 1.677,1.583 2.698,1.906 1.021,0.323 10 false Stud bolt center line 1.688,2.594 2.375,2.781 0.688,0.188 10 false (5.33 in)

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard
Dimension Specified Value
y 37 to 77 mm (1.46 to 3.03 in)