Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Radio and Display Type)
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235795 REAR VIEW MONITOR SYSTEM(for Radio and Display Type) J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E280619E23
5.24,1.802 6.448,2.188 1.208,0.385 10 false Radio and Display Receiver Assembly 5.229,1.615 5.844,1.813 0.615,0.198 10 false I61 3.271,1.49 3.885,1.688 0.615,0.198 10 false D21 3.271,1.667 4.594,2.042 1.323,0.375 10 false Park/Neutral Position Switch Assembly 5.427,0.958 6.042,1.156 0.615,0.198 10 false REV 4.104,0.958 4.323,1.156 0.219,0.198 10 false RL 3.448,0.958 3.667,1.156 0.219,0.198 10 false RB 3.25,0.854 3.396,1.052 0.146,0.198 10 false 2 4.417,0.844 4.563,1.042 0.146,0.198 10 false 1 5.208,0.854 5.354,1.052 0.146,0.198 10 false 2 2.094,1.125 2.5,1.323 0.406,0.198 10 false LH-IG 0.313,0.958 1.708,1.219 1.396,0.26 10 false from IG No.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Function Check/Setting I" mode and select "Vehicle Signal" (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U153952E02
0.927,1.354 0.625,0.896 0.625,0.896 0.51,0.896 true 0.094,0.052 0.333,0.24 0.24,0.188 10 false *a 1.656,0.51 2.021,0.698 0.365,0.188 10 false I61 0.188,0.823 0.521,0.99 0.333,0.167 10 false REV

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I61-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
I61-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the I61 radio and display receiver assembly connector.


b.

Disconnect the D21 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I61-2 (REV) - D21-1 (RL) Always Below 1 Ω
I61-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U154159E02
1.792,1.021 2.521,0.698 2.521,0.698 2.74,0.698 true 2.792,0.615 3.083,0.823 0.292,0.208 10 false RB 1.573,0.333 1.865,0.542 0.292,0.208 10 false D21 0.094,0.052 0.385,0.26 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D21-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)

Result
Result Proceed to
OK (for AB60E) A
OK (for AB60F) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR