Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235803 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU intermittently monitors the LIN communication bus between the components related to the door and sliding roof. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the door and sliding roof is detected consecutively 3 times.

DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times.
·

Power window regulator master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Sliding roof drive gear sub-assembly

·

Back door ECU

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

E160665E02
0.78,1.694 0.974,1.875 0.195,0.181 10 H2 1.359,1.165 1.669,1.346 0.310,0.181 10 LIN2 1.789,1.021 1.960,1.203 0.171,0.181 10 10 3.037,1.021 3.193,1.203 0.156,0.181 10 6 4.237,1.021 4.393,1.203 0.156,0.181 10 7 3.274,1.165 3.584,1.346 0.310,0.181 10 LIN1 3.819,1.165 4.130,1.346 0.310,0.181 10 LIN2 5.406,1.021 5.562,1.203 0.156,0.181 10 9 5.642,1.165 5.876,1.346 0.233,0.181 10 LIN 0.78,1.842 1.785,2.023 1.005,0.181 10 Main Body ECU 3.198,1.694 3.408,1.875 0.210,0.181 10 M2 3.207,1.867 4.905,2.245 1.698,0.378 10 Power Window Regulator Master Switch Assembly 0.78,3.663 0.967,3.844 0.187,0.181 10 V2 1.314,3.134 1.709,3.315 0.395,0.181 10 MPX1 1.789,2.991 1.960,3.172 0.171,0.181 10 16 3.037,2.991 3.193,3.172 0.156,0.181 10 9 3.274,3.134 3.507,3.315 0.233,0.181 10 LIN 0.78,3.811 1.777,3.992 0.997,0.181 10 Back Door ECU 0.154,4.652 1.721,4.810 1.567,0.158 10 LIN Communication Line 3.198,3.663 3.369,3.844 0.171,0.181 10 L3 3.207,3.836 4.538,4.474 1.331,0.638 10 Front Power Window Regulator Motor Assembly RH 3.037,5.134 3.193,5.315 0.156,0.181 10 3 3.274,5.277 3.669,5.459 0.395,0.181 10 MPX1 3.198,5.806 3.392,5.988 0.195,0.181 10 U3 3.207,5.98 4.617,6.336 1.409,0.357 10 Sliding Roof Drive Gear Sub-assembly* 5.465,1.704 5.675,1.885 0.210,0.181 10 M3 5.475,1.877 6.835,2.409 1.360,0.532 10 Front Power Window Regulator Motor Assembly LH 0.338,6.364 1.418,6.545 1.079,0.181 10 *: w/ Sliding Roof 2.414,4.293 1.868,4.755 1.868,4.755 1.735,4.755 false

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REGULATOR MOTOR LH)
a.
E345006E01
0.25,1.646 0.656,1.896 0.406,0.25 0.552,3.708 0.958,3.958 0.406,0.25 2.01,1.75 2.49,1.323 2.49,1.323 2.667,1.323 true 1.781,4.188 2.26,3.76 2.26,3.76 2.438,3.76 true 0.135,0.094 3.083,0.469 2.948,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 0.177,2.365 3.031,2.719 2.854,0.354 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 0.375,1.688 0.771,1.885 0.396,0.198 10 false M2 0.667,3.76 1.063,3.958 0.396,0.198 10 false M3 2.719,1.24 3.115,1.438 0.396,0.198 10 false LIN2 2.521,3.677 2.917,3.875 0.396,0.198 10 false LIN

Disconnect the M2 power window regulator master switch assembly connector.


b.

Disconnect the M3 front power window regulator motor assembly LH connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-7 (LIN2) - M3-9 (LIN) Always Below 1 Ω
M2-7 (LIN2) or M3-9 (LIN) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
M2-7 (LIN2) - Body ground Always Below 1 V



d.

Reconnect the power window regulator master switch assembly connector.


e.

Reconnect the front power window regulator motor assembly LH connector.



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)
U154037E02
2.052,1.417 2.427,1.292 true 5.604,1.542 6.177,1.302 true 5.802,3.177 6.229,3.01 true 2.208,5.281 2.49,5.354 true 1.813,3.76 2.406,3.563 true 0.656,1.292 0.854,1.469 0.198,0.177 10 false H2 4.302,1.469 4.51,1.646 0.208,0.177 10 false M2 0.448,0.042 2.813,0.438 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 4.104,0.042 6.469,0.583 2.365,0.542 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 2.49,1.167 2.802,1.344 0.313,0.177 10 false LIN2 6.24,1.208 6.552,1.385 0.313,0.177 10 false LIN1 4.417,3.229 4.615,3.406 0.198,0.177 10 false U3 4.094,2.042 6.521,2.521 2.427,0.479 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear Sub-Assembly)* 0.771,5.063 0.958,5.24 0.188,0.177 10 false V2 0.469,4.063 2.906,4.417 2.438,0.354 10 false Front view of wire harness connector: (to Back Door ECU) 6.302,2.948 6.698,3.125 0.396,0.177 10 false MPX1 2.531,5.281 2.927,5.458 0.396,0.177 10 false MPX1 0.844,3.5 1.01,3.677 0.167,0.177 10 false L3 0.51,2.042 2.938,2.563 2.427,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 2.458,3.49 2.688,3.667 0.229,0.177 10 false LIN 4.813,5.135 5.896,5.313 1.083,0.177 10 false *: w/ Sliding Roof

a.

Disconnect the H2 main body ECU connector.


b.

Disconnect the M2 power window regulator master switch assembly connector.


c.

Disconnect the L3 front power window regulator motor assembly RH connector.


d.

Disconnect the U3* sliding roof drive gear sub-assembly connector.


e.

Disconnect the V2 back door ECU connector.


f.

Measure the resistance and voltage according to the value(s) in the tables below.

HINT:

*: w/ Sliding Roof


Standard Resistance:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - M2-6 (LIN2) Always Below 1 Ω
H2-10 (LIN2) - L3-9 (LIN)
H2-10 (LIN2) - U3-3 (MPX1)*
H2-10 (LIN2) - V2-16 (MPX1)
H2-10 (LIN2) - Body ground Always 10 kΩ or higher


HINT:

*: w/ Sliding Roof


Standard Voltage:
Tester Connection Condition Specified Condition
H2-10 (LIN2) - Body ground Always Below 1 V



g.

Reconnect the main body ECU connector.


h.

Reconnect the power window regulator master switch assembly connector.


i.

Reconnect the front power window regulator motor assembly RH connector.


j.

Reconnect the sliding roof drive gear sub-assembly connector*.


k.

Reconnect the back door ECU connector.

HINT:

*: w/ Sliding Roof




OK

3.SYSTEM CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
Vehicle with Sliding roof A
Vehicle without Sliding roof B



A

4.CLEAR DTC

B

6.CLEAR DTC
4.CLEAR DTC
a.

Disconnect the U3 sliding roof drive gear sub-assembly connector.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B


b.

Reconnect the sliding roof driver gear sub-assembly connector.



A

6.CLEAR DTC

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

6.CLEAR DTC
a.

Disconnect the M3 power window regulator motor assembly LH connector.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B


b.

Reconnect the power window regulator motor assembly LH connector.



A

8.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

8.CLEAR DTC
a.

Disconnect the M2 power window regulator master switch assembly connector.




NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B


b.

Reconnect the power window regulator master switch assembly connector.



A

10.CLEAR DTC

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

10.CLEAR DTC
a.

Disconnect the L3 power window regulator motor assembly RH connector.




NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B


b.

Reconnect the power window regulator motor assembly RH connector.



A

12.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CLEAR DTC
a.

Disconnect the V2 back door ECU connector.




NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B


b.

Reconnect the back door ECU connector.



A

REPLACE MAIN BODY ECU

B

REPLACE BACK DOOR ECU