Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235816 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns off when the engine hood is opened and turns on when the engine hood is closed.

WIRING DIAGRAM

B148196E23
5.71,4.349 6.756,4.523 1.046,0.174 10 Main Body ECU 5.71,4.177 5.943,4.352 0.233,0.174 10 H4 5.787,2.17 6.234,2.344 0.447,0.174 10 HCTY 2.346,2.748 4.368,2.922 2.022,0.174 10 (Engine Hood Courtesy Switch) 2.346,2.601 3.771,2.796 1.425,0.195 10 Hood Lock Assembly 2.347,2.433 2.691,2.607 0.345,0.174 10 A35 2.812,2.053 2.956,2.202 0.144,0.148 10 2 5.518,2.053 5.700,2.202 0.183,0.148 10 16 3.69,2.053 3.834,2.202 0.144,0.148 10 1

PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect a Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream main switch on.


d.

Select the item below in the Data List and read the display on the Techstream.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hood Courtesy Switch Engine hood courtesy switch signal ON/OFF ON: Engine hood is OPEN
OFF: Engine hood is CLOSED
-

OK:

The indicator on the Techstream switches between ON and OFF in accordance with the engine hood courtesy switch status.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE HOOD COURTESY SWITCH
2.INSPECT ENGINE HOOD COURTESY SWITCH
a.

Disconnect the A35 engine hood courtesy switch connector.

B165961E02
0.606,2.243 1.735,2.424 1.129,0.181 10 UNLOCK Position 3.203,2.243 4.131,2.424 0.928,0.181 10 LOCK Position 4.618,0.05 7.104,0.400 2.486,0.350 10 Component without harness connected: (Engine Hood Courtesy Switch) 1.363,0.176 3.503,0.359 2.140,0.184 10 Engine Hood Lock Assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 LOCK position Below 1 Ω
UNLOCK position 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE HOOD COURTESY SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE HOOD COURTESY SWITCH)
a.

Disconnect the H4 main body ECU connector.

B443056E03
4.427,1.583 4.781,1.802 0.354,0.219 0.781,1.552 1.135,1.771 0.354,0.219 2.563,1.792 2.979,2.229 false 0.844,0.115 3.188,0.552 2.344,0.438 10 false Front view of wire harness connector: (to Main Body ECU) 4.219,0.104 6.563,0.542 2.344,0.438 10 false Front view of wire harness connector: (to Engine Hood Courtesy Switch) 3.042,2.188 3.563,2.385 0.521,0.198 10 false HCTY 0.875,1.573 1.146,1.771 0.271,0.198 10 false H4 4.469,1.604 4.74,1.802 0.271,0.198 10 false A35


b.

Disconnect the A35 engine hood courtesy switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-16 (HCTY) - A35-1 Always Below 1 Ω
A35-2 - Body ground Always Below 1 Ω
H4-16 (HCTY) or A35-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR