Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235822 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU

·

ECM


·

Start the engine and wait 10 seconds.*1

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2

*1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.

*2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B365295E04
0.748,2.044 2.661,2.247 1.914,0.203 10 A27 0.751,2.196 1.093,2.336 0.342,0.140 10 ECM 5.502,1.941 5.785,2.079 0.283,0.138 10 H32 5.502,2.102 6.913,2.411 1.411,0.309 10 Transponder Key ECU Assembly 1.415,1.332 1.650,1.471 0.236,0.138 10 IMI 1.372,0.575 1.671,0.713 0.299,0.138 10 IMO 5.858,0.575 6.148,0.729 0.291,0.154 10 EFII 5.858,1.332 6.220,1.486 0.362,0.154 10 EFIO 5.595,1.187 5.767,1.331 0.172,0.144 10 13 5.592,0.434 5.767,0.589 0.175,0.154 10 12 1.748,0.431 3.743,0.626 1.995,0.195 10 29 1.748,1.178 3.743,1.373 1.995,0.195 10 40

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Registration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>REGISTRATION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.


Result
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

B

3.REGISTER ECU COMMUNICATION ID

C

3.REGISTER ECU COMMUNICATION ID

NEXT

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (ECU COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

5.REPLACE ECM
5.REPLACE ECM
a.

Temporarily replace the ECM with a new one or known good one.




NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (ECM WAS DEFECTIVE)

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the H32 transponder key ECU assembly connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H32-12 (EFII) - A27-29 (IMO) Always Below 1 Ω
H32-13 (EFIO) - A27-40 (IMI) Always Below 1 Ω
H32-12 (EFII) - Body ground Always 10 kΩ or higher
H32-13 (EFIO) - Body ground Always 10 kΩ or higher
A27-29 (IMO) - Body ground Always 10 kΩ or higher
A27-40 (IMI) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR