Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235822 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

B443498E01
0.677,1.979 2.542,2.177 1.865,0.198 10 false Accessory Meter Assembly 5.333,2 6.719,2.354 1.385,0.354 10 false Transponder Key ECU Assembly 0.677,1.813 1.083,1.99 0.406,0.177 10 false I22 1.771,0.896 2.177,1.073 0.406,0.177 10 false 17 1.521,0.99 1.781,1.167 0.26,0.177 10 false LP 5.302,0.896 5.708,1.073 0.406,0.177 10 false 8 5.323,1.844 5.729,2.021 0.406,0.177 10 false H32 5.479,0.99 5.885,1.167 0.406,0.177 10 false IND

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Registration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>REGISTRATION).

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SECURITY INDICATOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -

OK:

Security indicator light can be turned on and off using the Techstream.




OK

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ACCESSORY METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ACCESSORY METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the H32 transponder key ECU assembly connector.


b.

Disconnect the I22 accessory meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H32-8 (IND) - I22-17 (LP) Always Below 1 Ω
H32-8 (IND) - Body ground Always 10 kΩ or higher
I22-17 (LP) - Body ground Always 10 kΩ or higher




OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the H32 transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I22-17 (LP) - Body ground Key not in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V




OK

REPLACE ACCESSORY METER ASSEMBLY (SECURITY INDICATOR LIGHT)

NG