Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM27L0U _58 Vehicle Interior _049337 THEFT DETERRENT / KEYLESS ENTRY _0235822 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B365295E05
0.818,2.044 2.731,2.247 1.914,0.203 10 A27 0.821,2.196 1.163,2.336 0.342,0.140 10 ECM 5.502,1.941 5.785,2.079 0.283,0.138 10 H32 5.502,2.102 6.913,2.411 1.411,0.309 10 Transponder Key ECU Assembly 1.415,1.332 1.650,1.471 0.236,0.138 10 IMI 1.372,0.575 1.671,0.713 0.299,0.138 10 IMO 5.858,0.575 6.148,0.729 0.291,0.154 10 EFII 5.858,1.332 6.220,1.486 0.362,0.154 10 EFIO 5.595,1.187 5.767,1.331 0.172,0.144 10 13 5.592,0.434 5.767,0.589 0.175,0.154 10 12 1.748,0.431 3.743,0.626 1.995,0.195 10 29 1.748,1.178 3.743,1.373 1.995,0.195 10 40

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Registration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>REGISTRATION).

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

OK

3.READ VALUE USING TECHSTREAM (IMMOBILISER FUEL CUT)

NG

3.READ VALUE USING TECHSTREAM (IMMOBILISER FUEL CUT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the Techstream.

Engine and ECT
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut / OFF/ON ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-

OK:

The item in the Data List indicates "OFF".


Result
Result Proceed to
OK (for 3UR-FE) A
OK (for 3UR-FBE) B
NG C



A

B

C

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

B

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>REGISTRATION).



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

7.REPLACE ECM
7.REPLACE ECM
a.

Temporarily replace the ECM with a new or known good one.




NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (ECM WAS DEFECTIVE)

NG

9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the H32 transponder key ECU assembly connector.


b.

Disconnect the A27 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H32-13 (EFIO) - A27-40 (IMI) Always Below 1 Ω
H32-12 (EFII) - A27-29 (IMO) Always Below 1 Ω
H32-13 (EFIO) - Body ground Always 10 kΩ or higher
H32-12 (EFII) - Body ground Always 10 kΩ or higher
A27-40 (IMI) - Body ground Always 10 kΩ or higher
A27-29 (IMO) - Body ground Always 10 kΩ or higher




OK

10.CHECK TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY ECU>REMOVAL).

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Registration (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>REGISTRATION).



b.

Using a registered key, turn the ignition switch to ON.


c.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started (for 3UR-FE) B
Engine cannot be started (for 3UR-FBE) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C