Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27L0U _58 Vehicle Interior _049339 METER / GAUGE / DISPLAY _0235844 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

The combination meter receives engine revolution signals from the ECM via the CAN line. The combination meter displays engine revolution data that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E344836E05
1.781,2.813 2.125,2.99 0.344,0.177 10 false ECM 4.885,2.792 6.073,2.99 1.188,0.198 10 false Combination Meter 3.281,1.74 3.896,1.938 0.615,0.198 10 false CAN Line

PROCEDURE

1.CHECK DTC
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN communication system DTC is not output A
CAN communication system DTC is output B



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (TACHOMETER)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (TACHOMETER)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the Techstream, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Tacho Meter Operation Tachometer 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 -

OK:

Needle indication is normal.


HINT:

Confirm that the vehicle is stopped and engine idling.




OK

3.READ VALUE USING TECHSTREAM (TACHOMETER)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING TECHSTREAM (TACHOMETER)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the Techstream, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed/Min.: 0, Max.: 12750 Idling: 650 to 750 Unit: rpm

OK:

Engine speed displayed on the Techstream is almost the same as that of the tachometer reading.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.READ VALUE USING TECHSTREAM (ENGINE SPEED)
4.READ VALUE USING TECHSTREAM (ENGINE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

According to the display on the Techstream, read the Data List.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed/Min.: 0, Max.: 16838 Idling: 650 to 750 Unit: rpm

OK:

Engine speed displayed on the Techstream is almost the same as that of the tachometer reading.


Result
Result Proceed to
Engine speed displayed on the Techstream is almost same as actual engine speed A
Engine speed displayed on the Techstream is not same as actual engine speed (for 3UR-FE) B
Engine speed displayed on the Techstream is not same as actual engine speed (for 3UR-FBE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C