Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27L0U _58 Vehicle Interior _049339 METER / GAUGE / DISPLAY _0235844 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter detects the fuel sender gauge malfunction.

DTC Code DTC Detection Condition Trouble Area
B1500 When combination meter detects fuel sender gauge malfunction
·

Harness or connector

·

Combination meter

·

Fuel sender gauge



WIRING DIAGRAM

B166182E03
4.444,2.997 4.722,3.186 0.278,0.188 10 H37 5.254,1.734 5.644,1.922 0.390,0.188 10 FUEL 4.185,0.704 4.398,0.893 0.213,0.188 10 12 4.185,1.25 4.398,1.438 0.213,0.188 10 39 2.604,1.25 2.772,1.438 0.168,0.188 10 2 3.476,1.25 3.644,1.438 0.168,0.188 10 3 4.456,0.704 4.822,0.893 0.366,0.188 10 L 4.456,1.25 4.822,1.438 0.366,0.188 10 E3 4.185,2.261 4.398,2.449 0.213,0.188 10 40 2.503,1.648 2.779,1.836 0.276,0.188 10 Q1 2.503,1.848 3.825,2.036 1.322,0.188 10 Fuel Sender Gauge 4.456,2.261 4.822,2.449 0.366,0.188 10 E1 4.444,3.179 5.723,3.367 1.279,0.188 10 Combination Meter

PROCEDURE

1.READ VALUE USING TECHSTREAM (FUEL SENDER GAUGE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the Techstream, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 Fuel sender input value Unit: L

OK:

Fuel value displayed on the Techstream is almost same as needle indication.




OK

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE AND BODY GROUND)
a.
U154004E02
1.083,1.448 0.74,1.646 true 1.604,1.375 1.458,1.885 true 1.146,1.458 1,1.792 true 0.198,0.031 2.542,0.417 2.344,0.385 10 false Rear view of wire harness connector: (to Combination Meter) 0.188,2.375 2.531,2.76 2.344,0.385 10 false Front view of wire harness connector: (to Fuel Sender Gauge) 0.896,1.792 1.104,1.958 0.208,0.167 10 false E3 0.49,1.594 0.698,1.76 0.208,0.167 10 false E1 0.469,1.271 0.76,1.438 0.292,0.167 10 false H37 1.375,1.875 1.51,2.042 0.135,0.167 10 false L 0.813,3.583 1.052,3.75 0.24,0.167 10 false Q1

Disconnect the H37 meter connector.


b.

Disconnect the Q1 gauge connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H37-12 (L) - Q1-2 Always Below 1 Ω
H37-39 (E3) - Q1-3 Always Below 1 Ω
H37-40 (E1) - Body ground Always Below 1 Ω
H37-12 (L) or Q1-2 - Body ground Always 10 kΩ or higher




OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
A156397E01
0.294,0.275 2.800,0.684 2.506,0.409 10 Component without harness connected: (Fuel Sender Gauge) 0.538,4.223 0.696,4.405 0.158,0.181 10 E 0.538,2.434 0.696,2.615 0.158,0.181 10 F 1.421,2.52 0.695,2.52 false 1.182,4.301 0.691,4.301 false

Remove the fuel sender gauge.

HINT:



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Float level is F (upper) 12 to 18 Ω
Float level is E (lower) 405 to 415 Ω


Result
Result Proceed to
Result is as specified A
Result is not as specified (for 3UR-FE) B
Result is not as specified (for 3UR-FBE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY