Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from OFF to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.

WIRING DIAGRAM

C159525E07
0.782,6.405 1.535,6.581 0.753,0.177 10 CAN Line 2.908,2.559 3.161,2.764 0.253,0.205 10 20 2.915,3.155 3.127,3.324 0.211,0.170 10 18 2.915,3.736 3.148,3.927 0.232,0.191 10 40 3.16,2.657 3.455,2.841 0.295,0.184 10 IG+ 3.16,3.26 3.469,3.457 0.309,0.198 10 B 3.16,3.834 3.490,4.039 0.330,0.205 10 E1 3.637,2.069 4.070,2.211 0.434,0.142 10 CANL 3.63,2.664 4.063,2.827 0.434,0.163 10 CANH 6.177,2.055 6.611,2.197 0.434,0.142 10 CANL 6.177,2.65 6.611,2.813 0.434,0.163 10 CANH 4.126,1.903 4.393,2.073 0.267,0.170 10 34 4.126,2.505 4.351,2.682 0.225,0.177 10 33 4.786,2.905 5.469,3.082 0.684,0.177 10 CAN Line 5.9,1.903 6.160,2.094 0.260,0.191 10 22 5.9,2.505 6.139,2.689 0.239,0.184 10 13 5.893,3.561 6.104,3.765 0.211,0.205 10 25 5.9,4.153 6.125,4.344 0.225,0.191 10 26 6.177,3.659 6.389,3.815 0.211,0.156 10 E1 6.177,4.261 6.417,4.431 0.239,0.170 10 E2 5.907,0.757 6.086,0.908 0.179,0.151 10 21 6.177,0.848 6.528,1.008 0.350,0.161 10 IG2 2.964,5.613 3.266,5.776 0.302,0.163 10 H37 2.964,5.789 4.204,5.972 1.239,0.184 10 Combination Meter 5.766,5.617 6.103,5.779 0.336,0.163 10 H56 5.766,5.775 7.141,5.949 1.375,0.174 10 Center Airbag Sensor 0.101,0.848 1.055,1.032 0.954,0.184 10 from IGN Fuse 0.101,2.637 1.101,2.820 1.000,0.184 10 from MET Fuse 0.233,3.246 1.019,3.616 0.787,0.371 10 from MET-B Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC is not output A
DTCs are output B



A

2.CHECK BATTERY

B

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery Always 11 to 14 V




OK

3.CHECK CONNECTORS

NG

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.
U153412E01
0.247,0.288 2.598,0.667 2.350,0.379 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.379,1.63 0.681,1.772 0.302,0.142 10 H56 1.049,3.078 1.289,3.234 0.239,0.156 10 E2 2.295,3.096 2.542,3.238 0.246,0.142 10 E1 2.854,2.339 3.128,2.502 0.274,0.163 10 IG2 1.677,2.485 1.238,3.053 false 1.797,2.468 2.321,3.07 false 2.407,2.425 2.82,2.425 false

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H56-21 (IG2) - H56-25 (E1) Ignition switch ON 11 to 14 V
H56-21 (IG2) - H56-26 (E2) Ignition switch ON 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
U153458E02
2.729,2.51 2.542,2.979 false 2.521,2.385 2.135,2.854 false 2.74,2.385 3.073,2.75 false 0.51,0.646 2.885,0.979 2.375,0.333 10 false Front view of wire harness connector: (to Combination Meter) 0.208,1.594 0.5,1.74 0.292,0.146 10 false H37 2.042,2.875 2.198,3.031 0.156,0.156 10 false B 2.458,3.01 2.656,3.167 0.198,0.156 10 false E1 3.021,2.792 3.302,2.948 0.281,0.156 10 false IG+

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the connector from the combination meter.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H37-18 (B) - H37-40 (E1) Always 11 to 14 V
H37-20 (IG+) - H37-40 (E1) Ignition switch ON 11 to 14 V




OK

6.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, SRS warning light goes off for approximately 10 seconds and remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




OK

NG