Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1650/32  Occupant Classification System Malfunction  


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor and the occupant classification system.

If the center airbag sensor receives signals from the occupant classification ECU, it determines whether the front passenger airbag, the front seat side airbag RH and front seat outer belt should be operated.

DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC Code Detection Condition Trouble Area
B1650/32 When one of following conditions is met:
·

Occupant classification system malfunction

·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit for 2 seconds.

·

Center airbag sensor malfunction


·

No. 2 Floor wire

·

Front seat wire RH (w/ power seat)

·

Occupant classification system

·

Center airbag sensor assembly



WIRING DIAGRAM

C158891E05
1.896,3.573 2.198,3.75 0.302,0.177 10 false P14 2.365,3.573 2.844,3.75 0.479,0.177 10 false W6 2.365,1.656 2.688,1.833 0.323,0.177 10 false W6 1.906,1.667 2.208,1.844 0.302,0.177 10 false P14 3.771,3.573 4.104,3.76 0.333,0.188 10 false PW1 3.76,1.677 4.094,1.865 0.333,0.188 10 false PW1 5.073,1.583 5.292,1.729 0.219,0.146 10 false 12 5.042,3.479 5.26,3.625 0.219,0.146 10 false 13 5.438,1.646 5.833,1.823 0.396,0.177 10 false FSP+ 5.448,3.573 5.844,3.75 0.396,0.177 10 false FSP- 1.396,1.625 1.792,1.802 0.396,0.177 10 false FSR+ 1.396,3.583 1.792,3.76 0.396,0.177 10 false FSR- 5.292,4.646 5.552,4.802 0.26,0.156 10 false P1 5.271,4.813 6.646,4.969 1.375,0.156 10 false Center Airbag Sensor 0.521,4.781 2.375,4.938 1.854,0.156 10 false Occupant Classification ECU 3.854,2.302 4.031,2.49 0.177,0.188 10 false *2 3.844,4.229 4.021,4.417 0.177,0.188 10 false *2 3.813,1.448 4.073,1.625 0.26,0.177 10 false 8*1 3.802,3.354 4.063,3.531 0.26,0.177 10 false 9*1 0.146,5.219 1.344,5.396 1.198,0.177 10 false *1: w/ Power Seat 0.146,5.469 1.438,5.646 1.292,0.177 10 false *2: w/o Power Seat 1.917,1.417 2.146,1.604 0.229,0.188 10 false 8*2 2.354,1.406 2.583,1.594 0.229,0.188 10 false 8*1 1.927,3.323 2.156,3.51 0.229,0.188 10 false 4*2 2.375,3.323 2.604,3.51 0.229,0.188 10 false 4*1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC (OCCUPANT CLASSIFICATION ECU)
a.

Turn the ignition switch to ON, and wait for at least 10 seconds.


b.

Check for the DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC is not output.




OK

2.CHECK VEHICLE SYSTEM

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK VEHICLE SYSTEM
a.

Check vehicle system.

Result
Result Proceed to
w/ Power seat A
w/o Power seat B



A

3.CHECK FOR DTC (CENTER AIRBAG SENSOR)

B

8.CHECK FOR DTC (CENTER AIRBAG SENSOR)
3.CHECK FOR DTC (CENTER AIRBAG SENSOR)
a.
C146235E11
0.063,1.188 1.563,1.542 1.5,0.354 10 false Occupant Classification ECU 2.021,1.063 2.917,1.417 0.896,0.354 10 false Center Airbag Sensor

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1650/32 is not output.


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




OK

NG

4.CHECK CONNECTION OF CONNECTORS
4.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

OK:

The connectors are properly connected.




OK

5.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

5.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the occupant classification ECU.


b.

Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are not deformed or damaged.




OK

6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT

NG

REPLACE HARNESS OR CONNECTOR

6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT
a.

Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

U153671E02
3.594,1.646 3.969,2.25 true 3.385,1.75 3.094,2.229 true 5.885,2.073 5.854,2.427 false 5.896,1.813 6.313,2.01 false 5.792,1.813 5.375,2.01 false 0.531,1.281 0.667,1.438 0.135,0.156 10 false F 0.802,1.49 0.969,1.656 0.167,0.167 10 false E 1.073,1.479 1.229,1.625 0.156,0.146 10 false D 1.177,1.479 1.313,1.635 0.135,0.156 10 false C 1.448,1.49 1.604,1.688 0.156,0.198 10 false B 1.729,1.281 1.896,1.448 0.167,0.167 10 false A 0.177,1.635 1.052,2.156 0.875,0.521 10 false Occupant Classification ECU 1.594,1.521 2.5,1.875 0.906,0.354 10 false Center Airbag Sensor 2.385,0.406 4.802,0.771 2.417,0.365 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.823,0.406 7.146,0.771 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.052,1.25 4.875,1.417 0.823,0.167 10 false Connector E 6.208,1.25 7.042,1.427 0.833,0.177 10 false Connector B 2.74,1.396 2.979,1.573 0.24,0.177 10 false W6 5.083,1.385 5.323,1.563 0.24,0.177 10 false P1 5.292,2.448 6.115,2.635 0.823,0.188 10 false Service Wire 2.854,2.26 3.26,2.438 0.406,0.177 10 false FSR+ 3.885,2.281 4.292,2.458 0.406,0.177 10 false FSR- 6.25,2.021 6.667,2.177 0.417,0.156 10 false FSP+ 5.146,2.021 5.563,2.177 0.417,0.156 10 false FSP-

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-8 (FSR+) - W6-4 (FSR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-8 (FSR+) - W6-4 (FSR-) Always 1 MΩ or higher
W6-8 (FSR+) - Body ground Always 1 MΩ or higher
W6-4 (FSR-) - Body ground Always 1 MΩ or higher



e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W6-8 (FSR+) - Body ground Ignition switch ON Below 1 V
W6-4 (FSR-) - Body ground Ignition switch ON Below 1 V




OK

NG

7.CHECK NO. 2 FLOOR WIRE
7.CHECK NO. 2 FLOOR WIRE
a.

Turn the ignition switch off.

U153672E02
0.958,1.333 0.958,0.531 0.958,0.531 0.885,0.531 false 1.354,1.438 1.354,2.219 false 3.635,1.708 3.927,2.229 true 3.542,1.698 3.24,2.208 true 5.885,1.823 6.375,2.115 true 5.792,1.813 5.375,2.125 true 5.854,2.052 5.698,2.406 false 0.177,0.448 0.865,0.75 0.688,0.302 10 false Front Seat Wire RH 1.031,2.229 2.094,2.406 1.063,0.177 10 false No. 2 Floor Wire 0.49,1.281 0.625,1.438 0.135,0.156 10 false F 0.74,1.479 0.906,1.646 0.167,0.167 10 false E 1,1.479 1.156,1.625 0.156,0.146 10 false D 1.167,1.479 1.302,1.635 0.135,0.156 10 false C 1.448,1.49 1.604,1.688 0.156,0.198 10 false B 1.719,1.281 1.885,1.448 0.167,0.167 10 false A 0.156,1.656 1.01,2.177 0.854,0.521 10 false Occupant Classification ECU 1.615,1.531 2.521,1.844 0.906,0.313 10 false Center Airbag Sensor 2.365,0.385 4.781,0.75 2.417,0.365 10 false Front view of wire harness connector: (to Joining Connector) 4.823,0.385 7.146,0.75 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.031,1.063 4.854,1.229 0.823,0.167 10 false Connector C 6.188,1.198 7.021,1.375 0.833,0.177 10 false Connector B 2.667,1.292 2.99,1.469 0.323,0.177 10 false PW1 5.156,1.302 5.479,1.479 0.323,0.177 10 false P1 5.146,2.427 5.969,2.615 0.823,0.188 10 false Service Wire 2.865,2.208 3.271,2.385 0.406,0.177 10 false FSR+ 3.969,2.229 4.375,2.406 0.406,0.177 10 false FSR- 6.479,2.125 6.896,2.281 0.417,0.156 10 false FSP+ 5.042,2.125 5.458,2.281 0.417,0.156 10 false FSP-


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the front seat wire RH connector from the No. 2 floor wire.


d.

Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PW1-8 (FSR+) - PW1-9 (FSR-) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PW1-8 (FSR+) - PW1-9 (FSR-) Always 1 MΩ or higher
PW1-8 (FSR+) - Body ground Always 1 MΩ or higher
PW1-9 (FSR-) - Body ground Always 1 MΩ or higher



h.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
PW1-8 (FSR+) - Body ground Ignition switch ON Below 1 V
PW1-9 (FSR-) - Body ground Ignition switch ON Below 1 V




OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK FOR DTC (CENTER AIRBAG SENSOR)
a.
C146230E17
0.039,1.403 1.519,1.735 1.480,0.333 10 Occupant Classification ECU 1.921,1.203 2.845,1.549 0.924,0.346 10 Center Airbag Sensor

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1650/32 is not output.


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




OK

NG

9.CHECK CONNECTION OF CONNECTORS
9.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

OK:

The connectors are properly connected.




OK

10.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

10.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the occupant classification ECU.


b.

Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are not deformed or damaged.




OK

11.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - OCCUPANT CLASSIFICATION ECU)

NG

REPLACE HARNESS OR CONNECTOR

11.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - OCCUPANT CLASSIFICATION ECU)
a.

Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

U153673E02
3.594,1.635 3.969,2.24 true 3.396,1.729 3.104,2.208 true 5.885,2.073 5.854,2.427 false 5.896,1.823 6.313,2.021 true 5.792,1.813 5.375,2.01 true 0.521,1.281 0.677,1.427 0.156,0.146 10 false D 0.802,1.49 0.938,1.646 0.135,0.156 10 false C 1.448,1.479 1.604,1.677 0.156,0.198 10 false B 1.729,1.281 1.896,1.448 0.167,0.167 10 false A 0.177,1.635 1.052,2.156 0.875,0.521 10 false Occupant Classification ECU 1.635,1.521 2.542,1.885 0.906,0.365 10 false Center Airbag Sensor 2.385,0.406 4.802,0.771 2.417,0.365 10 false Front view of wire harness connector: (to Occupant Classification ECU) 4.823,0.406 7.146,0.771 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 4.052,1.25 4.875,1.417 0.823,0.167 10 false Connector C 6.208,1.25 7.042,1.427 0.833,0.177 10 false Connector B 2.729,1.396 3.094,1.573 0.365,0.177 10 false P14 5.115,1.385 5.417,1.563 0.302,0.177 10 false P1 5.292,2.448 6.115,2.635 0.823,0.188 10 false Service Wire 2.875,2.24 3.281,2.417 0.406,0.177 10 false FSR+ 3.865,2.26 4.271,2.438 0.406,0.177 10 false FSR- 6.25,2.021 6.667,2.177 0.417,0.156 10 false FSP+ 5.146,2.021 5.563,2.177 0.417,0.156 10 false FSP- 0.052,0.521 1.052,0.719 1,0.198 10 false No. 2 Floor wire

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-8 (FSR+) - P14-4 (FSR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-8 (FSR+) - P14-4 (FSR-) Always 1 MΩ or higher
P14-8 (FSR+) - Body ground Always 1 MΩ or higher
P14-4 (FSR-) - Body ground Always 1 MΩ or higher



e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P14-8 (FSR+) - Body ground Ignition switch ON Below 1 V
P14-4 (FSR-) - Body ground Ignition switch ON Below 1 V




OK

NG

REPLACE NO. 2 FLOOR WIRE