Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor and the passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag, front seat side airbag RH and front seat outer belt RH.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC Code Detection Condition Trouble Area
B1660/43 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.

·

Passenger airbag ON/OFF indicator malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Integration control and panel (Passenger airbag ON/OFF indicator)

·

Center airbag sensor assembly



WIRING DIAGRAM

C181203E01
0.446,4.616 0.727,4.802 0.281,0.186 10 H45 0.453,4.773 2.404,4.947 1.951,0.174 10 Integration Control and Panel 5.473,4.606 5.791,4.780 0.318,0.174 10 H56 5.473,4.767 6.834,4.951 1.360,0.184 10 Center Airbag Sensor 5.645,0.89 6.134,1.101 0.489,0.211 10 PAON 5.661,1.899 6.053,2.082 0.392,0.184 10 P-AB 1.634,1.815 1.914,1.971 0.281,0.156 10 13 1.634,0.801 1.845,0.971 0.211,0.170 10 5 1.634,2.811 1.876,2.981 0.243,0.170 10 16 1.875,3.9 3.517,4.075 1.642,0.175 10 from ECU-IG No. 1 Fuse 5.358,0.799 5.583,0.983 0.225,0.184 10 23 5.679,2.936 5.890,3.105 0.211,0.170 10 E1 5.679,3.888 5.890,4.058 0.211,0.170 10 E2 5.371,1.829 5.582,1.999 0.211,0.170 10 17 5.348,2.815 5.591,3.001 0.243,0.186 10 25 5.356,3.816 5.581,3.969 0.225,0.152 10 26 1.183,1.922 1.577,2.078 0.394,0.156 10 P-AB 1.125,0.925 1.573,1.088 0.448,0.163 10 PAON 1.289,2.936 1.567,3.091 0.279,0.156 10 IG+ 3.252,1.919 3.613,2.130 0.361,0.211 10 HH1 3.353,1.697 3.578,1.881 0.225,0.184 10 4 3.252,0.924 3.613,1.136 0.361,0.211 10 HH1 3.353,0.702 3.578,0.886 0.225,0.184 10 3

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION ).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


C272587E13
3.125,0.979 3.854,1.146 0.729,0.167 10 false 4 seconds 4.031,0.896 4.719,1.063 0.688,0.167 10 false 2 seconds 3.125,1.948 3.854,2.115 0.729,0.167 10 false 4 seconds 4.031,1.917 4.719,2.083 0.688,0.167 10 false 2 seconds 4.615,3.073 6.792,3.438 2.177,0.365 10 false ON/OFF condition depends on the front passenger detection results. 0.313,2.448 1.521,3.083 1.208,0.635 10 false Passenger Airbag ON/OFF Indicator ("OFF") 0.281,1.448 1.521,2.083 1.24,0.635 10 false Passenger Airbag ON/OFF Indicator ("ON") 1.708,2.656 1.969,2.823 0.26,0.167 10 false Off 1.708,1.646 1.969,1.813 0.26,0.167 10 false Off 1.708,2.135 1.969,2.302 0.26,0.167 10 false On 1.708,1.167 1.969,1.333 0.26,0.167 10 false On 1.708,0.583 1.969,0.75 0.26,0.167 10 false Off 1.708,0.104 1.969,0.271 0.26,0.167 10 false On 0.375,0.323 1.448,0.51 1.073,0.188 10 false Ignition Switch

Result
ON/OFF Indicator Illumination Proceed to
Always ON A
OFF B



A

2.CHECK CONNECTION OF CONNECTORS

B

7.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the telltale light.


b.

Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are not deformed or damaged.




OK

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C157844

Connect the connector to the integration control and panel.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)
5.CHECK CENTER AIRBAG SENSOR
a.
C146229E63
0.354,0.979 1.542,1.729 1.188,0.75 10 false Integration Control and Panel (Passenger Airbag ON/OFF Indicator) 1.75,1.323 2.656,1.656 0.906,0.333 10 false Center Airbag Sensor

Connect the connector to the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)
U153460E02
1.219,0.177 1.125,0.177 1.125,0.177 1.125,1.198 false 3.656,1.708 4.094,2.01 true 6.115,1.646 6.552,1.948 true 5.708,2.021 5.156,2.438 false 5.802,1.51 5.25,1.927 true 3.646,1.583 3.104,2.052 true 0.073,1.646 1.271,1.958 1.198,0.313 10 false Integration Control and Panel 1.333,1.875 2.25,2.198 0.917,0.323 10 false Center Airbag Sensor 1.26,0.104 2.698,0.292 1.438,0.188 10 false Instrument Panel Wire 1.521,1.146 1.719,1.344 0.198,0.198 10 false A 1.219,1.375 1.417,1.573 0.198,0.198 10 false B 0.958,1.385 1.156,1.583 0.198,0.198 10 false C 0.646,1.167 0.844,1.365 0.198,0.198 10 false D 2.375,0.531 4.76,0.896 2.385,0.365 10 false Front view of wire harness connector: (to Integration Control and Panel) 4.833,0.531 7.156,0.896 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.781,1.417 3.083,1.594 0.302,0.177 10 false H45 4.979,1.458 5.271,1.635 0.292,0.177 10 false H56 6.49,1.938 6.948,2.083 0.458,0.146 10 false PAON 2.75,2.052 3.208,2.198 0.458,0.146 10 false PAON 4.031,2.031 4.49,2.177 0.458,0.146 10 false P-AB 4.938,1.948 5.396,2.094 0.458,0.146 10 false P-AB 3.167,2.26 4.021,2.469 0.854,0.208 10 false Connector C 5.552,2.292 6.406,2.5 0.854,0.208 10 false Connector B 4.302,2.427 5.135,2.604 0.833,0.177 10 false Service Wire

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the integration control and panel.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-5 (PAON) - H45-13 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-5 (PAON) - H45-13 (P-AB) Always 1 MΩ or higher
H45-5 (PAON) - Body ground Always 1 MΩ or higher
H45-13 (P-AB) - Body ground Always 1 MΩ or higher



h.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H45-5 (PAON) - Body ground Ignition switch ON Below 1 V
H45-13 (P-AB) - Body ground Ignition switch ON Below 1 V




OK

REPLACE INTEGRATION CONTROL AND PANEL

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the integration control and panel.

OK:

The connectors are properly connected.




OK

8.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the telltale light.


b.

Check that the connectors (on the center airbag sensor side and integration control and panel side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are not deformed or damaged.




OK

9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)
U153460E02
1.219,0.177 1.125,0.177 1.125,0.177 1.125,1.198 false 3.656,1.708 4.094,2.01 true 6.115,1.646 6.552,1.948 true 5.708,2.021 5.156,2.438 false 5.802,1.51 5.25,1.927 true 3.646,1.583 3.104,2.052 true 0.073,1.646 1.271,1.958 1.198,0.313 10 false Integration Control and Panel 1.333,1.875 2.25,2.198 0.917,0.323 10 false Center Airbag Sensor 1.26,0.104 2.698,0.292 1.438,0.188 10 false Instrument Panel Wire 1.521,1.146 1.719,1.344 0.198,0.198 10 false A 1.219,1.375 1.417,1.573 0.198,0.198 10 false B 0.958,1.385 1.156,1.583 0.198,0.198 10 false C 0.646,1.167 0.844,1.365 0.198,0.198 10 false D 2.375,0.531 4.76,0.896 2.385,0.365 10 false Front view of wire harness connector: (to Integration Control and Panel) 4.833,0.531 7.156,0.896 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.781,1.417 3.083,1.594 0.302,0.177 10 false H45 4.979,1.458 5.271,1.635 0.292,0.177 10 false H56 6.49,1.938 6.948,2.083 0.458,0.146 10 false PAON 2.75,2.052 3.208,2.198 0.458,0.146 10 false PAON 4.031,2.031 4.49,2.177 0.458,0.146 10 false P-AB 4.938,1.948 5.396,2.094 0.458,0.146 10 false P-AB 3.167,2.26 4.021,2.469 0.854,0.208 10 false Connector C 5.552,2.292 6.406,2.5 0.854,0.208 10 false Connector B 4.302,2.427 5.135,2.604 0.833,0.177 10 false Service Wire

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the integration control and panel.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-5 (PAON) - H45-13 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-5 (PAON) - H45-13 (P-AB) Always 1 MΩ or higher
H45-5 (PAON) - Body ground Always 1 MΩ or higher
H45-13 (P-AB) - Body ground Always 1 MΩ or higher



h.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H45-5 (PAON) - Body ground Ignition switch ON Below 1 V
H45-13 (P-AB) - Body ground Ignition switch ON Below 1 V




OK

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
U153498E01
0.309,0.241 2.753,0.622 2.444,0.382 10 Front view of wire harness connector: (to Integration Control and Panel) 0.382,2.025 0.709,2.215 0.326,0.191 10 H45 2.806,2.555 3.097,2.728 0.291,0.173 10 IG+ 2.344,2.318 2.785,2.619 false

Connect the connectors to the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H45-16 (IG+) - Body ground Ignition switch ON 11 to 14 V




OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL - BATTERY)

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
U153499E02
2.01,2.177 2.479,2.625 true 1.594,2 0.979,2.646 true 0.313,0.271 2.646,0.646 2.333,0.375 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 0.51,1.927 0.802,2.094 0.292,0.167 10 false H56 0.771,2.688 1.146,2.896 0.375,0.208 10 false P-AB 2.281,2.677 2.698,2.885 0.417,0.208 10 false PAON

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the integration control and panel.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Check the indicator according to the value(s) in the table below.

OK:
Connection Switch Condition Passenger airbag ON/OFF indicator
H56-23 (PAON) - Body ground Ignition switch ON "ON" comes on
H56-17 (P-AB) - Body ground Ignition switch ON "OFF" comes on




OK

12.CHECK CENTER AIRBAG SENSOR

NG

REPLACE INTEGRATION CONTROL AND PANEL

12.CHECK CENTER AIRBAG SENSOR
a.
C146229E11
0.217,0.966 1.397,1.306 1.180,0.340 10 Integration Control and Panel 1.739,1.276 2.630,1.598 0.891,0.323 10 Center Airbag Sensor

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connectors to the center airbag sensor.


d.

Connect the cable to the negative (-) battery terminal and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.




OK

NG