Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235858 FRONT PASSENGER AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

HINT:

When scrapping a vehicle equipped with the SRS or disposing of an instrument panel passenger airbag, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.


CAUTION:
·

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

·

Never dispose of a front passenger airbag that has an undeployed airbag.

·

The airbag emits an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (33 ft) away from the front passenger airbag.

·

The front passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front passenger airbag which has been deployed.

·

Do not apply water, etc. to a front passenger airbag which has been deployed.

·

Always wash your hands with water after completing the operation.

·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.



PROCEDURE

Hide 73960A 1.DISPOSE OF FRONT PASSENGER AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

HINT:
·

Prepare a battery as the power source to deploy the airbag.

·

In this procedure, the inflator of the front passenger airbag assembly is deployed first. Next, the actuator is deployed.



a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E01
2.541,0.591 3.056,0.813 0.514,0.222 10 Battery 1.788,1.612 2.124,1.813 0.336,0.201 10 SST 1.903,1.257 1.966,1.622 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Disconnect the cable from the negative battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Remove the instrument side panel RH (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


d.

Remove the No. 2 instrument panel under cover sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


e.


g.

Remove the lower instrument panel finish panel sub-assembly RH (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


h.

Remove the No. 2 instrument panel box door sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


i.
B325772E01
1.08,3.413 1.230,3.557 0.150,0.144 10 *1 0.766,3.853 0.839,3.492 0.839,3.492 1.067,3.492 false 1.316,0.976 1.466,1.120 0.150,0.144 10 *1 0.907,0.613 1.004,1.061 1.004,1.061 1.303,1.061 false

Slide the slider and disconnect the 2 airbag connectors.

Text in Illustration
*1 Slider

NOTICE:

Do not damage the airbag wire harness when handling the airbag connector.



j.
B385317E02
2.073,3.625 2.073,3.917 false 2.052,3.292 2.542,3.292 2.542,3.292 2.625,3.063 true 0.74,3.146 1.083,3.146 true 1.917,3.948 2.26,4.146 0.344,0.198 10 false SST 1.698,3.219 2.042,3.417 0.344,0.198 10 true SST 0.406,3.063 0.75,3.26 0.344,0.198 10 false SST 0.406,2.333 0.615,2.51 0.208,0.177 10 false *a 1.719,2.333 1.927,2.51 0.208,0.177 10 false *b

Connect SST.

i.

Connect the SST connector to the No. 2 instrument panel wire (inflator side).

SST
09082-00700  
09082-00780  

Text in Illustration
*a Actuator Side
*b Inflator Side

NOTICE:
·

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

·

At this time, do not connect SST to the No. 3 instrument panel wire (actuator side).




ii.
U138455E02
1.01,1.854 2.49,1.854 false 2.604,1.042 2.604,1.99 false 0.865,1.813 0.865,1.948 false 1.792,0.5 2.365,0.698 0.573,0.198 10 false Battery 0.375,1.146 0.76,1.344 0.385,0.198 10 false SST 1.021,1.438 2.531,1.635 1.51,0.198 10 false 10 m or more

Move SST to at least 10 m (33 ft) away from the vehicle.


iii.

Close all doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.



iv.

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.



k.

Deploy the front passenger airbag assembly inflator.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.


ii.

Press the SST activation switch and deploy the front passenger airbag assembly inflator.

CAUTION:
·

Make sure that no one is near the vehicle when deploying the airbag.

·

The front passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front passenger airbag which has been deployed.

·

Do not apply water, etc. to a front passenger airbag which has been deployed.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch illuminates.



iii.

Disconnect the red clip of SST from the battery positive (+) terminal and the black clip of SST from the negative (-) terminal.


iv.

Disconnect the SST (09082-00700) connector from SST (09082-00780).



l.

Deploy the front passenger airbag assembly actuator.

i.

Connect the SST connector to the No. 3 instrument panel wire (actuator side).

SST
09082-00700  
09082-00760  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.



ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.


iii.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


iv.

Press the SST activation switch and deploy the front passenger airbag assembly actuator.

CAUTION:
·

Make sure that no one is near the vehicle when deploying the airbag.

·

The front passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front passenger airbag which has been deployed.

·

Do not apply water, etc. to a front passenger airbag which has been deployed.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.




Hide 73960A 2.DISPOSE OF FRONT PASSENGER AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

HINT:
·

Prepare a battery as the power source to deploy the airbag.

·

In this procedure, the inflator of the front passenger airbag assembly is deployed first. Next, the actuator is deployed.



a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E01
2.541,0.591 3.056,0.813 0.514,0.222 10 Battery 1.788,1.612 2.124,1.813 0.336,0.201 10 SST 1.903,1.257 1.966,1.622 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Remove the front passenger airbag (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

When storing the front passenger airbag, keep the upper surface of the airbag deployment side facing upward.




c.

Connect SST.

i.
B379239E01
0.11,1.441 0.418,1.614 0.308,0.173 10 SST 0.519,1.143 0.295,1.337 0.295,1.337 0.295,1.424 false 1.62,0.43 1.927,0.603 0.308,0.173 10 SST 1.994,0.521 2.083,0.521 2.083,0.521 2.152,0.973 false 1.424,0.158 2.504,1.449 1.08,1.292 1.424,0.158 2.504,1.449 1.08,1.292 0.032,0.517 1.111,1.809 1.08,1.292 0.032,0.517 1.111,1.809 1.08,1.292 1.454,0.185 1.749,0.358 0.294,0.173 10 *a 0.06,0.55 0.354,0.723 0.294,0.173 10 *b

Connect the SST connector to the front passenger airbag assembly inflator side.

SST
09082-00802  (09082-10801, 09082-30801)

Text in Illustration
*a Actuator Side
*b Inflator side


ii.

Connect the SST connector to the front passenger airbag assembly actuator side.

SST
09082-00802  (09082-10801, 09082-40800)



d.
B104882E01
1.921,1.189 1.749,1.567 false 2.895,0.914 3.153,1.118 0.259,0.205 10 A 0.498,1.571 2.858,1.776 2.360,0.205 10 Stripped Wire Harness Section

Using a service-purpose wire harness for the vehicle, tie the front passenger airbag to the tire.

Cross-sectional area of stripped wire
Area Measurement
A 1.25 mm2 or more (0.0019 in.2 or more)

CAUTION:

Do not use a wire harness that is too thin or any other object to tie the front passenger airbag because it may snap due to the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 divided by 4


i.
B169926E01
2.451,2.386 2.609,2.542 0.159,0.156 10 A 0.503,1.378 0.626,1.543 0.123,0.165 10 B

Position the front passenger airbag inside the tire, as shown in the illustration.

Tire Size
Area Measurement
A 185 mm (7.28 in.)
B 360 mm (14.17 in.)

CAUTION:
·

Make sure that the wire harnesses are tight. If there is any slack in the wire harnesses, the front passenger airbag may become loose due to the shock when the airbag is deployed.

·

Always tie the front passenger airbag with the airbag deployment side facing inside the tire.



NOTICE:

The tire will be marked by the airbag deployment, so use a waste tire.




e.
B166461E01
2.71,0.068 3.414,0.416 0.704,0.348 10 Tire (2 or more) 2.71,1.253 3.414,1.601 0.704,0.348 10 Tire (2 or more)

Place the tires.

i.

Place at least 2 tires under the tire to which the front passenger airbag is tied.


ii.

Place at least 2 tires over the tire to which the front passenger airbag is tied. A disc wheel should be installed onto the top tire.

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.

·

As the tires may be damaged by the airbag deployment, use a tire that you are planning to throw away.




iii.
B105087E01
0.078,0.725 0.972,0.929 0.894,0.204 10 Wire Harness 1.273,0.254 1.124,0.805 1.124,0.805 2.094,0.286 false

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. It is highly dangerous when a loose wire harness results in the tires coming free due to the shock when the airbag is deployed.




f.
B166462E02
1.625,0.177 2.563,1.292 false 0.573,0.083 1.677,0.427 1.104,0.344 10 false Front Passenger Airbag Assembly 1.427,1.771 1.885,1.948 0.458,0.177 10 false Battery 0.146,1.427 0.438,1.604 0.292,0.177 10 false SST 0.771,2.771 1.615,2.948 0.844,0.177 10 false 10 m or more

Connect SST.

NOTICE:

To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.



g.

Deploy the front passenger airbag assembly inflator.

i.

Connect SST (09082-00700) connector to the SST (09082-10801).

NOTICE:

To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.



ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.


iii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire which the front passenger airbag assembly is tied to.


iv.

Press the SST activation switch and deploy the front passenger airbag assembly inflator.

CAUTION:

When deploying the airbag, make sure that no one is near the tire.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.



v.

Disconnect the red clip of SST from the battery positive (+) terminal and the black clip of SST from the negative (-) terminal.


vi.

Disconnect the SST (09082-00700) connector from SST (09082-10801).



h.

Deploy the front passenger airbag assembly actuator.

i.

Connect the SST (09082-00700) connector to SST (09080-40800).

NOTICE:

To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.



ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.


iii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire which the front passenger airbag assembly is tied to.


iv.

Press the SST activation switch and deploy the front passenger airbag assembly actuator.

CAUTION:

When deploying the airbag, make sure that no one is near the tire.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




i.
B166458E01
0.079,0.255 0.796,0.428 0.717,0.173 10 Plastic Bag 1.27,0.656 0.988,0.374 false

Dispose of the front passenger airbag.

CAUTION:
·

The front passenger airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front passenger airbag which has been deployed.

·

Do not apply water, etc. to a front passenger airbag which has been deployed.

·

Always wash your hands with water after completing the operation.



i.

Remove the front passenger airbag from the tire.


ii.

Place the front passenger airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.