Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235877 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  One or more Power Seat Motors do not Operate  


DESCRIPTION

When the front power seat switch is operated, a command signal is sent to the position control ECU. The position control ECU then controls the appropriate seat motor as needed. The position control ECU is designed so that a malfunction of the seat memory system will not interfere with manual seat control.

WIRING DIAGRAM

B188601E02
1.344,0.75 1.521,0.938 0.177,0.188 10 false X5 1.323,2.219 2.625,2.594 1.302,0.375 10 false Power Seat Motor (Front Vertical Motor) 1.354,3.302 1.542,3.469 0.188,0.167 10 false X7 1.375,4.583 1.604,4.792 0.229,0.208 10 false X8 1.073,5.885 2.594,6.083 1.521,0.198 10 false Front Seat Assembly LH 5.208,5.802 5.458,5.979 0.25,0.177 10 false X10 5.229,4.354 5.344,4.521 0.115,0.167 10 false 8 5.177,5.323 5.375,5.5 0.198,0.177 10 false 10 5.229,4.031 5.354,4.208 0.125,0.177 10 false 9 5.24,3.063 5.385,3.24 0.146,0.177 10 false 7 5.25,2.76 5.396,2.938 0.146,0.177 10 false 4 5.24,1.792 5.385,1.969 0.146,0.177 10 false 6 5.229,1.469 5.375,1.646 0.146,0.177 10 false 3 5.26,0.5 5.406,0.677 0.146,0.177 10 false 2 3.271,4.354 3.417,4.531 0.146,0.177 10 false 2 3.281,5.292 3.427,5.469 0.146,0.177 10 false 1 3.26,4.021 3.406,4.198 0.146,0.177 10 false 1 3.26,3.073 3.406,3.25 0.146,0.177 10 false 2 3.271,2.74 3.417,2.917 0.146,0.177 10 false 2 3.281,1.802 3.427,1.979 0.146,0.177 10 false 1 3.281,1.458 3.427,1.635 0.146,0.177 10 false 2 3.302,0.5 3.448,0.677 0.146,0.177 10 false 1 5.5,5.427 5.854,5.635 0.354,0.208 10 false RCL- 5.5,4.49 5.896,4.677 0.396,0.188 10 false RCL+ 5.5,4.146 5.823,4.344 0.323,0.198 10 false LFT- 5.521,3.208 5.854,3.406 0.333,0.198 10 false LFT+ 5.531,2.875 5.875,3.042 0.344,0.167 10 false FRV- 5.5,1.927 5.896,2.104 0.396,0.177 10 false FRV+ 5.5,1.594 5.865,1.771 0.365,0.177 10 false SLD- 5.521,0.625 5.917,0.802 0.396,0.177 10 false SLD+ 1.344,2.052 1.531,2.25 0.188,0.198 10 false X6 1.323,0.906 2.469,1.281 1.146,0.375 10 false Power Seat Motor (Sliding Motor) 1.344,3.458 2.458,3.792 1.115,0.333 10 false Power Seat Motor (Lifter Motor) 1.365,4.74 2.469,5.094 1.104,0.354 10 false Power Seat Motor (Reclining Motor) 5.198,6 6.927,6.375 1.729,0.375 10 false Front Power Seat Switch LH (Position Control ECU)

PROCEDURE

1.READ VALUE USING TECHSTREAM (FRONT POWER SEAT SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Driver seat / Data List.


e.

According to the display on the Techstream, read the Data List.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear Sliding switch signal (Rearward) / ON or OFF ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off
-
Slide Front Sliding switch signal (Forward) / ON or OFF ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off
-

OK:

On the Techstream screen, each item changes between ON and OFF according to above chart.




OK

2.PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR)

NG

REPLACE FRONT POWER SEAT SWITCH LH

2.PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

According to the display on the Techstream, perform the Active Test.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Seat Reclining Seat reclining operation Front/OFF/Rear -
Front Vertical Operation Seat front vertical operation Up/OFF/Down -
Lifter Operation Seat lifter operation Up/OFF/Down -
Seat Slide Operation Seat sliding operation Front/OFF/Rear -


OK:

The power seat motors operate normally.



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

3.INSPECT FRONT SEAT ASSEMBLY LH (POWER SEAT MOTOR)
3.INSPECT FRONT SEAT ASSEMBLY LH (POWER SEAT MOTOR)
a.

Remove the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL).


b.

Check operation of the sliding motor.

i.
B188327E07
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Sliding Motor)

Check if the seat moves smoothly when the battery is connected to the sliding motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Forward
Battery positive (+) → 2
Battery negative (-) → 1
Rearward




c.

Check operation of the reclining motor.

i.
B188327E05
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Reclining Motor)

Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Forward
Battery positive (+) → 1
Battery negative (-) → 2
Rearward




d.

Check operation of the front vertical motor.

i.
B188327E03
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Front Vertical Motor)

Check if the seat moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Upward
Battery positive (+) → 2
Battery negative (-) → 1
Downward




e.

Check operation of the lifter motor.

i.
B188327E04
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Lifter Motor)

Check if the seat moves smoothly when the battery is connected to the lifter motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Upward
Battery positive (+) → 1
Battery negative (-) → 2
Downward





OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POWER SEAT MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POWER SEAT MOTOR)
a.

Disconnect the X10 switch connector.

B443196E01
0.385,1.656 0.74,1.885 0.354,0.229 4.51,1.146 4.844,1.333 0.333,0.188 4.521,1.427 4.844,1.615 0.323,0.188 4.521,1.698 4.854,1.875 0.333,0.177 4.521,1.938 4.854,2.115 0.333,0.177 1.49,1.594 1.208,1.198 false 2.177,1.604 2.573,1.198 false 2.396,1.708 2.625,1.708 false 2.417,1.948 2.656,1.948 false 2.156,2.031 2.448,2.292 false 1.927,2.031 2.052,2.354 false 1.729,2.042 1.646,2.333 false 1.49,2.042 1.198,2.302 false 0.208,0.135 2.458,0.5 2.25,0.365 10 false Front view of wire harness connector: (to Front Power Seat Switch LH) 4.313,0.146 6.563,0.51 2.25,0.365 10 false Front view of wire harness connector: (to Power Seat Motor) 0.448,1.677 0.719,1.865 0.271,0.188 10 false X10 0.802,1.052 1.177,1.24 0.375,0.188 10 false SLD+ 2.604,1.042 2.979,1.229 0.375,0.188 10 false SLD- 2.698,1.865 3.073,2.052 0.375,0.188 10 false RCL- 2.698,1.615 3.073,1.802 0.375,0.188 10 false FRV- 2.479,2.333 2.854,2.521 0.375,0.188 10 false LFT- 1.938,2.396 2.313,2.583 0.375,0.188 10 false RCL+ 1.469,2.375 1.844,2.563 0.375,0.188 10 false LFT+ 0.927,2.313 1.302,2.5 0.375,0.188 10 false FRV+ 4.594,1.156 4.802,1.323 0.208,0.167 10 false X5 4.594,1.438 4.802,1.604 0.208,0.167 10 false X6 4.604,1.698 4.813,1.865 0.208,0.167 10 false X7 4.604,1.948 4.813,2.115 0.208,0.167 10 false X8


b.

Disconnect the X5, X6, X7 and X8 motor connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X10-2 (SLD+) - X5-1 Always Below 1 Ω
X10-2 (SLD+) or X5-1 - Body ground Always 10 kΩ or higher
X10-3 (SLD-) - X5-2 Always Below 1 Ω
X10-3 (SLD-) or X5-2 - Body ground Always 10 kΩ or higher
X10-4 (FRV-) - X6-2 Always Below 1 Ω
X10-4 (FRV-) or X6-2 - Body ground Always 10 kΩ or higher
X10-6 (FRV+) - X6-1 Always Below 1 Ω
X10-6 (FRV+) or X6-1 - Body ground Always 10 kΩ or higher
X10-7 (LFT+) - X7-2 Always Below 1 Ω
X10-7 (LFT+) or X7-2 - Body ground Always 10 kΩ or higher
X10-8 (RCL+) - X8-2 Always Below 1 Ω
X10-8 (RCL+) or X8-2 - Body ground Always 10 kΩ or higher
X10-9 (LFT-) - X7-1 Always Below 1 Ω
X10-9 (LFT-) or X7-1 - Body ground Always 10 kΩ or higher
X10-10 (RCL-) - X8-1 Always Below 1 Ω
X10-10 (RCL-) or X8-1 - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR